Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0116465 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

1NZ-FE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0500  Vehicle Speed Sensor  


DESCRIPTION

·

w/o ABS


The vehicle speed is detected using the speedometer sensor. The speedometer sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter assembly. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A112641C01
0.396,0.729 1.802,1.031 1.406,0.302 10 false Speedometer Sensor 2.177,0.198 2.719,0.5 0.542,0.302 10 false 4-Pulse 4.594,0.198 5.146,0.51 0.552,0.313 10 false 4-Pulse 5.396,1.74 5.771,2.104 0.375,0.365 10 false ECM 3.156,1.417 4.396,1.792 1.24,0.375 10 false Combination Meter Assembly

·

w/ ABS


The wheel speed sensors monitor the wheel rotation speed and send signals to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



A115899E57
0.771,1.052 1.563,1.427 0.792,0.375 10 false from Speed Sensor 1.833,1.854 3.417,2.417 1.583,0.563 10 false Skid Control ECU 3.5,1.885 5.333,2.052 1.833,0.167 10 false Combination Meter Assembly 3.115,0.604 3.927,0.781 0.813,0.177 10 false 4-Pulse 5.042,0.604 5.854,0.781 0.813,0.177 10 false 4-Pulse 6.073,1.844 6.521,2.01 0.448,0.167 10 false ECM 1.813,2.021 3.5,2.208 1.688,0.188 10 false (Brake Actuator Assembly)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM.
(1 trip detection logic: for Automatic Transaxle)
(2 trip detection logic: for Manual Transaxle)
·

Open or short in speed signal circuit

·

Combination meter assembly

·

Skid control ECU (Brake actuator assembly)*1

·

Speedometer sensor*2

·

ECM


Comes on DTC stored

*1: w/ ABS

*2: w/o ABS


MONITOR DESCRIPTION

for Automatic Transaxle:

The ECM assumes that the vehicle is being driven when the indicated engine speed is more than 2120 rpm and 30 seconds have elapsed since the park/neutral position switch was turned off (typical example value). If there is no speed signal from the combination meter assembly, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


for Manual Transaxle:

The ECM assumes that the vehicle is being driven when fuel cut with the accelerator pedal released continues for 4.53 seconds or more. If there is no speed signal from the combination meter assembly, despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


MONITOR STRATEGY

Required Sensors/Components (Main) Combination meter assembly
Skid control ECU (Brake actuator assembly)*1
Speedometer sensor*2
Required Sensors/Components (Related) Park/neutral position switch*3
Engine coolant temperature sensor
Crankshaft position sensor
Throttle position sensor
Mass air flow meter
Frequency of Operation Continuous

*1: w/ ABS

*2: w/o ABS

*3: for Automatic Transaxle


TYPICAL ENABLING CONDITIONS

for Automatic Transaxle
Ignition Switch ON
Time after ignition switch OFF to ON 3 seconds or more
Battery voltage 11 V or higher
Starter OFF
Time after park/neutral position switch turned off 30 seconds

for Manual Transaxle
Ignition Switch ON
Time after ignition switch OFF to ON 3 seconds or more
Starter OFF
Fuel-Cut ON

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No signal

CONFIRMATION DRIVING PATTERN

A240416C01
5.49,3.552 6.083,2.948 false 0.656,0.875 1.854,1.104 1.198,0.229 10 false 24 km/h (14 mph) 1.417,2.052 1.813,2.219 0.396,0.167 10 false Idling 0.594,2.396 1.771,2.583 1.177,0.188 10 false Ignition Switch ON 2.385,2.271 2.615,2.438 0.229,0.167 10 false [A] 4.708,0.469 4.917,0.635 0.208,0.167 10 false [B] 6.25,3.292 6.448,3.49 0.198,0.198 10 false [D] 6.063,1.125 6.26,1.323 0.198,0.198 10 false [C] 4.01,3.052 5.813,3.198 1.802,0.146 10 false Total of 30 seconds or more 4.323,3.448 5.51,3.594 1.188,0.146 10 false 5 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (14 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Stop the vehicle.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0500.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A309853E06
0.198,0.854 2.042,1.271 1.844,0.417 10 false from Skid Control ECU (Brake Actuator Assembly)*1 2.354,1.865 4.375,2.063 2.021,0.198 10 false Combination Meter Assembly 2.365,1.677 2.646,1.875 0.281,0.198 10 false F38 5.979,1.708 6.26,1.906 0.281,0.198 10 false F82 2.708,0.948 2.99,1.146 0.281,0.198 10 false SI 2.469,0.865 2.75,1.063 0.281,0.198 10 false 34 3.656,0.948 3.938,1.146 0.281,0.198 10 false +S 3.927,0.865 4.208,1.063 0.281,0.198 10 false 35 5.24,0.854 5.521,1.052 0.281,0.198 10 false 18 5.49,0.854 5.833,1.052 0.344,0.198 10 false SPD 5.979,1.885 6.438,2.125 0.458,0.24 10 false ECM 5.313,2.219 6.646,2.542 1.333,0.323 10 false to Other ECUs 6.104,0.531 6.448,0.729 0.344,0.198 10 false 5V 0.198,1.469 2.042,1.885 1.844,0.417 10 false from Speedometer Sensor*2 0.25,2.083 2.271,2.281 2.021,0.198 10 false *1: w/ ABS 0.25,2.417 2.271,2.615 2.021,0.198 10 false *2: w/o ABS

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 234 10

d.

Drive the vehicle.


e.

Read the value displayed on the GTS.


Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

2.CHECK COMBINATION METER SYSTEM (SPEED SIGNAL CIRCUIT)

B

2.CHECK COMBINATION METER SYSTEM (SPEED SIGNAL CIRCUIT)
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

If DTCs (pending DTCs) are not output to the GTS, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END