Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK(for TMMIN Made) › 2013.12–2018.01
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0105858 REAR DOOR LOCK(for TMMIN Made) A

DOOR LOCK  REAR DOOR LOCK(for TMMIN Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 69770B 1.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Power Door Lock)

a.

Engage the guide and install the rear door inside locking cable assembly to the rear door lock assembly.


b.
B359288

Engage the 3 claws and close the cover.


Hide 69770B 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Power Door Lock)

a.

Engage the guide and install the rear door inside locking cable assembly to the rear door lock assembly.


Hide 69730D 3.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Power Door Lock)

a.

Engage the guide and install the rear door lock remote control cable assembly to the rear door lock assembly.


b.
B359285

Engage the claw and close the cover.


Hide 69730D 4.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Power Door Lock)

a.

Engage the guide and install the rear door lock remote control cable assembly to the rear door lock assembly.


Hide 69330 5.INSTALL REAR DOOR LOCK ASSEMBLY (w/ Power Door Lock)

NOTICE:
·

When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the rear door lock assembly.



a.

Apply MP grease to the sliding parts of the rear door lock assembly.


b.

When reusing the rear door lock assembly:

i.

Install a new door lock wiring harness seal to the rear door lock assembly.



c.
B359282

Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.


d.

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.


e.

Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 69330 6.INSTALL REAR DOOR LOCK ASSEMBLY (w/o Power Door Lock)

a.

Apply MP grease to the sliding parts of the rear door lock assembly.


b.
B365431

Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.


c.

Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.


d.

Using a T30 "TORX" socket wrench, install the rear door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 68103 7.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

Hide 67407H 8.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 67871 9.CONNECT REAR DOOR WEATHERSTRIP

a.

Connect the upper part of rear door weatherstrip.


Hide 67841E 10.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 68142C 11.INSTALL REAR DOOR GLASS RUN

Hide 68173B 12.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

Hide 67603 13.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 74271A 14.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)

Hide 74271A 15.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)

Hide 69260E 16.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Power Window)

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)