The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F83-4 (BATT) - B29-1 (E1) | G - W-B | Battery (for measuring battery voltage and for ECM memory) | Always | 11 to 14 V |
| F83-1 (+B) - B29-1 (E1) | R - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| F83-2 (+B2) - B29-1 (E1) | R - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
| B29-7 (+BM) - B29-2 (ME01) | R - W-B | Power source of throttle actuator | Always | 11 to 14 V |
| B29-17 (IGT1) - B29-1 (E1) | B - W-B | No. 1 ignition coil (No. 1 cylinder)
(ignition signal) |
Idling | Pulse generation
(See waveform 1) |
| B29-16 (IGT2) - B29-1 (E1) | Y - W-B | No. 1 ignition coil (No. 2 cylinder)
(ignition signal) |
Idling | Pulse generation
(See waveform 1) |
| B29-15 (IGT3) - B29-1 (E1) | G - W-B | No. 1 ignition coil (No. 3 cylinder)
(ignition signal) |
Idling | Pulse generation
(See waveform 1) |
| B29-14 (IGT4) - B29-1 (E1) | BR - W-B | No. 1 ignition coil (No. 4 cylinder)
(ignition signal) |
Idling | Pulse generation
(See waveform 1) |
| B29-23 (IGF1) - B29-1 (E1) | GR - W-B | No. 1 Ignition coil (ignition confirmation signal) | Ignition switch ON | 4.5 to 5.5 V |
| Idling | Pulse generation
(See waveform 1) |
|||
| B29-27 (NE+) - B29-34 (NE-) | L - B | Crankshaft position sensor signal | Idling with warm engine | Pulse generation
(See waveform 2) |
| B29-26 (VV1+) - B29-34 (NE-) | W - B | Camshaft position sensor signal | Idling with warm engine | Pulse generation
(See waveform 2) |
| B31-7 (#10) - B29-6 (E01) | LG - W-B | Fuel injector assembly injection signal (No. 1 cylinder) | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(See waveform 3) |
|||
| B31-4 (#20) - B29-6 (E01) | P - W-B | Fuel injector assembly injection signal (No. 2 cylinder) | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(See waveform 3) |
|||
| B31-5 (#30) - B29-6 (E01) | Y - W-B | Fuel injector assembly injection signal (No. 3 cylinder) | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(See waveform 3) |
|||
| B31-6 (#40) - B29-6 (E01) | W - W-B | Fuel injector assembly injection signal (No. 4 cylinder) | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(See waveform 3) |
|||
| B31-1 (HA1A) - B31-2 (E03) | R - W-B | Air fuel ratio sensor heater signal | Ignition switch ON | 11 to 14 V |
| Idling | Pulse generation
(See waveform 4) |
|||
| B31-22 (A1A+) - B29-1 (E1) | B - W-B | Air fuel ratio sensor signal | Ignition switch ON | 3.3 V*1 |
| B31-23 (A1A-) - B29-1 (E1) | W - W-B | Air fuel ratio sensor signal | Ignition switch ON | 2.9 V*1 |
| F82-6 (HT1B) - B31-2 (E03) | P - W-B | Heated oxygen sensor heater signal | Ignition switch ON | 11 to 14 V |
| Idling | Below 3.0 V | |||
| F82-27 (OX1B) -F82-26 (EX1B) | W - B | Heated oxygen sensor signal | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor | Pulse generation
(See waveform 5) |
| B31-29 (KNK1) - B31-28 (EKNK) | R - G | Knock sensor signal | Engine speed maintained at 4000 rpm after warming up engine | Pulse generation
(See waveform 6) |
| F82-18 (SPD) - B29-1 (E1) | BR - W-B | Vehicle speed signal (from combination meter assembly) | Driving at 20 km/h (12 mph) | Pulse generation
(See waveform 7) |
| B29-21 (THW) - B29-31 (ETHW) | V - BR | Engine coolant temperature sensor | Idling, Engine coolant temperature 80°C (176°F) | 0.2 to 1.0 V |
| B29-22 (THA) - B29-32 (ETHA) | P - BR | Intake air temperature sensor | Idling, Intake air temperature 20°C (68°F) | 0.5 to 3.4 V |
| B29-30 (VG) - B29-29 (E2G) | V - B | Mass air flow meter | Idling, shift lever in P or N (neutral), A/C off | 0.5 to 3.0 V |
| F82-19 (STA) - B29-1 (E1) | LG - W-B | Starter | Cranking | 5.5 V or higher |
| F82-9 (NSW) - B29-1 (E1) | L - W-B | Park/neutral position switch*2 | Ignition switch ON
(shift lever in P, N) |
Below 1.5 V |
| Ignition switch ON
(shift lever not in P, N) |
11 to 14 V | |||
| Cranking | 6 to 13 V | |||
| Clutch start switch signal*3 | Ignition switch ON
(clutch pedal depressed) |
Below 1.5 V | ||
| Ignition switch ON
(clutch pedal released) |
11 to 14 V | |||
| Cranking | 6 to 13 V | |||
| B29-20 (VTA1) - B29-28 (ETA) | Y - V | Throttle position sensor (for engine control) | Ignition switch ON, Throttle valve fully closed | 0.5 to 1.1 V |
| Ignition switch ON, Throttle valve fully open | 3.2 to 4.8 V | |||
| B29-19 (VTA2) - B29-28 (ETA) | GR - V | Throttle position sensor (for sensor malfunction detection) | Ignition switch ON, Throttle valve fully closed | 2.1 to 3.1 V |
| Ignition switch ON, Throttle valve fully open | 4.6 to 5.0 V | |||
| B29-18 (VCTA) - B29-28 (ETA) | W - V | Power source of throttle position sensor | Ignition switch ON | 4.5 to 5.5 V |
| F83-26 (VCPA) - F83-20 (EPA) | G - BR | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| F83-18 (VPA) - F83-20 (EPA) | P - BR | Accelerator pedal position sensor (for engine control) | Ignition switch ON, Accelerator pedal released | 0.5 to 1.1 V |
| Ignition switch ON, Accelerator pedal fully depressed | 2.6 to 4.5 V | |||
| F83-19 (VPA2) - F83-21 (EPA2) | L - B | Accelerator pedal position sensor (for sensor malfunctioning detection) | Ignition switch ON, Accelerator pedal released | 1.2 to 2.0 V |
| Ignition switch ON, Accelerator pedal fully depressed | 3.4 to 4.75 V | |||
| F83-27 (VCP2) - F83-21 (EPA2) | W - B | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| B29-4 (M+) - B29-2 (ME01) | G - W-B | Throttle actuator signal | Idling with warm engine | Pulse generation
(See waveform 8) |
| B29-3 (M-) - B29-2 (ME01) | BR - W-B | Throttle actuator signal | Idling with warm engine | Pulse generation
(See waveform 9) |
| F83-15 (STP) - B29-1 (E1) | B - W-B | Stop light switch assembly | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V | |||
| F83-16 (ST1-) - B29-1 (E1) | B - W-B | Stop light switch assembly (opposite to STP terminal) | Ignition switch ON, Brake pedal depressed | Below 1.5 V |
| Ignition switch ON, Brake pedal released | 7.5 to 14 V | |||
| B31-19 (PRG) - B29-6 (E01) | L - W-B | Purge VSV signal | Ignition switch ON | 11 to 14 V |
| Idling, under purge control | Pulse generation
(See waveform 10) |
|||
| B29-8 (PBV)*2 - B29-1 (E1) | GR - W-B | Vacuum Switching Valve (for Ejector) | Ignition switch ON | 11 to 14 V |
| F83-10 (FC) - B29-6 (E01) | LG - W-B | Fuel pump control | Ignition switch ON | 11 to 14 V |
| Idling | Below 1.5 V | |||
| F82-1 (TACH) - B29-1 (E1) | R - W-B | Engine speed signal | Idling | Pulse generation
(See waveform 11) |
| F83-23 (TC) - B29-1 (E1) | L - W-B | Terminal TC of DLC 3 | Ignition switch ON | 11 to 14 V |
| B29-13 (OC1+) - B29-12 (OC1-) | GR - BR | Camshaft timing oil control valve signal | Idling | Pulse generation
(See waveform 12) |
| F83-12 (ACMG)*4 - B29-1 (E1) | BE - W-B | Magnet clutch relay | All of the following conditions are met:
·
Engine running ·
Blower switch: 1 ·
A/C switch: Off |
11 to 14 V |
| All of the following conditions are met:
·
Engine running ·
Blower switch: 1 ·
A/C switch: On (magnet clutch on) |
0 to 3.0 V | |||
| F82-24 (AC1)*4 - B29-1 (E1) | L - W-B | Magnet clutch request signal | All of the following conditions are met:
·
Engine running ·
Blower switch: 1 ·
A/C switch: Off |
11 to 14 V |
| All of the following conditions are met:
·
Engine running ·
Blower switch: 1 ·
A/C switch: On (magnet clutch on) |
0 to 3.0 V | |||
| F82-33 (CANH) - B29-1 (E1) | BE - W-B | CAN communication signal | Ignition switch ON | Pulse generation
(See waveform 13) |
| F82-34 (CANL) - B29-1 (E1) | W - W-B | CAN communication signal | Ignition switch ON | Pulse generation
(See waveform 14) |
| F82-14 (ELS1) - B29-1 (E1) | V - W-B | Electric load | Taillight switch on | 7.5 to 14 V |
| Taillight switch off | Below 1.5 V | |||
| F82-13 (ELS2) - B29-1 (E1) | B - W-B*2
SB - W-B*3 |
Electric load | Defogger switch on | 7.5 to 14 V |
| Defogger switch off | Below 1.5 V | |||
| F83-13 (FANL) - B29-1 (E1) | BR - W-B | Cooling fan relay | Ignition switch ON
Cooling fan not operated |
11 to 14 V |
| Idling with A/C on
or High engine coolant temperature Cooling fan operated |
Below 1.5 V | |||
| F83-14 (FANH) - B29-1 (E1) | LG - W-B | Cooling fan relay No. 2 | Idling with high engine coolant temperature
Cooling fan operated at high speed |
Below 1.5 V |
| B31-3 (ALT) - B29-1 (E1) | LG - W-B | Generator assembly | Ignition switch ON | 11 to 14 V |
| F83-9 (IGSW) - B29-1 (E1) | V - W-B | Ignition or starter switch assembly | Ignition switch ON | 11 to 14 V |
| F83-8 (MREL) - B29-1 (E1) | L - W-B | EFI relay | Ignition switch ON | 11 to 14 V |
| F82-20 (EMPS) - B29-1 (E1) | B - W-B | Power steering ECU | Idling (When Steering wheel is turned to some degree) | Below 3.0 V |
| Idling (Steering wheel is neutral) | 11 to 14 V |
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
*2: for Automatic Transaxle
*3: for Manual Transaxle
*4: w/ Air Conditioning System
WAVEFORM 1
| ECM Terminal Name | CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 2
| ECM Terminal Name | CH1: Between VV1+ and NE-
CH2: Between NE+ and NE- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 3
| ECM Terminal Name | Between #10 (to #40) and E01 |
| Tester Range | 20 V/DIV., 20 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 4
| ECM Terminal Name | Between HA1A and E03 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling with warm engine |
The wavelength varies in accordance with the engine operating condition.
WAVEFORM 5
| ECM Terminal Name | Between OX1B and EX1B |
| Tester Range | 0.2 V/DIV., 200 ms./DIV. |
| Condition | Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor |
In the Data List, the items O2S B1S2 show the ECM input values of the heated oxygen sensor.
WAVEFORM 6
| ECM Terminal Name | Between KNK1 and EKNK |
| Tester Range | 1 V/DIV., 1 ms./DIV. |
| Condition | Engine speed maintained at 4000 rpm after warming up engine |
The wavelength becomes shorter as engine speed increases.
The waveforms and amplitudes displayed differ slightly depending on the vehicle.
WAVEFORM 7
| ECM Terminal Name | Between SPD and E1 |
| Tester Range | 2 V/DIV., 20 ms./DIV. |
| Condition | Driving at 20 km/h (12 mph) |
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 8
| ECM Terminal Name | Between M+ and ME01 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 9
| ECM Terminal Name | Between M- and ME01 |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling with warm engine |
The duty ratio varies depending on the throttle actuator operation.
WAVEFORM 10
| ECM Terminal Name | Between PRG and E01 |
| Tester Range | 10 V/DIV., 20 ms./DIV. |
| Condition | Idling, under purge control |
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.
WAVEFORM 11
| ECM Terminal Name | Between TACH and E1 |
| Tester Range | 5 V/DIV., 10 ms./DIV. |
| Condition | Idling |
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 12
| ECM Terminal Name | Between OC1+ and OC1- |
| Tester Range | 5 V/DIV., 1 ms./DIV. |
| Condition | Idling |
WAVEFORM 13
| ECM Terminal Name | Between CANH and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.
WAVEFORM 14
| ECM Terminal Name | Between CANL and E1 |
| Tester Range | 1 V/DIV., 10 μs./DIV. |
| Condition | Ignition switch ON |
The waveform varies depending on the CAN communication signal.