17410
1.INSTALL FRONT EXHAUST PIPE ASSEMBLY
Using a vernier caliper, measure the free length of the compression spring.
| Standard Length | Minimum Length |
|---|---|
| 42 mm (1.65 in.) | 40.5 mm (1.59 in.) |
If the length is not as specified, replace the compression spring.
| *1 | Exhaust Manifold |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
| *b | Plastic Hammer |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.
Install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gasket.
Do not damage the exhaust pipe gasket by dropping it, etc.
Do not damage the outer surface of the exhaust pipe gasket.
Do not push in the exhaust pipe gasket with the front exhaust pipe assembly when connecting it.
Connect the 3 exhaust pipe supports to install the front exhaust pipe assembly to the vehicle.
| *1 | Exhaust Manifold |
| *2 | Front Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 8.5 mm (0.335 in.) |
Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts.
43 N*m (440 kgf*cm, 32 ft.*lbf)
After the installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
17430
2.INSTALL TAIL EXHAUST PIPE ASSEMBLY (for Sedan)
Using a vernier caliper, measure the free length of the compression spring.
| Standard Length | Minimum Length |
|---|---|
| 40 mm (1.57 in.) | 38.5 mm (1.52 in.) |
If the length is not as specified, replace the compression spring.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
| *b | Plastic Hammer |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
Install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gasket.
Do not damage the exhaust pipe gasket by dropping it, etc.
Do not damage the outer surface of the exhaust pipe gasket.
Do not push in the exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.
Connect the 3 exhaust pipe supports to install the tail exhaust pipe assembly to the vehicle.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Tail Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 6.5 mm (0.256 in.) |
Install the tail exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
43 N*m (440 kgf*cm, 32 ft.*lbf)
After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
17430
3.INSTALL TAIL EXHAUST PIPE ASSEMBLY (for Hatchback)
Using a vernier caliper, measure the free length of the compression spring.
| Standard Length | Minimum Length |
|---|---|
| 40 mm (1.57 in.) | 38.5 mm (1.52 in.) |
If the length is not as specified, replace the compression spring.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
| *b | Plastic Hammer |
Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.
Install the exhaust pipe gasket in the correct direction.
Do not reuse the exhaust pipe gasket.
Do not damage the exhaust pipe gasket by dropping it, etc.
Do not damage the outer surface of the exhaust pipe gasket.
Do not push in the exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.
Connect the 2 exhaust pipe supports to install the tail exhaust pipe assembly to the vehicle.
| *1 | Front Exhaust Pipe Assembly |
| *2 | Tail Exhaust Pipe Assembly |
| *3 | Exhaust Pipe Gasket |
| *a | Space between flanges: 6.5 mm (0.256 in.) |
Install the tail exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.
43 N*m (440 kgf*cm, 32 ft.*lbf)
After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
57533B
4.INSTALL FRONT FLOOR CENTER BRACE
89465A
5.INSTALL HEATED OXYGEN SENSOR (for Sensor 2)
6.INSPECT FOR EXHAUST GAS LEAK