Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM30M0E _54 Brake _017100 BRAKE (FRONT) _0092766 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47547B 1.TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG

a.

Temporarily install the front disc brake bleeder plug to the front disc brake cylinder.

HINT:

Fully tighten the front disc brake bleeder plug after bleeding any air left in the system.



Hide 31478B 2.INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP

a.

Install the front disc brake bleeder plug cap to the front disc brake bleeder plug.


Hide 3.INSTALL PISTON SEAL

a.
C294087
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new piston seal as shown in the illustration.


b.

Install the piston seal to the front disc brake cylinder.

NOTICE:

Securely install the piston seal into the groove of the front disc brake cylinder.



Hide 47731 4.INSTALL FRONT DISC BRAKE PISTON (for Rear Drum Brake)

a.
C295469
0.531,1.854 0.875,1.854 false 0.583,2.719 0.927,2.719 false 0.313,1.771 0.625,1.969 0.313,0.198 10 false *1 0.375,2.646 0.688,2.844 0.313,0.198 10 false *2
*1 Cylinder Boot
*2 Front Disc Brake Piston
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot and front disc brake piston as shown in the illustration.


b.

Install the cylinder boot to the front disc brake piston as shown in the illustration.


c.
C282657

Install the seal portion of the cylinder boot into the groove portion of the front disc brake cylinder.

NOTICE:

Securely install the seal portion of the cylinder boot into the groove portion of the front disc brake cylinder.



d.

Install the front disc brake piston to the front disc brake cylinder.

NOTICE:

Do not install the cylinder boot after installing the front disc brake piston into the front disc brake cylinder.



e.
C295472

Make sure that the cylinder boot is securely installed into the groove of the front disc brake cylinder and front disc brake piston.


Hide 47731 5.INSTALL FRONT DISC BRAKE PISTON (for Rear Disc Brake)

a.
C256889
0.194,1.111 0.360,1.248 0.167,0.137 10 *1 0.202,2.126 0.355,2.286 0.154,0.160 10 *2 0.513,1.191 0.373,1.191 false 0.58,2.22 0.395,2.22 false
*1 Cylinder Boot
*2 Front Disc Brake Piston
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot and front disc brake piston as shown in the illustration.


b.

Install the cylinder boot to the front disc brake piston.


c.

Install the front disc brake piston to the front disc brake cylinder.

NOTICE:

Do not install the front disc brake piston forcibly in the front disc brake cylinder.



Hide 6.INSTALL CYLINDER BOOT (for Rear Disc Brake)

a.
C295470
0.396,0.958 0.615,1.021 true 0.625,1.167 0.563,1.333 true 0.219,0.875 0.531,1.073 0.313,0.198 10 false *1 0.458,1.375 0.771,1.573 0.313,0.198 10 false *2
*1 Set Ring
*2 Cylinder Boot


Install the cylinder boot into the front disc brake cylinder.

NOTICE:

Securely install the cylinder boot into the groove of the front disc brake cylinder.



b.

Install a new set ring.

NOTICE:
·

Securely install the set ring into the groove of the cylinder boot.

·

Do not damage the cylinder boot.