Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) › 2014.03–2017.10
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0091389 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the body computer through the certification ECU (smart key ECU assembly). (ex. if a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the body computer).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short in RDAS to ground between the certification ECU (smart key ECU assembly) and door control receiver.

·

Short in RDAS to ground when RCO (5 V) output from the ECU is off.


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

E281444E01
0.865,2.146 2.25,2.344 1.385,0.198 10 false Door Control Receiver 4.969,2.021 6.49,2.427 1.521,0.406 10 false Certification ECU (Smart Key ECU Assembly) 0.865,1.99 1.188,2.188 0.323,0.198 10 false F46 4.865,1.51 5.188,1.708 0.323,0.198 10 false F43 4.865,1.021 5.188,1.219 0.323,0.198 10 false F44 4.875,0.521 5.198,0.719 0.323,0.198 10 false F44 4.969,0.333 5.167,0.552 0.198,0.219 10 false 3 4.927,0.802 5.125,1.021 0.198,0.219 10 false 22 4.917,1.323 5.115,1.542 0.198,0.219 10 false 10 5.25,0.5 5.719,0.708 0.469,0.208 10 false RCO 5.25,1 5.719,1.208 0.469,0.208 10 false RDAS 5.25,1.5 5.719,1.708 0.469,0.208 10 false E 2.167,0.417 2.365,0.635 0.198,0.219 10 false 4 2.167,0.917 2.365,1.135 0.198,0.219 10 false 5 2.177,1.406 2.375,1.625 0.198,0.219 10 false 1 1.896,0.51 2.115,0.729 0.219,0.219 10 false +5 1.708,1.01 2.125,1.219 0.417,0.208 10 false DATA 1.771,1.51 2.115,1.719 0.344,0.208 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.

·

This DTC is not detected within 10 seconds after the engine switch is turned to off from ON.

·

When replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B272823C09
1.5,0.25 1.917,0.5 0.417,0.25 1.677,1.74 1.833,1.302 true 0.906,1.75 1.323,1.302 true 2.115,1.302 2.396,1.74 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.604,0.302 1.917,0.5 0.313,0.198 10 false F46 0.708,1.771 1.094,1.979 0.385,0.208 10 false GND 1.563,1.781 1.948,1.99 0.385,0.208 10 false +5 2.406,1.781 2.854,2 0.448,0.219 10 false DATA
*a Front view of wire harness connector
(to Door control receiver)


Disconnect the door control receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F46-4 (+5) - F46-1 (GND) Always 4.5 to 5.5 V pulse generation at regular intervals
F46-5 (DATA) - F46-1 (GND) Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
F46-1 (GND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for Sedan) A
OK (for Hatchback) B
NG C



A

B

C

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F46 door control receiver connector.


b.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F46-5 (DATA) - F44-22 (RDAS) Always Below 1 Ω
F46-4 (+5) - F44-3 (RCO) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F46-5 (DATA) or F44-22 (RDAS) - Body ground Always 10 kΩ or higher
F46-4 (+5) or F44-3 (RCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR