Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT(for 2NZ-FE) › 2013.08–2016.10
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0094355 MANUAL TRANSAXLE UNIT(for 2NZ-FE) A

C54 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT(for 2NZ-FE)  DISASSEMBLY  


PROCEDURE

Hide 31204 1.REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 2.REMOVE CLUTCH RELEASE BEARING ASSEMBLY

Hide 31232A 3.REMOVE RELEASE BEARING HUB CLIP

Hide 31126 4.REMOVE CLUTCH RELEASE FORK BOOT

Hide 31236B 5.REMOVE RELEASE FORK SUPPORT

Hide 33101A 6.REMOVE MANUAL TRANSMISSION FILLER PLUG

a.
C283060

Remove the manual transmission filler plug and the gasket from the manual transmission case.


Hide 33104 7.REMOVE DRAIN PLUG SUB-ASSEMBLY

a.
C283061

Remove the drain plug sub-assembly and the gasket from the manual transmission case.


Hide 84210 8.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

a.
C293445N01
1.063,0.281 1.563,0.698 true 0.771,0.188 1.229,0.385 0.458,0.198 10 false SST

Disengage the 2 clamps to separate the wire harness of the back-up light switch assembly from the wire harness clamp bracket and the manual transmission case.


b.

Using SST, remove the back-up light switch assembly and the gasket from the manual transmission case.

SST
09817-16011  


c.

Remove the bolt and the wire harness clamp bracket from the transaxle case.


Hide 33111G 9.REMOVE MANUAL TRANSMISSION BREATHER PLUG

a.
C291380

Remove the manual transmission breather plug from the manual transmission case.


Hide 33590F 10.REMOVE FLOOR SHIFT SELECTING BELLCRANK ASSEMBLY

a.
C120750

Remove the 2 bolts, nut and the floor shift selecting bellcrank assembly from the manual transmission case.


b.

Remove the shift and select lever bush from the floor shift control shift lever.


Hide 33527 11.REMOVE FLOOR SHIFT CONTROL SHIFT LEVER

a.
C293454

Remove the nut and the washer.


b.
C120747

Using a brass bar and a hammer, remove the lock pin.

NOTICE:

Do not damage the threads of the lock pin.



c.

Remove the floor shift control shift lever from the shift and select lever shaft assembly.


d.

Remove the dust boot from the shift and select lever shaft oil seal.


Hide 33544C 12.REMOVE SHIFT LEVER DAMPER

a.
C293455

Remove the nut and the washer.


b.
C120745

Using a brass bar and a hammer, remove the lock pin.

NOTICE:

Do not damage the threads of the lock pin.



c.

Remove the shift lever damper and the dust boot from the shift and select lever shaft assembly.


Hide 30300 13.SECURE MANUAL TRANSAXLE ASSEMBLY

a.
C282895C01
1.229,1.865 0.698,1.042 0.698,1.042 2.594,1.802 true 0.531,0.917 0.844,1.115 0.313,0.198 10 false *a
*a Wooden Block


Place the manual transaxle assembly on wooden blocks.


Hide 33295A 14.REMOVE SHIFT GATE PIN

a.
C286559

Remove the shift gate pin and the washer from the manual transmission case.


Hide 33528B 15.REMOVE CONTROL SHAFT COVER

a.
C120742

Remove the 4 bolts, control shaft cover and the gasket from the manual transmission case.


Hide 33528C 16.REMOVE CONTROL SHAFT COVER OIL SEAL

a.
C267939C01
1.438,0.792 0.865,0.448 true 0.698,0.333 0.896,0.521 0.198,0.188 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the control shaft cover oil seal from the control shaft cover.

NOTICE:

Make sure not to damage the inside of the control shaft cover.



Hide 17.REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C284594

Remove the shift interlock plate bolt and the gasket from the manual transmission case.


b.
C286560

Remove the shift and select lever shaft assembly from the manual transmission case.


Hide 33102 18.REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

a.
C282896

Remove the 9 bolts.


b.
C288021C01
0.708,0 0.063,0 false
V100135

Projection Part


Using a plastic hammer, carefully tap the projections of the manual transmission case cover sub-assembly to remove the manual transmission case cover sub-assembly from the manual transmission case.

NOTICE:

Do not damage the manual transmission case.



Hide 33321G 19.REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.
C251589E02
1.885,0.708 2.219,0.906 false 2.26,0.823 2.719,1.021 0.458,0.198 10 false SST

Using SST and a hammer, loosen the staked part of the manual transmission output shaft rear set nut.

SST
09930-00010  


b.
C282898

Engage the 2 gears simultaneously to lock the transmission.


c.

Using a 27 mm socket wrench, remove the manual transmission output shaft rear set nut.


d.

Disengage the 2 gears.


Hide 33214G 20.REMOVE NO. 3 GEAR SHIFT FORK

a.
C282899

Remove the No. 3 gear shift fork set bolt from the No. 3 gear shift fork.


b.
C282900

Remove the No. 3 transmission hub sleeve with the No. 3 gear shift fork from the No. 3 transmission clutch hub.


c.

Remove the No. 3 gear shift fork from the No. 3 transmission hub sleeve.


Hide 21.INSPECT 5TH GEAR THRUST CLEARANCE

a.
C282901

Using a dial indicator, measure the 5th gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 5th gear or input shaft rear radial ball bearing.


Hide 22.INSPECT 5TH GEAR RADIAL CLEARANCE

a.
C282902

Using a dial indicator, measure the 5th gear radial clearance.

Standard clearance:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)


Maximum clearance:

0.058 mm (0.00228 in.)


If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.


Hide 33393 23.REMOVE NO. 3 TRANSMISSION CLUTCH HUB

a.
C282903

Using 2 screwdrivers and a hammer, tap out the snap ring.

HINT:

Use a piece of cloth to keep the snap ring from flying off.



b.
C157373

Using a screwdriver, remove the synchromesh shifting key spring from the No. 3 transmission clutch hub.


c.
C287902C01
1.188,1.448 0.521,1.552 0.521,1.552 1.021,0.969 true 0.219,1.469 0.677,1.667 0.458,0.198 10 false SST 1.948,0.292 2.26,0.49 0.313,0.198 10 false *b 0.313,1.146 0.625,1.344 0.313,0.198 10 false *a
*a Hold
*b Turn


Using SST, remove the No. 3 transmission clutch hub, 5th gear and the No. 3 synchronizer ring from the input shaft.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)
09950-60010  (09951-00200)


d.
C282905

Remove the 3 synchromesh shifting keys and the synchromesh shifting key spring from the No. 3 transmission clutch hub.


Hide 33336A 24.REMOVE 5TH GEAR NEEDLE ROLLER BEARING

a.
C282906

Remove the 5th gear needle roller bearing and the 5th gear bearing spacer from the input shaft.


Hide 33428C 25.REMOVE 5TH DRIVEN GEAR

a.
C287904C01
1.427,1.417 0.75,1.167 0.75,1.167 1.281,0.948 true 0.438,1.083 0.896,1.281 0.458,0.198 10 false SST 0.333,0.542 0.646,0.74 0.313,0.198 10 false *a 1.854,0.177 2.167,0.375 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the 5th driven gear from the output shaft.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03021)
09950-60010  (09951-00180, 09952-06010)


Hide 33151D 26.REMOVE REAR BEARING RETAINER

a.
C282908

Remove the 5 bolts and the rear bearing retainer from the manual transmission case.


Hide 33111R 27.REMOVE OUTPUT SHAFT REAR BEARING HOLE SNAP RING

a.
C282909

Using a snap ring expander, remove the output shaft rear bearing hole snap ring from the output shaft.


Hide 33311X 28.REMOVE INPUT SHAFT REAR BEARING HOLE SNAP RING

a.
C282910

Using a snap ring expander, remove the input shaft rear bearing hole snap ring from the input shaft.


Hide 33451H 29.REMOVE REVERSE IDLER GEAR SHAFT BOLT

a.
C282911

Remove the reverse idler gear shaft bolt and the gasket from the manual transmission case.


Hide 33242E 30.REMOVE SHIFT FORK SHAFT SNAP RING

a.
C282912

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 2 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



Hide 33275C 31.REMOVE SHIFT DETENT BALL

a.
C282913

Using a 6 mm hexagon socket wrench, remove the 2 shift detent ball plugs from the manual transmission case.


b.
C282914

Using a magnet hand, remove the 2 spring seats, 2 compression springs and the 2 shift detent balls from the manual transmission case.


c.
C282915

Using a 6 mm hexagon socket wrench, remove the shift detent ball plug from the transaxle case.


d.
C282916

Using a magnet hand, remove the spring seat, compression spring and the shift detent ball from the transaxle case.


Hide 33290 32.REMOVE NO. 1 LOCK BALL ASSEMBLY

a.
C282917

Using a 6 mm hexagon socket wrench, remove the No. 1 lock ball assembly from the manual transmission case.


Hide 33111 33.REMOVE MANUAL TRANSMISSION CASE

a.
C261397

Remove the 3 bolts from the transaxle case.


b.
C282918C01
0.396,1.76 0.708,1.542 true 0.24,1.677 0.552,1.833 0.313,0.156 10 false *1
*1 Clutch Tube Bracket


Remove the 13 bolts and the clutch tube bracket from the manual transmission case.


c.
C282919

Using a brass bar and a hammer, carefully tap the projections of the manual transmission case to remove the manual transmission case from the transaxle case.

NOTICE:

Do not damage the manual transmission case and the transaxle case.



Hide 33402 34.REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C282920

Remove the reverse idler gear sub-assembly, reverse idler thrust washer and the reverse idler gear shaft from the transaxle case.


Hide 33240 35.REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
C282921

Remove the 2 bolts and the reverse shift arm bracket assembly from the transaxle case.


Hide 33243A 36.REMOVE NO. 2 GEAR SHIFT FORK SHAFT

a.
C282922

Remove the No. 2 gear shift fork set bolt and the No. 1 gear shift head set bolt from the No. 2 gear shift fork and the No. 1 gear shift head.


b.
C282923C01
1.76,0.438 2.542,0.438 true 1.271,1.927 1.563,1.375 true 1.177,1.927 1.49,2.125 0.313,0.198 10 false *1 2.573,0.354 2.885,0.552 0.313,0.198 10 false *2
*1 No. 1 Gear Shift Head
*2 No. 2 Gear Shift Fork Shaft


Remove the No. 2 gear shift fork shaft and the No. 1 gear shift head from the transaxle case.


Hide 33242 37.REMOVE NO. 1 GEAR SHIFT FORK SHAFT

a.
C282924

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



b.
C282925C01
1.896,0.667 2.76,0.25 true 2.802,0.156 3.115,0.354 0.313,0.198 10 false *1
*1 No. 1 Gear Shift Fork Shaft


Remove the No. 1 gear shift fork set bolt and the No. 1 gear shift fork shaft from the No. 1 gear shift fork.


c.
C282926C01
1.896,1.427 2.594,0.51 true 2.625,0.385 2.938,0.583 0.313,0.198 10 false *1
*1 No. 1 Gear Shift Fork


Remove the No. 1 gear shift fork.


Hide 33244G 38.REMOVE NO. 3 GEAR SHIFT FORK SHAFT

a.
C282927

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



b.
C282928C01
2.01,0.271 2.344,0.271 true 2.198,0.583 2.448,0.583 false 2.271,1.219 2.99,1.219 true 2.385,0.167 2.698,0.365 0.313,0.198 10 false *1 2.5,0.5 2.813,0.698 0.313,0.198 10 false *2 3.031,1.125 3.344,1.323 0.313,0.198 10 false *3
*1 No. 3 Gear Shift Fork Shaft
*2 No. 2 Gear Shift Fork
*3 Reverse Shift Fork


Remove the No. 3 gear shift fork shaft together with the reverse shift fork and the No. 2 gear shift fork from the transaxle case.


c.
C282929

Using a magnet hand, remove the 2 reverse shift fork balls from the reverse shift fork.


d.
C282930

Secure the No. 3 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Using 2 screwdrivers and a hammer, tap out the shift fork shaft snap ring from the No. 3 gear shift fork shaft.

HINT:

Use a piece of cloth to keep the shift fork shaft snap ring from flying off.



f.

Remove the reverse shift fork from the No. 3 gear shift fork shaft.


Hide 39.REMOVE INPUT SHAFT ASSEMBLY

a.
C282931

Remove the input shaft assembly and the output shaft assembly from the transaxle case.


Hide 40.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C282932

Remove the differential case assembly from the transaxle case.


Hide 33125 41.REMOVE MANUAL TRANSAXLE CASE RECEIVER

a.
C282933

Remove the bolt and the manual transaxle case receiver from the transaxle case.


Hide 33280 42.REMOVE REVERSE RESTRICT PIN ASSEMBLY

a.
C282934

Using a 6 mm hexagon socket wrench, remove the reverse restrict pin plug from the manual transmission case.


b.
C282935

Using a 5 mm pin punch and a hammer, drive out the slotted spring pin and remove the reverse restrict pin assembly from the manual transmission case.


Hide 33124C 43.REMOVE NO. 1 OIL RECEIVER PIPE

a.
C282936

Remove the bolt and the No. 1 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 1 oil receiver pipe.



Hide 33124D 44.REMOVE NO. 2 OIL RECEIVER PIPE

a.
C282937

Remove the bolt and the No. 2 oil receiver pipe from the manual transmission case.

NOTICE:

Do not damage the No. 2 oil receiver pipe.



Hide 33326 45.REMOVE BEARING LOCK PLATE

a.
C282938

Remove the bolt and the bearing lock plate from the transaxle case.


Hide 33449 46.REMOVE TRANSMISSION MAGNET

a.
C282939

Remove the transmission magnet from the transaxle case.


Hide 33311A 47.REMOVE INPUT SHAFT FRONT BEARING

a.
C287903C01
1.01,1.042 1.594,1.271 false 0.698,0.958 1.156,1.156 0.458,0.198 10 false SST 0.521,0.521 0.833,0.719 0.313,0.198 10 false *a 2.375,1.198 2.688,1.396 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the input shaft front bearing from the transaxle case.

SST
09612-65014  (09612-01050, 09612-01060)


Hide 31105D 48.REMOVE FRONT TRANSAXLE CASE OIL SEAL

a.
C267940C01
1.24,1.156 0.417,0.688 true 0.24,0.563 0.427,0.729 0.188,0.167 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the front transaxle case oil seal from the transaxle case.

NOTICE:

Make sure not to damage the inside of the transaxle case.



Hide 33321N 49.REMOVE OUTPUT SHAFT FRONT BEARING

a.
C282942E01
0.823,0.458 1.521,0.698 false 0.5,0.375 0.958,0.573 0.458,0.198 10 false SST

Using SST, remove the output shaft front bearing from the transaxle case.

SST
09308-00010  

NOTICE:

Do not apply excessive force to the transaxle case when using SST.



Hide 33134B 50.REMOVE OUTPUT SHAFT COVER

a.
C282943

Remove the output shaft cover from the transaxle case.


Hide 41311E 51.REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C287905C01
0.615,1.823 1.042,1.5 true 0.302,1.74 0.76,1.938 0.458,0.198 10 false SST 0.625,0.583 0.938,0.781 0.313,0.198 10 true *a 1.667,0.74 1.979,0.938 0.313,0.198 10 true *b
*a Hold
*b Turn


Using SST, remove the front differential case front tapered roller bearing (outer race) and the front differential case front plate washer from the transaxle case.

SST
09612-65014  (09612-01040, 09612-01050)


b.
C287906C02
1.75,1.25 2.5,1.26 2.5,1.26 1.802,1.313 true 2.104,1.49 2.51,1.26 2.51,1.26 2.052,0.813 false 2.542,1.188 3,1.385 0.458,0.198 10 false SST 0.583,0.938 0.896,1.135 0.313,0.198 10 false *a 2.594,0.583 2.906,0.781 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the front differential case front tapered roller bearing (inner race) from the differential case assembly.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00360)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 43410M 52.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C282946E01
1.594,1.479 1.26,1.24 1.26,1.24 1.698,0.938 true 0.896,1.135 1.208,1.365 0.313,0.229 10 true SST

Using SST and a hammer, drive out the front drive shaft oil seal RH from the transaxle case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07150)


Hide 41311F 53.REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C287908C01
0.802,0.823 1.167,1.083 true 0.51,0.74 0.844,1.031 0.333,0.292 10 false SST 0.677,0.438 1.01,0.729 0.333,0.292 10 false *a 1.865,0.521 2.198,0.813 0.333,0.292 10 false *b
*a Hold
*b Turn


Using SST, remove the front differential case rear tapered roller bearing (outer race) and the front differential case rear plate washer from the manual transmission case.

SST
09612-65014  (09612-01040, 09612-01050)


b.
C287907C02
1.896,1.521 2.719,1.708 2.719,1.708 2.5,1.448 true 2.771,1.677 3.229,1.875 0.458,0.198 10 false SST 0.208,0.521 0.667,0.719 0.458,0.198 10 false *a 2.365,0.438 2.823,0.635 0.458,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the front differential case rear tapered roller bearing (inner race) from the differential case assembly.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00360)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 43420H 54.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C282949E01
1.625,1.375 1.219,0.333 1.219,0.333 1.708,0.552 true 0.917,0.24 1.375,0.438 0.458,0.198 10 false SST

Using SST and a hammer, drive out the front drive shaft oil seal LH from the manual transmission case.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07150)


Hide 33261H 55.REMOVE SHIFT AND SELECT LEVER SHAFT OIL SEAL

a.
C121110

Using a screwdriver and a hammer, remove the shift and select lever shaft oil seal from the manual transmission case.


Hide 33261L 56.REMOVE SHIFT AND SELECT LEVER SHAFT BUSH

a.
C121111E01
1.219,1.073 2.458,0.979 2.458,0.979 2.125,0.667 true 2.542,0.938 2.917,1.135 0.375,0.198 10 false SST

Using SST and a plastic hammer, remove the shift and select lever shaft bush from the manual transmission case.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07200)