Home › Engine / Hybrid System › 2NZ-FE FUEL › FUEL TANK(for TMMIN Made) › 2013.12–2016.10
RM30M0E _51 Engine / Hybrid System _017076 2NZ-FE FUEL _0106429 FUEL TANK(for TMMIN Made) A

2NZ-FE FUEL  FUEL TANK(for TMMIN Made)  REMOVAL  


PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 2.DRAIN FUEL

Hide 57533B 4.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 5.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58156 6.REMOVE NO. 4 FRONT FLOOR HEAT INSULATOR

a.
A313093

Remove the 2 nuts and No. 4 front floor heat insulator from the vehicle.


Hide 77641A 7.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A305619

Remove the bolt, clip and No. 1 fuel tank protector from the vehicle.


Hide 46420 8.SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.
A300032

Remove the 2 bolts to separate the No. 2 parking brake cable assembly from the vehicle.


Hide 77028F 9.DISCONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A300033

Slide the hose clip and disconnect the No. 2 fuel emission tube sub-assembly from the fuel tank to canister tube.


Hide 77209F 10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A313096C01
2.552,2.521 2.729,2.271 false 0.969,2.479 0.76,2.25 false 2.115,2.531 1.906,2.302 false 2.208,4.083 2.385,3.833 true 1.177,3.76 0.969,3.531 false 2.333,4.5 2.615,4.5 false 2.375,4.365 2.625,4.198 false 1.677,4.135 1.906,3.771 1.906,3.771 1.823,4.146 true 2.781,2.177 3.094,2.333 0.313,0.156 10 false *1 0.573,2.177 0.885,2.333 0.313,0.156 10 false *2 2.656,4.438 2.969,4.594 0.313,0.156 10 false *3 2.698,4.104 3.01,4.26 0.313,0.156 10 false *4 0.792,3.438 1.104,3.594 0.313,0.156 10 false *5 1.969,3.667 2.281,3.823 0.313,0.156 10 false *6 1.729,2.167 2.042,2.323 0.313,0.156 10 false *1 2.438,3.771 2.75,3.927 0.313,0.156 10 false *1
*1 Retainer
*2 Fuel Tube Connector Cover
*3 Fuel Tube Connector
*4 Fuel Pipe
*5 Nylon Tube
*6 O-ring
V100135

Pull
V100136

Pinch
V100137

Pull Out


Release the lock of the fuel tube connector cover as shown in the illustration, then pull out the fuel tank main tube sub-assembly.

NOTICE:
·

If the fuel tube connector and fuel main tube are stuck together, push in and pull out the fuel tube connector while squeezing the fuel main tube to release the connection, and then disconnect the fuel tube connector.

·

Clean away any dirt or foreign matter from the fuel tube connector before performing the operation.

·

The fuel tube connector and fuel main tube are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.

·

Do not use any tools.

·

After disconnecting the fuel tube connector, check that there is no foreign matter on the seal surface of the fuel main tube.

·

After disconnecting the fuel tank main tube sub-assembly, protect the contact surfaces by covering them with a plastic bag.

·

Do not bend or twist the tubes.




Hide 77701W 11.DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A304791C01
1.729,1.24 1.927,1.01 true 1.552,1.177 1.865,1.375 0.313,0.198 10 false *1
*1 No. 6 Fuel Tank Breather Tube


Disconnect the No. 1 canister outlet hose sub-assembly from the No. 6 fuel tank breather tube.


Hide 12.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A304792C01
1.885,0.75 2.823,0.302 true 2.854,0.198 3.167,0.396 0.313,0.198 10 false *1
*1 Fuel Tank Breather Tube Connector


Loosen the hose clamp and disconnect the fuel tank breather tube sub-assembly from the fuel tank breather tube connector.


Hide 77213B 13.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A304793

Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77100 14.REMOVE FUEL TANK ASSEMBLY

a.

Using an engine lifter, support the fuel tank assembly.


b.
A300037

Remove the 4 bolts and fuel tank assembly from the vehicle.

NOTICE:

Make sure that the fuel tank assembly does not fall.



Hide 77209F 15.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A300035

Disengage the 2 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77028F 16.REMOVE NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A300036

Disengage the 2 clamps to remove the No. 2 fuel emission tube sub-assembly from the fuel tank assembly.


Hide 77701W 17.REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A305547

Disengage the 2 clamps to remove the No. 1 canister outlet hose sub-assembly from the fuel tank assembly.