Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER › 2014.03–2016.07
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090624 SHIFT LEVER A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 33550 1.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for LHD)

a.
C286317N01
0.792,2.365 0.917,2.563 0.125,0.198 10 true 1 2.552,1.073 2.688,1.271 0.135,0.198 10 true 2 0.823,1.063 0.958,1.26 0.135,0.198 10 true 3 2.531,2.385 2.667,2.583 0.135,0.198 10 true 4

Temporarily install the transmission floor shift assembly to the body with the 4 bolts.


b.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Engage the 2 clamps to install the wire harness to the transmission floor shift assembly.


d.

Connect the 2 connectors to the transmission floor shift assembly.


Hide 33550 2.INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (for RHD)

a.
C282029N01
0.833,2.313 0.99,2.51 0.156,0.198 10 false 1 2.573,1.031 2.729,1.229 0.156,0.198 10 true 2 0.813,1.021 0.969,1.219 0.156,0.198 10 true 3 2.583,2.323 2.74,2.521 0.156,0.198 10 true 4

Temporarily install the transmission floor shift assembly to the body with the 4 bolts.


b.

Fully tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


c.

Engage the 3 clamps to install the wire harness to the transmission floor shift assembly.


d.

Connect the 2 connectors to the transmission floor shift assembly.


Hide 33820B 3.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.



b.
C286315C02
0.677,2.292 0.875,2.458 false 2.5,2.281 2.698,2.448 false 0.531,2.177 0.844,2.333 0.313,0.156 10 false *a 2.344,2.188 2.656,2.344 0.313,0.156 10 false *1 0.375,2.427 0.531,2.625 0.156,0.198 10 false A 1.313,2.427 1.469,2.625 0.156,0.198 10 false A
*1 Lock
*a Protrusion
V100135

Push in


Install the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.

·

Make sure that the transmission control cable assembly is securely locked.




c.
C286313

Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.




Hide 58910C 6.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 7.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)