Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SWITCH › 2013.08–2017.10
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0092748 WINDOW DEFOGGER SWITCH G

WINDOW / GLASS  WINDOW DEFOGGER SWITCH  INSPECTION  


PROCEDURE

Hide 55900A 1.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (for LHD)

a.

Check the resistance.

i.
B348447C03
1.583,1.583 1.833,1.917 0.25,0.333 1.583,3 1.833,3.333 0.25,0.333 1.208,2.729 0.823,2.854 true 1.76,3.865 1.75,4.229 true 2.51,4.25 2.229,3.844 true 0.49,1.635 0.802,1.833 0.313,0.198 10 false *a 1.667,1.667 1.979,1.865 0.313,0.198 10 false A 1.667,3.083 1.979,3.281 0.313,0.198 10 false B 0.708,2.792 1.021,2.99 0.313,0.198 10 false E 1.656,4.271 1.969,4.469 0.313,0.198 10 false ILL+ 2.531,4.26 2.844,4.458 0.313,0.198 10 false D
*a Component without harness connected
(Heater Control and Accessory Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A-10 (E) - B-1 (D) OFF 10 kΩ or higher
A-10 (E) - B-1 (D) ON Below 1 Ω


If the result is not as specified, replace the heater control and accessory assembly.



b.

Check that the illumination lights.

i.

Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) →B-3 (ILL+)
Battery negative (-) → A-10 (E)
Illuminates


If the result is not as specified, replace the heater control and accessory assembly.



Hide 55900A 2.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (for RHD)

a.

Check the resistance.

i.
I109786C03
1.583,1.667 1.833,1.969 0.25,0.302 1.583,3.083 1.833,3.385 0.25,0.302 2.615,2.896 2.229,2.688 true 1.219,3.865 1.01,4.115 true 1.625,3.865 1.625,4.167 true 0.417,1.771 0.729,1.969 0.313,0.198 10 false *a 2.656,2.854 2.969,3.052 0.313,0.198 10 false E 0.917,4.115 1.229,4.313 0.313,0.198 10 false D 1.531,4.188 1.844,4.385 0.313,0.198 10 false ILL+ 1.667,1.75 1.823,1.948 0.156,0.198 10 false A 1.667,3.167 1.823,3.365 0.156,0.198 10 false B
*a Component without harness connected
(Heater Control and Accessory Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A-6 (E) - B-6 (D) OFF 10 kΩ or higher
A-6 (E) - B-6 (D) ON Below 1 Ω


If the result is not as specified, replace the heater control and accessory assembly.



b.

Check that the illuminates.

i.

Apply battery voltage to the heater control and accessory assembly and check that the heater control and accessory assembly illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → B-4 (ILL+)
Battery negative (-) → A-6 (E)
Illuminates


If the result is not as specified, replace the heater control and accessory assembly.