In this circuit, the combination meter assembly receives engine speed signals from the ECM using the CAN communication system. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output. | A |
| CAN communication DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| TachoMeter Operation | Tachometer | OFF, 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 | - |
| Tester Display |
|---|
| TachoMeter Operation |
Tachometer indication is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Rpm | Engine speed | Min.: 0 rpm
Max.: 12750 rpm |
650 to 750 rpm (Idling (for Automatic transaxle))
600 to 700 rpm (Idling (for Manual transaxle)) |
- |
| Tester Display |
|---|
| Engine Rpm |
Engine speed displayed on the GTS is almost the same as the tachometer indication.
When the Data List values and tachometer values match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
When the Data List values and tachometer values do not match, an internal malfunction of the combination meter assembly is suspected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if SFI system DTCs are output.
for 1NZ-FE with Automatic Transaxle
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for 1NZ-FE with Manual Transaxle
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
for 2NZ-FE with Automatic Transaxle
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for 2NZ-FE with Manual Transaxle
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
w/ Air Fuel Ratio Sensor
Click here
| Result | Proceed to |
|---|---|
| SFI system DTCs are not output. | A |
| SFI system DTCs are output (for 1NZ-FE with Automatic Transaxle). | B |
| SFI system DTCs are output (for 1NZ-FE with Manual Transaxle). | C |
| SFI system DTCs are output (for 2NZ-FE with Automatic Transaxle). | D |
| SFI system DTCs are output (for 2NZ-FE with Manual Transaxle). | E |
| SFI system DTCs are output. (w/ Air Fuel Ratio Sensor) | F |
A
B
C
D
E
F