Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › INPUT SHAFT
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0094356 INPUT SHAFT A

C54 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT 4TH GEAR THRUST CLEARANCE

a.
C282989

Using a feeler gauge, measure the 4th gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 4th gear or input shaft rear radial ball bearing.


Hide 2.INSPECT 3RD GEAR THRUST CLEARANCE

a.
C282990

Using a dial indicator, measure the 3rd gear thrust clearance.

Standard clearance:

0.10 to 0.35 mm (0.00394 to 0.0137 in.)


Maximum clearance:

0.35 mm (0.0137 in.)


If the clearance exceeds the maximum, replace the No. 2 transmission clutch hub, 3rd gear or input shaft.


Hide 3.INSPECT 4TH GEAR RADIAL CLEARANCE

a.
C282991

Using a dial indicator, measure the 4th gear radial clearance between the gear and input shaft.

Standard clearance:

0.009 to 0.050 mm (0.000355 to 0.00196 in.)


Maximum clearance:

0.050 mm (0.00196 in.)


If the clearance exceeds the maximum, replace the 4th gear, 4th gear needle roller bearing or input shaft.


Hide 4.INSPECT 3RD GEAR RADIAL CLEARANCE

a.
C282992

Using a dial indicator, measure the 3rd gear radial clearance.

Standard clearance:

0.015 to 0.058 mm (0.000591 to 0.00228 in.)


Maximum clearance:

0.058 mm (0.00228 in.)


If the clearance exceeds the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft.


Hide 33334 5.REMOVE 4TH GEAR

a.
C282993

Using 2 screwdrivers and a hammer, remove the input shaft rear bearing shaft snap ring from the input shaft.

HINT:

Use a piece of cloth to keep the input shaft rear bearing shaft snap ring from flying off.



b.
C282994
2.24,0.771 2.677,0.771 false 2.708,0.698 3.167,0.896 0.458,0.198 10 false SST

Using SST and a press, remove the input shaft rear radial ball bearing and the 4th gear from the input shaft.

SST
09950-00020  

NOTICE:
·

Do not tighten SST excessively.

·

Support the input shaft by hand to prevent it from falling off.




Hide 33334A 6.REMOVE 4TH GEAR NEEDLE ROLLER BEARING

a.
C282995

Remove the 4th gear needle roller bearing and the 4th gear bearing spacer from the input shaft.


Hide 33368H 7.REMOVE 4TH GEAR SYNCHRONIZER RING

a.
C282996

Remove the 4th gear synchronizer ring from the No. 2 transmission clutch hub.


Hide 33333 8.REMOVE 3RD GEAR

a.
C282997

Using 2 screwdrivers and a hammer, remove the No. 2 clutch hub setting shaft snap ring from the input shaft.

HINT:

Use a piece of cloth to keep the No. 2 clutch hub setting shaft snap ring from flying off.



b.
C282998
0.896,0.771 1.292,1.156 false 0.583,0.688 1.042,0.885 0.458,0.198 10 false SST

Using SST and a press, remove the No. 2 transmission clutch hub and the 3rd gear from the input shaft.

SST
09950-00020  

NOTICE:
·

Do not tighten SST excessively.

·

Support the input shaft by hand to prevent it from falling off.




Hide 33368G 9.REMOVE 3RD GEAR SYNCHRONIZER RING

a.
C282999

Remove the 3rd gear synchronizer ring from the 3rd gear.


Hide 33333A 10.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.
C283000

Remove the 3rd gear needle roller bearing from the input shaft.


Hide 33364 11.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.
C283001

Remove the No. 2 transmission hub sleeve, 3 synchromesh shifting keys and the 3 synchromesh shifting key springs from the No. 2 transmission clutch hub.

NOTICE:

Use a piece of cloth to keep the synchromesh shifting keys and the synchromesh shifting key springs from flying off.