Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK(for TMMIN Made) › 2013.12–2018.01
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0105858 REAR DOOR LOCK(for TMMIN Made) G

DOOR LOCK  REAR DOOR LOCK(for TMMIN Made)  INSPECTION  


PROCEDURE

Hide 69340 1.INSPECT REAR DOOR LOCK ASSEMBLY LH

a.
B359290C01
0.865,3.719 1.281,3.719 true 2.188,3.708 2.604,3.708 true 0.844,3.094 1.156,3.25 0.313,0.156 10 false *a 1.552,2.865 1.865,3.021 0.313,0.156 10 false *b 0.885,2.771 1.198,2.927 0.313,0.156 10 false *c 0.698,3.635 1.01,3.792 0.313,0.156 10 false L 2.688,3.615 3,3.771 0.313,0.156 10 false UL
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Unlock
*c Lock


Check the operation.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locked
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocked


If the result is not as specified, replace the rear door lock assembly LH.



b.
B359290C02
1.25,4.354 1.458,4.021 true 2.198,4.385 2,4.031 true 0.885,3.073 1.198,3.229 0.313,0.156 10 false *a 1.552,2.885 1.865,3.042 0.313,0.156 10 false *b 0.885,2.781 1.198,2.938 0.313,0.156 10 false *c 1.188,4.375 1.469,4.573 0.281,0.198 10 false E 2.042,4.406 2.5,4.625 0.458,0.219 10 false LSSR
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Unlock
*c Lock


Check the resistance. (w/ Unlock Detection Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock assembly LH.



Hide 69330 2.INSPECT REAR DOOR LOCK ASSEMBLY RH

a.
B359291C01
0.865,3.719 1.281,3.719 true 2.177,3.719 2.594,3.719 true 0.844,3.063 1.156,3.219 0.313,0.156 10 false *a 1.896,2.906 2.208,3.063 0.313,0.156 10 false *b 2.573,2.802 2.885,2.958 0.313,0.156 10 false *c 0.708,3.625 1.021,3.781 0.313,0.156 10 false L 2.688,3.615 3,3.771 0.313,0.156 10 false UL
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Unlock
*c Lock


Check the operation.

i.

Apply battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Locked
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlocked


If the result is not as specified, replace the rear door lock assembly RH.



b.
B359291C02
1.229,4.365 1.458,4.021 true 2.229,4.385 2,4.021 true 0.906,3.083 1.219,3.24 0.313,0.156 10 false *a 1.906,2.885 2.219,3.042 0.313,0.156 10 false *b 2.563,2.792 2.875,2.948 0.313,0.156 10 false *c 1.167,4.375 1.427,4.604 0.26,0.229 10 false E 2.083,4.396 2.521,4.625 0.438,0.229 10 false LSSR
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Unlock
*c Lock


Check the resistance. (w/ Unlock Detection Switch)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock assembly RH.