Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › from 2013.12
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0092579 FRONT SEAT OUTER BELT ASSEMBLY N

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a front seat outer belt assembly that has an unactivated pretensioner.

·

The seat belt pretensioner produces a loud, exploding sound when it activates. Perform the operation outside and where it will not be a nuisance to persons nearby.

·

When activating a front seat outer belt assembly (with seat belt pretensioner), stand at least 10 m (32.8 ft.) away from the front seat outer belt assembly.

·

When activating the seat belt pretensioner, always use the specified SST (SRS airbag deployment tool).

·

The seat belt pretensioner becomes extremely hot when the front seat outer belt assembly is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a front seat outer belt assembly with an activated pretensioner.

·

Do not apply water, etc. to a front seat outer belt assembly that has an activated pretensioner.

·

Always wash your hands with water after completing the activation.



HINT:

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a front seat outer belt assembly (with a seat belt pretensioner), always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the service dept. of the distributor.


Hide 73220 2.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Installed in Vehicle)

a.
C110371E24
0.969,1.229 0.74,0.771 false 0.427,0.667 0.802,0.865 0.375,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.


i.
C110372C26
2.708,0.74 2.51,0.74 false 0.969,1.552 0.469,1.219 false 0.146,1.104 0.458,1.302 0.313,0.198 10 false SST 2.781,0.625 3,0.823 0.219,0.198 10 false *a
*a Battery


Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
C110475E01
1.085,0.17 1.442,0.371 0.358,0.201 10 SST 1.773,0.634 1.455,0.316 false

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:
·

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.





b.

Disconnect SST from the battery.


c.

Disconnect the seat belt pretensioner connector.

i.

Remove the center pillar lower garnish.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


ii.

Disconnect the seat belt pretensioner connector.

B364559C02
0.583,1.833 0.865,1.833 true 1.281,2.281 0.948,2.198 true 4.177,1.833 4.458,1.833 true 4.854,2.281 4.521,2.198 true 3.5,2.792 3.5,0 false 0.156,0.104 0.667,0.479 0.51,0.375 12 false *A 3.646,0.104 4.083,0.396 0.438,0.292 12 false *B 1.323,2.229 1.635,2.385 0.313,0.156 10 false *1 0.406,1.719 0.719,1.875 0.313,0.156 10 false *a 4.896,2.219 5.208,2.375 0.313,0.156 10 false *1 4,1.719 4.313,1.875 0.313,0.156 10 false *a
*A for TMT Made *B for TMMIN Made
*1 Locking Button - -
*a Protective Tape - -


1.

Using a screwdriver with its tip wrapped in protective tape, release the locking button.

2.

Disconnect the seat belt pretensioner connector.




d.
B349261N01
0.865,1.563 0.865,1.313 false 2.177,1.563 2.177,1.313 false 0.74,1.583 1.063,1.76 0.323,0.177 10 false SST 2.042,1.583 2.365,1.76 0.323,0.177 10 false SST

Connect SST.

i.

Connect 2 SST and then connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00770  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.
C154370C14
0.438,1.188 0.927,1.406 false 1.76,0.563 2.052,0.292 false 2.073,0.188 2.417,0.385 0.344,0.198 10 false *a 0.115,1.083 0.51,1.302 0.396,0.219 10 false SST 1.323,1.813 2.271,2.01 0.948,0.198 10 false 10 m or more
*a Battery


Move SST at least 10 m (32.8 ft.) away from the front of the vehicle.


iii.

Close all the doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.




e.

Deploy the seat belt pretensioner.

i.

Confirm that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




f.

Dispose of the front seat outer belt assembly.

i.

Remove the front seat outer belt assembly and SST.


ii.

Place the front seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it according to local regulations.

CAUTION:
·

The front seat outer belt assembly becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.



HINT:

When scrapping a vehicle, deploy the seat belt pretensioner, and then scrap the vehicle with the front seat outer belt assembly installed.




Hide 73220 3.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Not Installed in Vehicle)

CAUTION:
·

Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.



NOTICE:
·

When disposing of a front seat outer belt assembly with a pretensioner, never deploy the seat belt pretensioner in the customer's vehicle.

·

Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.

·

The front seat outer belt assembly produces an exploding sound when the pretensioner deploys, so perform the operation outdoors and where it will not disturb local residents.

·

When deploying a seat belt pretensioner, perform the operation at least 10 m (32.8 ft.) away from the front seat outer belt assembly.

·

Be sure to follow the procedure listed below when deploying a seat belt pretensioner.



a.

Remove the front seat outer belt assembly.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


b.
B343493C01
1.229,0.49 1.542,0.646 0.313,0.156 10 false *a 2.24,0.875 2.875,1.115 0.635,0.24 10 false 100 mm
*a Cut


Wind the front seat outer belt assembly webbing with the retractor.


c.

When the front seat outer belt assembly webbing is sufficiently wound, cut the front seat outer belt assembly webbing approximately 100 mm (3.94 in.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in correlation with how much the front seat outer belt assembly webbing is wound.



d.
C110371E24
0.969,1.229 0.74,0.771 false 0.427,0.667 0.802,0.865 0.375,0.198 10 false SST

Check whether SST is functioning.

SST
09082-00700  

CAUTION:

Always use the specified SST when activating the seat belt pretensioner.


i.
C110372C28
2.708,0.74 2.51,0.74 false 0.969,1.552 0.469,1.219 false 0.146,1.104 0.458,1.302 0.313,0.198 10 false SST 2.781,0.625 3,0.823 0.219,0.198 10 false *a
*a Battery


Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

HINT:

Do not connect the yellow connector. The yellow connector is for connections to the seat belt pretensioner.



ii.
C110475E01
1.085,0.17 1.442,0.371 0.358,0.201 10 SST 1.773,0.634 1.455,0.316 false

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




e.

Disconnect SST from the battery.


f.
B349261N01
0.865,1.563 0.865,1.313 false 2.177,1.563 2.177,1.313 false 0.74,1.583 1.063,1.76 0.323,0.177 10 false SST 2.042,1.583 2.365,1.76 0.323,0.177 10 false SST

Connect SST.

i.

Connect 2 SST and then connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00770  

NOTICE:

Do not lock the secondary lock of the twin lock to avoid damaging the SST connector and wire harness.



ii.
B104882C37
2.292,0.938 1.823,0.448 false 2.656,1.469 2.896,1.646 0.24,0.177 10 false *b 1.635,0.333 1.844,0.521 0.208,0.188 10 false *a
*a Stripped Wire Section
*b Wire Diameter


Using braided wire, tie down the seat belt pretensioner to an unneeded tire and disc wheel.

Wire:

Stripped wire cross sectional area 1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire is too thin or an alternative object is used to tie down the seat belt assembly pretensioner, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the cross sectional area of the stripped wire: Cross sectional area = 3.14 x (Diameter)2 / 4



iii.
B345171E01
1.49,1.177 1.344,1.448 false 2.146,1.927 1.813,1.927 false 1.188,1.479 1.646,1.677 0.458,0.198 10 false SST 1.51,1.854 1.969,2.052 0.458,0.198 10 false SST

Place the front seat outer belt assembly on the ground and cover it with a tire and disc wheel.

NOTICE:
·

Position the front seat outer belt assembly as shown in the illustration.

·

The tire and disc wheel may be damaged by the seat belt pretensioner deployment, so use an unneeded tire and disc wheel.




iv.

Position and hold SST at least 10 m (32.8 ft.) away from the disc wheel.

NOTICE:

Do not damage the SST wire harness.




g.
B169424C05
1.635,0.885 1.885,0.885 false 0.604,4.281 0.604,4.083 false 1.958,3.906 2.865,4.094 0.906,0.188 10 false 10 m or more 0.469,4.313 0.802,4.479 0.333,0.167 10 false SST 1.906,0.771 2.094,0.938 0.188,0.167 10 false *a
*a Battery


Deploy the seat belt pretensioner.

i.

Check that no one is within a 10 m (32.8 ft.) radius of the disc wheel.


ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




h.

Dispose of the front seat outer belt assembly.

i.

Remove the tire and disc wheel and SST.


ii.

Place the front seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it according to local regulations.

CAUTION:
·

The front seat outer belt assembly becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.