Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.12–2016.04
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B161C/9A  Lost Communication with Front Satellite Sensor Bus Center  B161D/9A  Front Satellite Sensor Bus Center Initialization Incomplete  


DESCRIPTION

The front airbag sensor circuit consists of the airbag ECU assembly and front airbag sensor.

The front airbag sensor detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B161C/9A Lost Communication with Front Satellite Sensor Bus Center
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor circuit.

·

Front airbag sensor malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor

·

Airbag ECU assembly


DTC does not correspond to check mode.
B161D/9A Front Satellite Sensor Bus Center Initialization Incomplete
·

The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the front airbag sensor circuit.

·

Front airbag sensor malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor

·

Airbag ECU assembly


DTC does not correspond to check mode.

WIRING DIAGRAM

C292134
1.323,1.406 1.781,1.604 0.458,0.198 10 false +SL 1.375,3.073 1.833,3.271 0.458,0.198 10 false -SL 1.698,1.302 2.156,1.5 0.458,0.198 10 false 2 1.708,2.958 2.167,3.156 0.458,0.198 10 false 1 2.75,0.479 3.208,0.677 0.458,0.198 10 false *2 4.333,0.479 4.792,0.677 0.458,0.198 10 false *2 4.333,2.135 4.792,2.333 0.458,0.198 10 false *2 2.75,2.135 3.208,2.333 0.458,0.198 10 false *2 4.333,1.313 4.792,1.51 0.458,0.198 10 false *1 4.333,2.969 4.792,3.167 0.458,0.198 10 false *1 2.75,2.969 3.208,3.167 0.458,0.198 10 false *1 2.75,1.313 3.208,1.51 0.458,0.198 10 false *1 3.375,0.573 3.833,0.771 0.458,0.198 10 false AF6 3.375,2.229 3.833,2.427 0.458,0.198 10 false AF6 3.375,1.396 3.833,1.594 0.458,0.198 10 false AF3 3.375,3.052 3.833,3.25 0.458,0.198 10 false AF3 3.458,1.198 3.917,1.396 0.458,0.198 10 false 1 3.458,2.865 3.917,3.063 0.458,0.198 10 false 2 5.604,1.396 6.063,1.594 0.458,0.198 10 false +SL 5.604,3.052 6.063,3.25 0.458,0.198 10 false -SL 5.344,1.302 5.802,1.5 0.458,0.198 10 false 30 5.344,2.958 5.802,3.156 0.458,0.198 10 false 28 0.427,3.448 0.885,3.646 0.458,0.198 10 false A27 0.438,3.594 2,3.844 1.563,0.25 10 false Front Airbag Sensor 5.49,3.448 5.948,3.646 0.458,0.198 10 false F21 5.479,3.604 7.031,3.833 1.552,0.229 10 false Airbag ECU Assembly 2.25,4 3.667,4.333 1.417,0.333 10 false *1: for TMT Made 2.25,4.333 3.75,4.552 1.5,0.219 10 false *2: for TMMIN Made 3.458,0.375 3.917,0.573 0.458,0.198 10 false 1 3.469,2.042 3.927,2.24 0.458,0.198 10 false 2

PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and front airbag sensor. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the connector terminals are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT AIRBAG SENSOR CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

2.CHECK FRONT AIRBAG SENSOR CIRCUIT (OPEN)
a.
C281395C08
1,0.583 1.469,0.833 0.469,0.25 0.417,3.583 0.917,3.833 0.5,0.25 2.052,1.333 2.302,0.948 true 2.74,1.333 2.531,0.948 true 2.385,1.458 2.417,1.208 false 0.958,4.198 1.25,3.75 true 1.719,4.208 1.479,3.75 true 0.406,2.125 0.719,2.281 0.313,0.156 10 false *1 2.813,2.26 3.125,2.417 0.313,0.156 10 false *2 2.313,1.469 2.573,1.698 0.26,0.229 10 false *3 1,0.281 1.313,0.438 0.313,0.156 10 false *a 0.719,2.125 0.896,2.292 0.177,0.167 10 false F 2.385,2.115 2.563,2.281 0.177,0.167 10 false A 1.021,2.125 1.198,2.292 0.177,0.167 10 false E 1.469,2.125 1.646,2.292 0.177,0.167 10 false D 1.625,2.125 1.802,2.292 0.177,0.167 10 false C 1.125,0.615 1.438,0.771 0.313,0.156 10 false F21 2.073,2.125 2.229,2.323 0.156,0.198 10 false B 0.552,3.615 1.01,3.813 0.458,0.198 10 false A27 1.823,1.25 2.281,1.448 0.458,0.198 10 false -SL 2.781,1.24 3.24,1.438 0.458,0.198 10 false +SL 0.417,3.24 0.729,3.438 0.313,0.198 10 false *b 0.729,4.135 1.188,4.333 0.458,0.198 10 false -SL 1.771,4.115 2.229,4.313 0.458,0.198 10 false +SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor)


Connect the connectors that link the engine room main wire and instrument panel wire.


b.

Using a Service Wire, connect terminals 28 (-SL) and 30 (+SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 (+SL) - A27-1 (-SL) Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for TMT Made) B
NG (for TMMIN Made) C



A

3.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT)

B

13.CHECK INSTRUMENT PANEL WIRE (OPEN)

C

14.CHECK INSTRUMENT PANEL WIRE (OPEN)
3.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT)
a.
C281396C09
0.323,2.229 0.823,2.479 0.5,0.25 0.979,2.875 1.208,2.396 true 1.667,2.865 1.438,2.375 true 0.385,0.625 0.698,0.781 0.313,0.156 10 false *1 2.76,0.792 3.073,0.948 0.313,0.156 10 false *2 0.188,1.688 0.5,1.844 0.313,0.156 10 false *a 0.656,0.615 0.906,0.844 0.25,0.229 10 false F 2.333,0.615 2.583,0.844 0.25,0.229 10 false A 0.969,0.625 1.219,0.854 0.25,0.229 10 false E 1.417,0.615 1.667,0.844 0.25,0.229 10 false D 1.573,0.615 1.823,0.844 0.25,0.229 10 false C 2.021,0.615 2.229,0.854 0.208,0.24 10 false B 0.448,2.271 0.906,2.469 0.458,0.198 10 false A27 0.75,2.792 1.208,2.99 0.458,0.198 10 false -SL 1.708,2.771 2.167,2.969 0.458,0.198 10 false +SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 (+SL) - A27-1 (-SL) Always 1 MΩ or higher



Result:
Result Proceed to
OK A
NG (for TMT Made) B
NG (for TMMIN Made) C



A

4.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO B+)

B

11.CHECK INSTRUMENT PANEL WIRE (SHORT)

C

12.CHECK INSTRUMENT PANEL WIRE (SHORT)
4.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.
C281396C09
0.323,2.229 0.823,2.479 0.5,0.25 0.979,2.875 1.208,2.396 true 1.667,2.865 1.438,2.375 true 0.385,0.625 0.698,0.781 0.313,0.156 10 false *1 2.76,0.792 3.073,0.948 0.313,0.156 10 false *2 0.188,1.688 0.5,1.844 0.313,0.156 10 false *a 0.656,0.615 0.906,0.844 0.25,0.229 10 false F 2.333,0.615 2.583,0.844 0.25,0.229 10 false A 0.969,0.625 1.219,0.854 0.25,0.229 10 false E 1.417,0.615 1.667,0.844 0.25,0.229 10 false D 1.573,0.615 1.823,0.844 0.25,0.229 10 false C 2.021,0.615 2.229,0.854 0.208,0.24 10 false B 0.448,2.271 0.906,2.469 0.458,0.198 10 false A27 0.75,2.792 1.208,2.99 0.458,0.198 10 false -SL 1.708,2.771 2.167,2.969 0.458,0.198 10 false +SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A27-2 (+SL) - Body ground Ignition switch ON Below 1 V
A27-1 (-SL) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


Result:
Result Proceed to
OK A
NG (for TMT Made) B
NG (for TMMIN Made) C



A

5.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

B

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

C

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
5.CHECK FRONT AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
C281396C09
0.323,2.229 0.823,2.479 0.5,0.25 0.979,2.875 1.208,2.396 true 1.667,2.865 1.438,2.375 true 0.385,0.625 0.698,0.781 0.313,0.156 10 false *1 2.76,0.792 3.073,0.948 0.313,0.156 10 false *2 0.188,1.688 0.5,1.844 0.313,0.156 10 false *a 0.656,0.615 0.906,0.844 0.25,0.229 10 false F 2.333,0.615 2.583,0.844 0.25,0.229 10 false A 0.969,0.625 1.219,0.854 0.25,0.229 10 false E 1.417,0.615 1.667,0.844 0.25,0.229 10 false D 1.573,0.615 1.823,0.844 0.25,0.229 10 false C 2.021,0.615 2.229,0.854 0.208,0.24 10 false B 0.448,2.271 0.906,2.469 0.458,0.198 10 false A27 0.75,2.792 1.208,2.99 0.458,0.198 10 false -SL 1.708,2.771 2.167,2.969 0.458,0.198 10 false +SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Airbag Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 (+SL) - Body ground Always 1 MΩ or higher
A27-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Result Proceed to
OK A
NG (for TMT Made) B
NG (for TMMIN Made) C



A

6.CHECK FRONT AIRBAG SENSOR

B

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

C

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
6.CHECK FRONT AIRBAG SENSOR
a.
C281394C04
0.552,0.813 0.865,0.969 0.313,0.156 10 false *1 2.615,0.969 2.927,1.125 0.313,0.156 10 false *2 1.438,0.823 1.625,1.052 0.188,0.229 10 false D 2.198,0.823 2.354,1.021 0.156,0.198 10 false A 2.042,0.823 2.198,1.021 0.156,0.198 10 false B 1.594,0.823 1.75,1.021 0.156,0.198 10 false C 0.979,0.823 1.135,1.021 0.156,0.198 10 false E 0.844,0.813 1,1.01 0.156,0.198 10 false F
*1 Front Airbag Sensor
*2 Airbag ECU Assembly


Connect the connector to the airbag ECU assembly.


b.

Temporarily replace the front airbag sensor with a new one.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188

Result:
Result Proceed to
DTC B161C/9A or B161D/9A is not output A
DTC B161C/9A or B161D/9A is output B


HINT:

Codes other than B161C/9A and B161D/9A may be output at this time, but they are not related to this check.


i.

Reinstall the former front airbag sensor, and connect the connector.



A

END (FRONT AIRBAG SENSOR WAS DEFECTIVE)

B

7.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C281398C03
0.333,2.25 0.833,2.5 0.5,0.25 1.094,2.896 1.354,2.313 true 1.594,2.854 1.521,2.313 true 1.896,0.615 2.063,0.323 false 1.052,1.083 1.188,0.771 false 0.365,0.615 0.677,0.771 0.313,0.156 10 false *1 2.76,0.76 3.073,0.917 0.313,0.156 10 false *2 0.938,1.115 1.25,1.271 0.313,0.156 10 false *3 2.104,0.219 2.323,0.417 0.219,0.198 10 false *4 0.188,1.719 0.5,1.875 0.313,0.156 10 false *a 0.667,0.615 0.896,0.802 0.229,0.188 10 false F 0.906,0.625 1.135,0.813 0.229,0.188 10 false E 1.354,0.625 1.583,0.813 0.229,0.188 10 false D 1.625,0.615 1.854,0.802 0.229,0.188 10 false C 2.333,0.615 2.563,0.802 0.229,0.188 10 false A 2.094,0.615 2.323,0.802 0.229,0.188 10 false B 0.938,2.885 1.396,3.083 0.458,0.198 10 false -SL 1.479,2.885 1.938,3.083 0.458,0.198 10 false +SL 0.458,2.281 0.917,2.479 0.458,0.198 10 false AF3
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF3-1 (+SL) - Body ground Always 1 MΩ or higher
AF3-2 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C292135
0.583,2.333 1.083,2.583 0.5,0.25 1.083,1.094 1.177,0.771 false 1.906,1.083 1.906,0.771 false 1.354,2.719 1.844,2.365 true 2.49,2.708 2.052,2.354 true 0.396,0.615 0.708,0.771 0.313,0.156 10 false *1 2.781,0.76 3.094,0.917 0.313,0.156 10 false *2 1.01,1.104 1.323,1.26 0.313,0.156 10 false *3 1.833,1.104 2.146,1.26 0.313,0.156 10 false *4 0.26,1.781 0.573,1.938 0.313,0.156 10 false *a 0.656,0.615 0.969,0.771 0.313,0.156 10 false F 0.906,0.615 1.219,0.771 0.313,0.156 10 false E 1.354,0.615 1.667,0.771 0.313,0.156 10 false D 2.094,0.604 2.406,0.76 0.313,0.156 10 false B 1.635,0.615 1.948,0.771 0.313,0.156 10 false C 2.344,0.604 2.656,0.76 0.313,0.156 10 false A 0.698,2.365 1.115,2.594 0.417,0.229 10 false AF6 2.542,2.635 2.958,2.865 0.417,0.229 10 false +SL 1.104,2.656 1.521,2.885 0.417,0.229 10 false -SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF6-1 (+SL) - Body ground Always 1 MΩ or higher
AF6-2 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
C281398C03
0.333,2.25 0.833,2.5 0.5,0.25 1.094,2.896 1.354,2.313 true 1.594,2.854 1.521,2.313 true 1.896,0.615 2.063,0.323 false 1.052,1.083 1.188,0.771 false 0.365,0.615 0.677,0.771 0.313,0.156 10 false *1 2.76,0.76 3.073,0.917 0.313,0.156 10 false *2 0.938,1.115 1.25,1.271 0.313,0.156 10 false *3 2.104,0.219 2.323,0.417 0.219,0.198 10 false *4 0.188,1.719 0.5,1.875 0.313,0.156 10 false *a 0.667,0.615 0.896,0.802 0.229,0.188 10 false F 0.906,0.625 1.135,0.813 0.229,0.188 10 false E 1.354,0.625 1.583,0.813 0.229,0.188 10 false D 1.625,0.615 1.854,0.802 0.229,0.188 10 false C 2.333,0.615 2.563,0.802 0.229,0.188 10 false A 2.094,0.615 2.323,0.802 0.229,0.188 10 false B 0.938,2.885 1.396,3.083 0.458,0.198 10 false -SL 1.479,2.885 1.938,3.083 0.458,0.198 10 false +SL 0.458,2.281 0.917,2.479 0.458,0.198 10 false AF3
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AF3-1 (+SL) - Body ground Ignition switch ON Below 1 V
AF3-2 (-SL) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
C292135
0.583,2.333 1.083,2.583 0.5,0.25 1.083,1.094 1.177,0.771 false 1.906,1.083 1.906,0.771 false 1.354,2.719 1.844,2.365 true 2.49,2.708 2.052,2.354 true 0.396,0.615 0.708,0.771 0.313,0.156 10 false *1 2.781,0.76 3.094,0.917 0.313,0.156 10 false *2 1.01,1.104 1.323,1.26 0.313,0.156 10 false *3 1.833,1.104 2.146,1.26 0.313,0.156 10 false *4 0.26,1.781 0.573,1.938 0.313,0.156 10 false *a 0.656,0.615 0.969,0.771 0.313,0.156 10 false F 0.906,0.615 1.219,0.771 0.313,0.156 10 false E 1.354,0.615 1.667,0.771 0.313,0.156 10 false D 2.094,0.604 2.406,0.76 0.313,0.156 10 false B 1.635,0.615 1.948,0.771 0.313,0.156 10 false C 2.344,0.604 2.656,0.76 0.313,0.156 10 false A 0.698,2.365 1.115,2.594 0.417,0.229 10 false AF6 2.542,2.635 2.958,2.865 0.417,0.229 10 false +SL 1.104,2.656 1.521,2.885 0.417,0.229 10 false -SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AF6-1 (+SL) - Body ground Ignition switch ON Below 1 V
AF6-2 (-SL) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C281398C03
0.333,2.25 0.833,2.5 0.5,0.25 1.094,2.896 1.354,2.313 true 1.594,2.854 1.521,2.313 true 1.896,0.615 2.063,0.323 false 1.052,1.083 1.188,0.771 false 0.365,0.615 0.677,0.771 0.313,0.156 10 false *1 2.76,0.76 3.073,0.917 0.313,0.156 10 false *2 0.938,1.115 1.25,1.271 0.313,0.156 10 false *3 2.104,0.219 2.323,0.417 0.219,0.198 10 false *4 0.188,1.719 0.5,1.875 0.313,0.156 10 false *a 0.667,0.615 0.896,0.802 0.229,0.188 10 false F 0.906,0.625 1.135,0.813 0.229,0.188 10 false E 1.354,0.625 1.583,0.813 0.229,0.188 10 false D 1.625,0.615 1.854,0.802 0.229,0.188 10 false C 2.333,0.615 2.563,0.802 0.229,0.188 10 false A 2.094,0.615 2.323,0.802 0.229,0.188 10 false B 0.938,2.885 1.396,3.083 0.458,0.198 10 false -SL 1.479,2.885 1.938,3.083 0.458,0.198 10 false +SL 0.458,2.281 0.917,2.479 0.458,0.198 10 false AF3
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF3-1 (+SL) - AF3-2 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

12.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C292135
0.583,2.333 1.083,2.583 0.5,0.25 1.083,1.094 1.177,0.771 false 1.906,1.083 1.906,0.771 false 1.354,2.719 1.844,2.365 true 2.49,2.708 2.052,2.354 true 0.396,0.615 0.708,0.771 0.313,0.156 10 false *1 2.781,0.76 3.094,0.917 0.313,0.156 10 false *2 1.01,1.104 1.323,1.26 0.313,0.156 10 false *3 1.833,1.104 2.146,1.26 0.313,0.156 10 false *4 0.26,1.781 0.573,1.938 0.313,0.156 10 false *a 0.656,0.615 0.969,0.771 0.313,0.156 10 false F 0.906,0.615 1.219,0.771 0.313,0.156 10 false E 1.354,0.615 1.667,0.771 0.313,0.156 10 false D 2.094,0.604 2.406,0.76 0.313,0.156 10 false B 1.635,0.615 1.948,0.771 0.313,0.156 10 false C 2.344,0.604 2.656,0.76 0.313,0.156 10 false A 0.698,2.365 1.115,2.594 0.417,0.229 10 false AF6 2.542,2.635 2.958,2.865 0.417,0.229 10 false +SL 1.104,2.656 1.521,2.885 0.417,0.229 10 false -SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF6-1 (+SL) - AF6-2 (-SL) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C281397C02
0.625,3.635 1.125,3.885 0.5,0.25 0.969,0.625 1.469,0.875 0.5,0.25 2.052,1.458 2.323,0.938 true 2.74,1.458 2.542,0.938 true 2.344,1.406 2.427,1.198 false 1.302,4.271 1.552,3.698 true 1.729,3.688 1.896,4.25 true 0.854,2.698 1.271,2.281 false 1.885,2.688 1.948,2.281 false 0.406,2.115 0.719,2.271 0.313,0.156 10 false *1 2.802,2.26 3.115,2.417 0.313,0.156 10 false *2 2.26,1.406 2.458,1.594 0.198,0.188 10 false *5 0.979,0.313 1.292,0.469 0.313,0.156 10 false *a 0.354,3.104 0.667,3.26 0.313,0.156 10 false *b 0.708,2.115 0.885,2.302 0.177,0.188 10 false F 0.958,2.125 1.135,2.313 0.177,0.188 10 false E 1.677,2.135 1.854,2.323 0.177,0.188 10 false C 1.417,2.115 1.594,2.302 0.177,0.188 10 false D 2.115,2.125 2.292,2.313 0.177,0.188 10 false B 2.385,2.115 2.563,2.302 0.177,0.188 10 false A 2.781,1.396 3.094,1.552 0.313,0.156 10 false +SL 1.917,4.198 2.229,4.354 0.313,0.156 10 false +SL 0.74,3.677 1.052,3.833 0.313,0.156 10 false AF3 1.083,4.208 1.354,4.385 0.271,0.177 10 false -SL 1.104,0.656 1.417,0.813 0.313,0.156 10 false F21 1.844,1.385 2.115,1.563 0.271,0.177 10 false -SL 0.698,2.677 1.01,2.875 0.313,0.198 10 false *3 1.833,2.708 2.146,2.906 0.313,0.198 10 false *4
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF3-1 (+SL) - AF3-2 (-SL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

14.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C292136
0.979,0.542 1.479,0.792 0.5,0.25 0.75,3.583 1.25,3.833 0.5,0.25 1.167,2.5 1.229,2.219 false 1.938,2.5 1.938,2.219 false 2.417,1.417 2.417,1.135 false 2.031,1.25 2.323,0.844 true 2.729,1.229 2.531,0.833 true 1.417,4 1.875,3.625 true 2.521,3.979 2.073,3.604 true 0.354,2.063 0.667,2.219 0.313,0.156 10 false *1 2.854,2.198 3.167,2.354 0.313,0.156 10 false *2 1.083,2.51 1.396,2.667 0.313,0.156 10 false *3 1.865,2.51 2.177,2.667 0.313,0.156 10 false *4 2.354,1.438 2.667,1.594 0.313,0.156 10 false *5 0.99,0.198 1.302,0.354 0.313,0.156 10 false *a 0.281,3.031 0.594,3.188 0.313,0.156 10 false *b 1.115,0.573 1.438,0.75 0.323,0.177 10 false F21 1.813,1.188 2.135,1.365 0.323,0.177 10 false -SL 2.781,1.156 3.104,1.333 0.323,0.177 10 false +SL 0.719,2.063 1.031,2.219 0.313,0.156 10 false F 0.969,2.063 1.281,2.219 0.313,0.156 10 false E 1.417,2.063 1.729,2.219 0.313,0.156 10 false D 1.677,2.063 1.99,2.219 0.313,0.156 10 false C 2.125,2.063 2.438,2.219 0.313,0.156 10 false B 2.396,2.052 2.708,2.208 0.313,0.156 10 false A 0.885,3.615 1.208,3.792 0.323,0.177 10 false AF6 1.177,3.938 1.5,4.115 0.323,0.177 10 false -SL 2.594,3.917 2.917,4.094 0.323,0.177 10 false +SL
*1 Front Airbag Sensor
*2 Airbag ECU Assembly
*3 Engine Room Main Wire
*4 Instrument Panel Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)


Disconnect the instrument panel wire connector from the engine room main wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AF6-1 (+SL) - AF6-2 (-SL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE