Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0116465 SFI SYSTEM(w/ Air Fuel Ratio Sensor) J

1NZ-FE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  MIL Circuit  


DESCRIPTION

The ECM is connected to the combination meter assembly via CAN communication.

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit which illuminates the MIL.

The MIL operation can be checked visually: When the ignition switch is turned to ON, the MIL should be illuminated and should turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A301708E09
6.094,0.948 6.708,1.146 0.615,0.198 10 false CANH 6.094,1.292 6.708,1.49 0.615,0.198 10 false CANL 6.365,3.208 6.979,3.406 0.615,0.198 10 false ECM 6.375,3.052 6.729,3.271 0.354,0.219 10 false F82 4.417,0.948 5.031,1.146 0.615,0.198 10 false CANH 4.438,1.302 5.052,1.5 0.615,0.198 10 false CANL 2.979,2.604 5.042,2.99 2.063,0.385 10 false to CAN Communication System 5.875,0.802 6.135,1.021 0.26,0.219 10 false 33 5.885,1.135 6.146,1.354 0.26,0.219 10 false 34 4.875,0.792 5.135,1.01 0.26,0.219 10 false 32 4.875,1.135 5.135,1.354 0.26,0.219 10 false 31 3.458,1.073 4.073,1.271 0.615,0.198 10 false IG+ 3.229,0.969 3.49,1.188 0.26,0.219 10 false 39 2.094,0.958 2.354,1.177 0.26,0.219 10 false 6 0.781,0.969 1.042,1.188 0.26,0.219 10 false 5 2.531,1.229 3.146,1.427 0.615,0.198 10 false METER 0.802,1.594 2.344,2.063 1.542,0.469 10 false Ignition or Starter Switch Assembly 0.813,1.427 1.167,1.646 0.354,0.219 10 false F7 0.938,0.979 1.552,1.177 0.615,0.198 10 false AM2 1.802,0.969 2.417,1.167 0.615,0.198 10 false IG2 0.333,1.719 0.948,1.917 0.615,0.198 10 false AM2 0.375,2.302 0.99,2.5 0.615,0.198 10 false MAIN 0.531,3.604 1.146,3.802 0.615,0.198 10 false Battery 3.219,1.813 3.573,2.031 0.354,0.219 10 false F38 3.208,1.969 5.271,2.354 2.063,0.385 10 false Combination Meter Assembly 2.198,3.458 5.865,3.656 3.667,0.198 10 false : CAN Communication Line 0.354,2.948 0.969,3.146 0.615,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Turn the ignition switch to ON.


b.

Check the illumination condition of the MIL.


Result:
Condition Proceed to
MIL remains illuminated A
MIL remains off (Does not illuminate at all) B
MIL illuminates for several seconds, but turns off after engine is started C



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

4.CHECK THAT ENGINE STARTS

C

2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
No DTC detected A
Any DTCs detected B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

3.CHECK CAN COMMUNICATION SYSTEM

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

B

4.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.


HINT:

*: The GTS cannot communicate with the ECM.


Result:
Result Proceed to
Engine starts A
Engine does not start* B



A

B