1.INSPECT 1ST GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 1st gear thrust clearance.
0.10 to 0.40 mm (0.00394 to 0.0157 in.)
0.40 mm (0.0157 in.)
If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear or No. 1 transmission clutch hub.
2.INSPECT 2ND GEAR THRUST CLEARANCE
Using a dial indicator, measure the 2nd gear thrust clearance.
0.10 to 0.55 mm (0.00394 to 0.0216 in.)
0.55 mm (0.0216 in.)
If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 2nd gear or 3rd driven gear.
3.INSPECT 1ST GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 1st gear radial clearance.
0.015 to 0.056 mm (0.000591 to 0.00220 in.)
0.056 mm (0.00220 in.)
If the clearance exceeds the maximum, replace the 1st gear, 1st gear needle roller bearing or output shaft.
4.INSPECT 2ND GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 2nd gear radial clearance.
0.015 to 0.056 mm (0.000591 to 0.00220 in.)
0.056 mm (0.00220 in.)
If the clearance exceeds the maximum, replace the 2nd gear, 2nd gear needle roller bearing or output shaft.
33422B
5.REMOVE 4TH DRIVEN GEAR
Using SST and a press, remove the output shaft rear bearing and the 4th driven gear from the output shaft.
33431C
6.REMOVE OUTPUT GEAR SPACER
Remove the output gear spacer from the output shaft.
33332
7.REMOVE 2ND GEAR
Using SST and a press, remove the 2nd gear and the 3rd driven gear from the output shaft.
33332B
8.REMOVE 2ND GEAR NEEDLE ROLLER BEARING
Remove the 2nd gear needle roller bearing and the 2nd gear bearing spacer from the output shaft.
33038E
9.REMOVE NO. 2 SYNCHRONIZER RING SET (FOR 2ND GEAR)
| *1 | Inner Ring |
| *2 | Middle Ring |
| *3 | Outer Ring |
Remove the No. 2 synchronizer ring set (for 2nd gear) from the output shaft.
33335
10.REMOVE 1ST GEAR
Using 2 screwdrivers and a hammer, remove the No. 1 clutch hub shaft snap ring from the output shaft.
Use a piece of cloth to keep the No. 1 clutch hub shaft snap ring from flying off.
Using SST and a press, remove the No. 1 transmission clutch hub and the 1st gear from the output shaft.
Do not tighten SST excessively.
Support the output shaft by hand to prevent it from falling off.
33367B
11.REMOVE 1ST GEAR SYNCHRONIZER RING
Remove the 1st gear synchronizer ring from the 1st gear.
33335C
12.REMOVE 1ST GEAR NEEDLE ROLLER BEARING
Remove the 1st gear needle roller bearing from the output shaft.
33348
13.REMOVE 1ST GEAR THRUST WASHER
Remove the 1st gear thrust washer from the output shaft.
33348A
14.REMOVE 1ST GEAR THRUST WASHER PIN OR BALL
Using a magnet hand, remove the 1st gear thrust washer pin or ball from the output shaft.
33331
15.REMOVE REVERSE GEAR
Remove the reverse gear, 3 synchromesh shifting keys and the 3 synchromesh shifting key springs from the No. 1 transmission clutch hub.
Use a piece of cloth to keep the synchromesh shifting keys and the synchromesh shifting key springs from flying off.