Home › Brake › BRAKE (REAR) › REAR BRAKE(for Drum Type) › 2013.08–2014.03
RM30M0E _54 Brake _017101 BRAKE (REAR) _0092769 REAR BRAKE(for Drum Type) A

BRAKE (REAR)  REAR BRAKE(for Drum Type)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 4.LOOSEN PARKING BRAKE CABLE

Hide 42403 5.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY

a.

Release the parking brake and remove the rear brake drum sub-assembly.

HINT:

If the rear brake drum sub-assembly cannot be removed easily, perform the following procedure.


i.
C233134C10
0,0 3.427,0 false
V100135

Contract


Remove the shoe adjusting hole plug.


ii.

Insert a screwdriver through the hole into the backing plate, and hold the automatic adjust lever away from the adjuster.


iii.

Using another screwdriver, contract the brake shoe by turning the adjusting bolt.



Hide 6.REMOVE REAR BRAKE STRUT KIT

a.
C282430C02
0.729,1.615 1.354,1.615 true 2.083,0.563 2.823,0.219 true 2.219,0.781 2.958,0.438 true 0.417,1.542 0.729,1.771 0.313,0.229 10 true SST 2.854,0.115 3.167,0.313 0.313,0.198 10 false *1 3.01,0.344 3.323,0.542 0.313,0.198 10 false *2
*1 Wheel Cylinder Boot
*2 Tension Spring


Using SST, separate the tension spring from the rear brake shoe (front).

SST
09921-00011  

NOTICE:

Do not damage the wheel cylinder boot.



b.
C282431E01
0.74,1.917 1.563,1.417 true 0.396,1.833 0.854,2.031 0.458,0.198 10 false SST

Using SST, remove the shoe hold down spring cup, shoe hold down spring, shoe hold down spring pin and rear brake shoe (front).

SST
09718-00011  


c.
C282432

Remove the shoe tension spring from the rear brake shoe (front) and rear brake shoe (rear).


d.
C282433E01
2.042,1.49 2.729,1.875 true 2.792,1.802 3.25,2 0.458,0.198 10 false SST

Using SST, remove the shoe hold down spring cup, shoe hold down spring, shoe hold down spring pin and rear brake shoe (rear).

SST
09718-00011  


e.
C282434

Remove the tension spring and rear brake strut kit from rear brake shoe (rear).


f.
C108972

Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the rear brake parking brake shoe lever sub-assembly.


Hide 7.REMOVE REAR BRAKE AUTOMATIC ADJUST LEVER

a.
C282435

Remove the rear brake automatic adjust lever tension spring and rear brake automatic adjust lever from the rear brake shoe (front).


Hide 8.REMOVE REAR BRAKE PARKING BRAKE SHOE LEVER SUB-ASSEMBLY

a.
C108973

Using a screwdriver, remove the C-washer and rear brake parking brake shoe lever sub-assembly from the rear brake shoe (rear).


Hide 47570 9.REMOVE REAR WHEEL BRAKE CYLINDER ASSEMBLY

a.
C241887

Using a 10 mm union nut wrench, disconnect the brake tube from the rear wheel brake cylinder assembly.


b.

Remove the bolt and rear wheel brake cylinder assembly from the backing plate.