Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK(for TMMIN Made) › 2013.12–2018.01
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0105857 FRONT DOOR LOCK(for TMMIN Made) G

DOOR LOCK  FRONT DOOR LOCK(for TMMIN Made)  INSPECTION  


PROCEDURE

Hide 69320 1.INSPECT FRONT DOOR LOCK ASSEMBLY LH

a.
B359275C01
0.813,3.958 1.229,3.958 true 2.125,3.958 2.542,3.958 true 0.771,3.25 1.083,3.406 0.313,0.156 10 false *a 2.365,2.865 2.677,3.021 0.313,0.156 10 false *b 1.813,3.125 2.125,3.281 0.313,0.156 10 false *c 2.615,3.854 2.927,4.052 0.313,0.198 10 false UL 0.667,3.854 0.958,4.063 0.292,0.208 10 false L
*a Component without harness connected (Front Door Lock Assembly LH)
*b Unlock
*c Lock


Check the operation.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locked
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocked


If the result is not as specified, replace the front door lock assembly LH.



b.
B359275C02
1.354,4.5 1.552,4.25 true 1.99,4.51 1.792,4.24 true 0.781,3.229 1.094,3.385 0.313,0.156 10 false *a 2.375,2.875 2.688,3.031 0.313,0.156 10 false *b 1.802,3.125 2.115,3.281 0.313,0.156 10 false *c 1.177,4.49 1.635,4.646 0.458,0.156 10 false LSSR 2.021,4.49 2.333,4.646 0.313,0.156 10 false E
*a Component without harness connected (Front Door Lock Assembly LH)
*b Unlock
*c Lock


Check the resistance of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
7 (E) - 8 (LSSR) Locked 10 kΩ or higher
7 (E) - 8 (LSSR) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.



c.
B359277C01
1.167,4.25 1.385,3.958 true 1.729,4.25 1.594,3.948 true 1.979,4.24 1.844,3.938 true 0.979,3.125 1.292,3.281 0.313,0.156 10 false *a 1.917,0.667 2.229,0.823 0.313,0.156 10 false *b 2.458,0.396 2.771,0.552 0.313,0.156 10 false *c 3.135,0.49 3.396,0.667 0.26,0.177 10 false *d 1.083,4.271 1.396,4.427 0.313,0.156 10 false UL 1.729,4.271 2.042,4.427 0.313,0.156 10 false L 1.99,4.26 2.302,4.417 0.313,0.156 10 false E
*a Component without harness connected (Front Door Lock Assembly LH)
*b Lock
*c Off
*d Unlock


Check the resistance of the lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (L) - 7 (E) Locked Below 1 Ω
9 (L) - 7 (E) Off 10 kΩ or higher
10 (UL) - 7 (E) Unlocked Below 1 Ω
10 (UL) - 7 (E) Off 10 kΩ or higher


If the result is not as specified, replace the front door lock assembly LH.



Hide 69310 2.INSPECT FRONT DOOR LOCK ASSEMBLY RH

a.
B359276C01
0.823,3.958 1.24,3.958 true 2.125,3.958 2.542,3.958 true 0.792,3.271 1.104,3.427 0.313,0.156 10 false *a 0.917,2.844 1.229,3 0.313,0.156 10 false *b 1.469,3.104 1.781,3.26 0.313,0.156 10 false *c 0.688,3.854 1,4.01 0.313,0.156 10 false L 2.625,3.885 2.938,4.042 0.313,0.156 10 false UL
*a Component without harness connected (Front Door Lock Assembly RH)
*b Unlock
*c Lock


Check the operation.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locked
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocked


If the result is not as specified, replace the front door lock assembly RH.



b.
B359276C02
1.396,4.5 1.552,4.25 true 1.958,4.5 1.781,4.229 true 0.833,3.313 1.146,3.469 0.313,0.156 10 false *a 0.896,2.833 1.208,2.99 0.313,0.156 10 false *b 1.49,3.094 1.802,3.25 0.313,0.156 10 false *c 1.281,4.49 1.5,4.667 0.219,0.177 10 false E 1.802,4.49 2.229,4.656 0.427,0.167 10 false LSSR
*a Component without harness connected (Front Door Lock Assembly RH)
*b Unlock
*c Lock


Check the resistance of the unlock detection switch. (w/ Unlock Detection Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Locked 10 kΩ or higher
7 (LSSR) - 8 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.