Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › 2013.08–2016.04
RM30M0E _52 Drivetrain _017092 DRIVE SHAFT / PROPELLER SHAFT _0092752 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER

a.
C294108C01
0.552,0.344 0.813,0.615 true 0.458,1.104 0.708,1.313 true 0.135,1.01 0.458,1.177 0.323,0.167 10 false SST 0.354,0.24 0.531,0.427 0.177,0.188 10 false *a
*a Steel Plate


Using SST, a steel plate and a press, install a new front drive shaft dust cover.

SST
09527-10011  

NOTICE:
·

The front drive shaft dust cover should be completely installed.

·

Be careful not to damage the front drive shaft dust cover.




Hide 2.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C177228C09
2.01,0.885 2.427,1.156 false 2.49,1.083 2.802,1.24 0.313,0.156 10 false *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard grease capacity:

125 to 135 g (4.41 to 4.76 oz.)



d.

Install the front axle outboard joint boot into the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the front axle outboard joint boot.

·

Keep the inside of the front axle outboard joint boot free of foreign matter.




Hide 43447F 3.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle outboard joint boot clamp onto the front axle outboard joint boot.


c.
C282247C01
2.156,1 2.531,0.76 false 2.563,0.667 3.021,0.865 0.458,0.198 10 false SST 1.677,0.021 1.99,0.177 0.313,0.156 10 false *a 2.552,1.573 2.865,1.729 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C282248E01
1.625,1.063 0.938,1.406 true 0.656,1.323 1.115,1.521 0.458,0.198 10 false SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

2.1 mm (0.0827 in.) or less


If the clearance is outside the specified range, retighten SST.


Hide 43447E 4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.

Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.


b.
C282249C01
2.219,1.281 2.76,1.073 false 2.802,0.979 3.26,1.177 0.458,0.198 10 false SST 1.781,0.042 2.094,0.198 0.313,0.156 10 false *a 2.49,1.792 2.802,1.948 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C282250E01
1.542,1.531 2.177,1.656 true 2.229,1.583 2.688,1.781 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

1.3 mm (0.0512 in.) or less


If the clearance is outside the specified range, retighten SST.


Hide 43474D 5.INSTALL FRONT DRIVE SHAFT DAMPER RH (for RH Side)

a.
C294111C01
2.917,1.667 2.917,1.333 false 3.333,1.667 3.333,1.26 false 2.531,1.667 2.531,1.26 false 3.24,1.708 3.427,1.885 0.188,0.177 10 false *1 2.854,1.719 3.052,1.885 0.198,0.167 10 false *2 2.448,1.708 2.635,1.885 0.188,0.177 10 false *1 1.698,0.458 2.156,0.656 0.458,0.198 10 false (A)
*1 Front Drive Shaft Damper Clamp
*2 Front Drive Shaft Damper RH


Install the front drive shaft damper RH and 2 new front drive shaft damper clamps onto the front drive outboard joint shaft assembly.


b.

Set the dimension as specified below.

Dimension (A):

404.7 to 408.7 mm (1.33 to 1.34 ft.)



c.

Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Install the 2 front drive shaft damper clamps onto the front drive shaft damper RH.


e.
C197579C01
1.5,1.125 1.073,0.625 true 0.781,0.51 1.313,0.76 0.531,0.25 10 false SST 1.938,0.135 2.25,0.292 0.313,0.156 10 false *a 1.958,1.854 2.271,2.01 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front drive shaft damper clamp, press it against the front drive shaft damper RH and slightly tighten SST.

SST
09521-24010  

HINT:

Use the same procedure for both sides.



f.

Tighten SST so that the front drive shaft damper clamp is pinched.

NOTICE:

Do not overtighten SST.


HINT:

Use the same procedure for both sides.



g.

Remove SST.


h.
C275178E02
0.927,1.177 1.542,1.26 true 1.594,1.177 2.052,1.375 0.458,0.198 10 false SST

Using SST, measure the clearance of the 2 front drive shaft damper clamps.

SST
09240-00020  

Clearance:

1.3 mm (0.0512 in.) or less


If the clearance is outside the specified range, retighten SST.


Hide 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C287114C01
0.688,1.323 0.688,1.552 false 1.698,1.521 1.698,1.75 false 2.49,1.667 2.49,1.896 false 2.896,1.25 2.896,1.479 false 0.635,1.583 0.948,1.74 0.313,0.156 10 false *1 1.646,1.781 1.958,1.938 0.313,0.156 10 false *2 2.438,1.917 2.75,2.073 0.313,0.156 10 false *3 2.844,1.5 3.156,1.656 0.313,0.156 10 false *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts onto the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C287115C01
1.552,1.615 2.448,1.792 2.448,1.792 2.073,1.313 true 2.5,1.729 2.813,1.885 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint onto the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it onto the front drive outboard joint shaft assembly end.



e.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.




f.
C287116

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard grease capacity:

134 to 144 g (4.73 to 5.07 oz.)



h.
C160821C10
1.365,1.24 0.979,0.75 0.979,0.75 1.781,0.771 true 0.781,0.646 1.094,0.802 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C287112N01
1.396,1.615 1.854,1.813 0.458,0.198 10 false (A)

Check whether each drive shaft dimension (A) is within specification.

Dimension (A):
LH Side 585.6 mm (1.92 ft.)
RH Side 827.6 mm (2.71 ft.)



Hide 43448F 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle inboard joint boot clamp onto the front axle inboard joint boot.


c.
C282251C01
2.167,1.271 2.719,1.052 false 2.76,0.969 3.219,1.167 0.458,0.198 10 false SST 1.74,0.052 2.052,0.208 0.313,0.156 10 false *a 2.438,1.781 2.75,1.938 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C282252E01
1.49,1.521 2.156,1.615 true 2.198,1.542 2.656,1.74 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00020  

Clearance:

1.3 mm (0.0512 in.) or less


If the clearance is outside the specified range, retighten SST.


Hide 43448G 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.


b.
C282401C01
2.156,1.188 2.729,1.073 true 2.771,0.979 3.229,1.177 0.458,0.198 10 false SST 1.75,0.042 2.063,0.198 0.313,0.156 10 false *a 2.5,1.792 2.813,1.948 0.313,0.156 10 false *b
*a Hold
*b Turn


Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


c.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



d.

Remove SST.


e.
C282402E01
0.823,1.719 1.438,1.49 true 0.542,1.646 1,1.844 0.458,0.198 10 false SST

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00020  

Clearance:

2.1 mm (0.0827 in.) or less


If the clearance is outside the specified range, retighten SST.