Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2014.03–2016.04
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Airbag ECU assembly branch line or connector

·

Power source circuit of airbag ECU assembly

·

Airbag ECU assembly ground circuit

·

Airbag ECU assembly



WIRING DIAGRAM

E285273E01
3.083,1.417 3.5,0.5 3.5,0.5 3.667,0.5 false 0.083,0.083 2.531,0.281 2.448,0.198 10 false V Bus (for LHD): 2.094,0.656 2.854,0.885 0.76,0.229 10 false DLC3 0.677,2.313 1.438,2.542 0.76,0.229 10 false 120 Ω 6.177,2.302 6.938,2.531 0.76,0.229 10 false 120 Ω 3.74,0.406 4.5,0.635 0.76,0.229 10 false F62 3.74,0.573 6.292,0.792 2.552,0.219 10 false No. 1 CAN Junction Connector 0.5,3.094 1.26,3.323 0.76,0.229 10 false ECM 0.51,2.938 1.563,3.135 1.052,0.198 10 false F81*1, F82*2 0.917,4.052 2.292,4.854 1.375,0.802 10 false from Ignition or Starter Switch Assembly*3 or No. 2 Ignition Relay*4 5.813,2.938 6.573,3.167 0.76,0.229 10 false F38 5.813,3.104 7.01,3.542 1.198,0.438 10 false Combination Meter Assembly 2.51,4.198 3.271,4.427 0.76,0.229 10 false A/BAG-IG2 3.271,3.958 3.5,4.167 0.229,0.208 10 false 21 3.531,4.052 3.969,4.25 0.438,0.198 10 false IG2 3.792,3.698 4.229,3.896 0.438,0.198 10 false CANH 4.271,3.698 4.708,3.896 0.438,0.198 10 false CANL 4.677,3.823 4.938,4.042 0.26,0.219 10 false E1 4.667,4.313 4.99,4.51 0.323,0.198 10 false E2 3.531,4.646 3.969,4.844 0.438,0.198 10 false F21 3.531,4.802 4.99,5.021 1.458,0.219 10 false Airbag ECU Assembly 4.031,3.49 4.469,3.688 0.438,0.198 10 false 13 4.448,3.49 4.885,3.688 0.438,0.198 10 false 22 4.948,3.729 5.385,3.927 0.438,0.198 10 false 25 4.958,4.219 5.396,4.417 0.438,0.198 10 false 26 2.406,5.281 3.583,5.531 1.177,0.25 10 false Trouble Area 0.167,5.917 4.458,6.177 4.292,0.26 10 false *1: for Manual Transaxle without Air Fuel Ratio Sensor 0.167,6.333 5.729,6.615 5.563,0.281 10 false *2: for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor 0.167,6.75 2.677,6.979 2.51,0.229 10 false *3: w/o Smart Entry and Start System 0.167,7.167 2.677,7.396 2.51,0.229 10 false *4: w/ Smart Entry and Start System 1.167,7.792 3.083,8.021 1.917,0.229 10 false : CAN Main Bus Line (CANH) 1.167,8.208 3.083,8.438 1.917,0.229 10 false : CAN Main Bus Line (CANL) 4.333,7.792 6.25,8.021 1.917,0.229 10 false : CAN Branch Line (CANH) 4.333,8.208 6.25,8.438 1.917,0.229 10 false : CAN Branch Line (CANL)

E285296E01
3.76,1.406 4.083,0.25 4.083,0.25 4.25,0.25 false 4.844,1.406 5,0.917 5,0.917 5.167,0.917 false 2.094,0.677 2.542,1.01 0.448,0.333 10 false DLC3 4.302,0.156 4.646,0.479 0.344,0.323 10 false F62 4.292,0.313 6.51,0.583 2.219,0.271 10 false No. 1 CAN Junction Connector 5.219,0.823 5.563,1.146 0.344,0.323 10 false F71 5.208,0.979 6.781,1.24 1.573,0.26 10 false No. 2 Junction Connector 6.177,2.333 6.781,2.635 0.604,0.302 10 false 120 Ω 5.833,2.927 6.177,3.25 0.344,0.323 10 false F38 5.823,3.073 7,3.573 1.177,0.5 10 false Combination Meter Assembly 0.479,2.948 1.49,3.24 1.01,0.292 10 false F81*1, F82*2 0.479,3.104 0.948,3.333 0.469,0.229 10 false ECM 0.792,2.323 1.292,2.646 0.5,0.323 10 false 120 Ω 3.313,3.479 3.656,3.802 0.344,0.323 10 false 13 3.719,3.458 4.063,3.781 0.344,0.323 10 false 22 2.542,3.969 2.885,4.292 0.344,0.323 10 false 21 2.813,4.094 3.156,4.417 0.344,0.323 10 false IG2 3.927,3.833 4.271,4.156 0.344,0.323 10 false E1 3.917,4.323 4.26,4.646 0.344,0.323 10 false E2 2.031,5.281 3.219,5.531 1.188,0.25 10 false Trouble Area 4.229,3.771 4.531,4.115 0.302,0.344 10 false 25 4.25,4.26 4.552,4.604 0.302,0.344 10 false 26 2.771,4.646 3.073,4.99 0.302,0.344 10 false F21 2.771,4.792 4.427,5.031 1.656,0.24 10 false Airbag ECU Assembly 1.802,4.198 2.604,4.479 0.802,0.281 10 false A/BAG-IG2 0.292,4.042 1.573,4.813 1.281,0.771 10 false from Ignition or Starter Switch Assembly*3 or No. 2 Ignition Relay*4 1.167,5.833 3.073,6.083 1.906,0.25 10 false : CAN Main Bus Line (CANH) 1.167,6.24 3.073,6.542 1.906,0.302 10 false : CAN Main Bus Line (CANL) 4.323,6.24 6.083,6.479 1.76,0.24 10 false : CAN Branch Line (CANL) 4.323,5.823 6.448,6.052 2.125,0.229 10 false : CAN Branch Line (CANH) 4.75,3.781 6.458,4.021 1.708,0.24 10 false *1: for Manual Transaxle 4.76,4.104 6.521,4.385 1.76,0.281 10 false *2: for Automatic Transaxle 4.76,4.417 7.083,4.698 2.323,0.281 10 false *3: w/o Smart Entry and Start System 4.771,4.76 7.031,5.219 2.26,0.458 10 false *4: w/ Smart Entry and Start System 3.063,3.708 3.646,4.042 0.583,0.333 10 false CANH 3.531,3.708 4.146,4.063 0.615,0.354 10 false CANL 0.125,0.104 1.458,0.427 1.333,0.323 10 false V Bus (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIRBAG ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E186790C03
1.542,0.167 1.958,0.417 0.417,0.25 1.333,1.052 0.604,0.656 true 1.219,1.469 1.531,1.958 true 0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.635,0.188 2.094,0.385 0.458,0.198 10 false F21 0.156,0.583 0.615,0.781 0.458,0.198 10 false CANH 1.594,1.906 2.052,2.104 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Disconnect the airbag ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-13 (CANH) - F21-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIRBAG ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E186790C04
1.563,0.167 1.979,0.417 0.417,0.25 1.021,1.469 0.438,1.792 true 1.677,1.479 1.406,1.875 true 1.833,1.49 2.104,1.844 true 1.646,0.208 2.104,0.406 0.458,0.198 10 false F21 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.292,1.896 1.75,2.094 0.458,0.198 10 false E1 2.063,1.885 2.521,2.083 0.458,0.198 10 false E2 0.177,1.729 0.635,1.927 0.458,0.198 10 false IG2
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-25 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
F21-26 (E2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F21-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)