DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start, Power Source Control or Combination Meter / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Trigger Switch | Driver door trigger switch | ON or OFF | ON: Driver door trigger switch pressed
OFF: Driver door trigger switch not pressed |
·
Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate. |
| Tr/B-Door Lock SW | Back door opener switch assembly (lock switch)*2 | ON or OFF | ON: Back door opener switch assembly (lock switch) pushed
OFF: Back door opener switch assembly (lock switch) not pushed |
·
Displays whether the back door opener switch assembly (unlock switch) is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate. |
| Tr/B-Door Unlock SW | Luggage door opening switch assembly*1 or back door opening switch assembly (unlock switch)*2 | ON or OFF | ON: Luggage door opening switch assembly*1 or back door opener switch assembly (unlock switch)*2 pushed
OFF: Luggage door opening switch assembly*1 or back door opener switch assembly (unlock switch)*2 not pushed |
·
Displays whether the luggage door opening switch assembly*1 or back door opener switch assembly (unlock switch) *2 is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the luggage compartment door*1 or back door*2 open function does not operate. |
| Unmatched Vehicle-ID | Key No. (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
The vehicle ID registered in the vehicle and the vehicle ID registered in the electrical key transmitter sub-assembly are different (if a key from another vehicle is brought into the vehicle exterior detection area while the doors are locked, "Yes" is displayed for "Unmatched Vehicle-ID" in the Data List).
Other potential causes: ·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
A communication error due to electric wave interference. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| No Response | Communication response | Yes or No | Yes: Communication malfunction
No: Communication normal |
The vehicle IDs registered in the vehicle and electrical key transmitter sub-assembly match, but there is no response from the electrical key transmitter sub-assembly. (If the electrical key transmitter sub-assembly is not in the detection area or the transmitter battery is depleted resulting in a matching code not being detected when a lock switch or the engine switch is pressed, etc., "Yes" is displayed for "No Response" in the Data List. If there is wave interference in the LF band that the vehicle uses for transmission or the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "No Response" in the Data List.)
Other potential causes: ·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| Unmatch Code or Form | Code format (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
There is an error in the data sent from the electrical key transmitter sub-assembly (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
Other potential causes: ·
An electrical key transmitter sub-assembly from a different manufacturer is being used. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| Key Low Battery | Transmitter battery depleted | Yes or No | Yes: Transmitter battery depleted
No: Transmitter battery not depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.1 V or less. This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| # Codes | Number of trouble codes | Min: 0, Max: 255 | Number of stored DTCs displayed | - |
| ID Code Difference(Resp) | ID code (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
Other potential causes: ·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| C Code Difference | Challenge code (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
The electrical key transmitter sub-assembly sends a response code in response to the challenge code from the vehicle, but the response code is incorrect (if there is wave interference in the RF band that the electrical key transmitter sub-assembly uses for transmission, "Yes" may be displayed for "Unmatch Code or Form", "No Response", "ID Code Difference(Resp)" and "C Code Difference" in the Data List).
Other potential causes: ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| ID Code Difference | Wireless ID code (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
The ID code registered in the vehicle and the ID code registered in the electrical key transmitter sub-assembly are different. (If a wireless ID other than those for any of the registered electrical key transmitter sub-assemblies is detected, "Yes" is displayed for "ID Code Difference" in the Data List. If a wireless signal from the electrical key transmitter sub-assembly of another vehicle is detected, "Yes" is displayed for "ID Code Difference(Resp)" in the Data List.)
Other potential causes: ·
An electrical key transmitter sub-assembly from a different vehicle is being used. ·
A communication error due to external noise (RF). ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| Immobilizer when IG=ON | Immobiliser system status when power source mode on (IG) | SET or UNSET | SET: Immobiliser system set (engine switch off)
UNSET: Immobiliser system unset (engine switch on (ACC) or on (IG)) |
- |
| Immobiliser | Immobiliser system status determined by certification ECU | Set or Unset | Set: Immobiliser set (engine start prohibited) (engine switch off)
Unset: Immobiliser unset (engine start permitted) (engine switch on (ACC) or on (IG)) |
When the immobiliser system does not change to the unset state, this item can be used to determine if the cause is the certification ECU. |
| Different Rolling Code | Rolling code (incorrect or correct) | Yes or No | Yes: Communication malfunction
No: Communication normal |
The rolling code registered in the vehicle and the rolling code registered in the electrical key transmitter sub-assembly are different
Other potential causes: ·
An electrical key transmitter sub-assembly switch is pressed 100 times or more in a location where the electric waves cannot reach the vehicle. ·
A communication error due to external noise (RF). ·
The electrical key transmitter sub-assembly or certification ECU (smart key ECU assembly) is malfunctioning. |
| Auto Entry Cancel SW | Entry cancel function setting | ON or OFF | Mode status displayed
ON: Smart entry and start system canceled OFF: Smart entry and start system not canceled |
The default setting for the entry cancel function is OFF. If the customer requests that the smart entry and start system functions (locking and unlocking the doors while carrying the electrical key transmitter sub-assembly, etc.) be canceled, the setting can be changed through the customize function. |
| S Code Check | S code verification result | OK or NG | OK: S code verification result normal
NG: S code verification result abnormal |
·
Always "OK" is displayed. ·
No diagnostic function |
| L Code Check | L code verification result | OK or NG | OK: L code verification result normal
NG: L code verification result abnormal |
Problems may be caused by the following:
·
Registration has not been performed for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly). ·
Malfunctions in the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly). |
| Unlock Request Receive | Status of steering unlock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on (ACC) or on (IG), or of engine start operation performed)
NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on (ACC) or on (IG), and engine start operation not performed) |
- |
| Lock Request Receive | Status of steering lock command from certification ECU (smart key ECU assembly) | OK or NG | OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P*3 and engine switch off)
NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P*3 and engine switch off) |
- |
| S Code Check(Past) | S code verification result (past) | OK or NG (Past) | OK: Verification result normal
NG (Past): Verification result abnormal (past) |
·
Always "OK" is displayed. ·
No diagnostic function. |
| L Code Check(Past) | L code verification result (past) | OK or NG (Past) | OK: Verification confirmed (past)
NG (Past): Verification not confirmed (past) |
- |
| Steering Lock | State of whether steering lock ECU (steering lock actuator assembly) has determined steering is locked | Set or Unset | Set: Steering locked
Unset: Steering unlocked |
- |
| Steering Unlock | State of whether steering lock ECU (steering lock actuator assembly) determined steering is unlocked | Set or Unset | Set: Steering unlocked
Unset: Steering locked |
- |
| Trunk Open Mode | Luggage compartment door open mode*1 | ON or OFF | Customization status displayed | - |
| B-Dr Opening Operation | Back door opening operation*2 | Long, Twice or OFF | Customization status displayed | - |
*1: for Sedan
*2: for Hatchback
*3: Automatic Transaxle
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift P Signal | Shift position P*1 | ON or OFF | ON: Shift lever in P
OFF: Shift lever not in P |
·
Use this item to determine if the shift position switch is malfunctioning. ·
The engine cannot be started when this item is OFF. |
| Steering Unlock Switch | State of steering unlock sensor signal output from steering lock actuator assembly | ON or OFF | ON: Steering unlocked
OFF: Steering locked |
·
When the shift lever is in P*1 and the engine switch is off, if any door is opened then closed, the steering is locked. ·
When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks. ·
The engine cannot be started when the steering unlock signal is off. |
| Stop Light Switch1 | State of brake pedal*1 | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The engine cannot be started when this item is OFF. ·
When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
| Start Switch1 | Engine switch 1 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
| Vehicle Speed Signal | Vehicle being driven or stopped | Stop or Run | Stop: Vehicle stopped
Run: Vehicle being driven at 5 km/h (3 mph) or more |
- |
| Power Supply Condition | Power supply state | IG2 ON, ST ON, ALL OFF, IG1 ON or ACC ON | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG1 ON: Engine switch on (IG) (IG1 relay on) IG2 ON: Engine switch on (IG) (IG2 relay on) ST ON: Sending engine start request signal |
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
*1: Automatic Transaxle
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed | Min.: 0, Max.: 255 | Almost the same as actual vehicle speed | - |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Overhead Tuner Power Supply ON | Door control receiver | OFF/ON | - |
| Power for P-Seat Sens | Front door outside handle (for front passenger door) | OFF/ON | - |
| Power/Engine SW Light | Engine switch light | OFF/ON | ·
When performing this Active Test, make sure the following condition is met: ·
The engine switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the engine switch is on (ACC) or on (IG), or the engine is running. |
| Multi Channel SW | Door control receiver | CH1/CH2 | - |
| Wireless Buzzer Operation | Wireless door lock buzzer | OFF/ON | - |