Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2014.03–2016.04
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090852 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B343158E07
1.667,0.5 2.125,0.698 0.458,0.198 10 false F82 1.656,1.25 2.115,1.448 0.458,0.198 10 false F82 2.063,0.5 2.521,0.698 0.458,0.198 10 false F81 2.052,1.25 2.51,1.448 0.458,0.198 10 false F81 1.688,0.292 1.969,0.531 0.281,0.24 10 false 16 2.083,0.292 2.365,0.531 0.281,0.24 10 false 19 1.688,1.042 1.969,1.281 0.281,0.24 10 false 15 2.073,1.042 2.354,1.281 0.281,0.24 10 false 18 1.26,0.51 1.719,0.708 0.458,0.198 10 false IMI 1.208,1.271 1.667,1.469 0.458,0.198 10 false IMO 5.781,0.51 6.24,0.708 0.458,0.198 10 false EFIO 5.552,0.385 5.833,0.625 0.281,0.24 10 false 4 5.552,1.115 5.833,1.354 0.281,0.24 10 false 5 5.781,1.25 6.24,1.448 0.458,0.198 10 false EFII 5.688,1.979 6.146,2.177 0.458,0.198 10 false F51 5.688,2.135 6.771,2.521 1.083,0.385 10 false Transponder Key ECU Assembly 0.948,1.99 1.406,2.188 0.458,0.198 10 false ECM 1.958,1.76 5.083,2.135 3.125,0.375 10 false *1: for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor 1.708,0.719 1.99,0.958 0.281,0.24 10 false *1 1.698,1.479 1.979,1.719 0.281,0.24 10 false *1 2.094,0.729 2.375,0.969 0.281,0.24 10 false *2 2.094,1.49 2.375,1.729 0.281,0.24 10 false *2 1.958,2.417 5.438,2.719 3.479,0.302 10 false *2: for Manual Transaxle without Air Fuel Ratio Sensor

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine and ECT > Clear DTCs
50002 234

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine and ECT > Trouble Codes
50001 234
OK:

DTC is not output



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Perform the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
OK:

OFF is displayed after the engine is started



Result:
Result Proceed to
OK (for 1NZ-FE with Automatic Transaxle) A
OK (for 1NZ-FE with Manual Transaxle) B
OK (for 1NZ-FE with Air Fuel Ratio Sensor) C
OK (for 2NZ-FE with Automatic Transaxle) D
OK (for 2NZ-FE with Manual Transaxle) E
NG F



A

B

C

D

E

F

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Proceed to
OK
NG



OK

NG

5.CHECK ECM (TERMINAL IMI)
5.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B343144C04
4.177,0.188 4.75,0.5 0.573,0.313 2,2.021 2.573,2.333 0.573,0.313 3.26,3.583 3.833,3.896 0.573,0.313 1.281,3.208 2,3 true 4.219,1.844 3.927,1.146 true 3.563,4.875 3.542,4.375 true 0.688,0.417 1,0.573 0.313,0.156 10 false *A 1.104,2.333 1.417,2.49 0.313,0.156 10 false *B 0.271,0.167 0.583,0.323 0.313,0.156 10 false *a 2.042,3.76 2.354,3.917 0.313,0.156 10 false *b 2.313,6.854 2.625,7.01 0.313,0.156 10 false *c 4.167,1.875 4.479,2.042 0.313,0.167 10 false IMI 2.167,2.083 2.479,2.25 0.313,0.167 10 false F81 3.427,3.667 3.74,3.833 0.313,0.167 10 false F51 4.333,0.25 4.646,0.417 0.313,0.167 10 false F82 1.052,3.125 1.365,3.292 0.313,0.167 10 false IMI 3.458,4.906 3.771,5.073 0.313,0.167 10 false EFIO 0.979,6.76 1.292,6.927 0.313,0.167 10 false GND
*A for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor *B for Manual Transaxle without Air Fuel Ratio Sensor
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform A - -


Item Content
Terminal No. (Symbol) F82-16 (IMI) - F51-4 (EFIO)*1
F81-19 (IMI) - F51-4 (EFIO)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor

*2: for Manual Transaxle without Air Fuel Ratio Sensor


OK:

Waveform is output normally (refer to illustration)


Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape B




A

6.CHECK ECM (TERMINAL IMO)

B

14.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B343145C03
4.167,0.167 4.667,0.5 0.5,0.333 2,2 2.5,2.333 0.5,0.333 3.292,3.583 3.792,3.917 0.5,0.333 4.417,1.833 4.042,1.146 true 1.375,3.146 2.115,3.021 true 3.771,4.99 3.438,4.375 true 0.688,0.5 1,0.656 0.313,0.156 10 false *A 1.188,2.333 1.5,2.49 0.313,0.156 10 false *B 0.333,0.167 0.646,0.323 0.313,0.156 10 false *a 2,3.813 2.313,3.969 0.313,0.156 10 false *b 2.875,5.74 3.146,5.906 0.271,0.167 10 false *c 2.542,6.896 2.854,7.052 0.313,0.156 10 false *d 2.958,6.833 3.271,6.99 0.313,0.156 10 false *e 4.292,0.24 4.604,0.396 0.313,0.156 10 false F82 2.125,2.073 2.438,2.229 0.313,0.156 10 false F81 3.417,3.656 3.729,3.813 0.313,0.156 10 false F51 3.604,5.042 4.083,5.208 0.479,0.167 10 false EFII 0.938,6.75 1.417,6.917 0.479,0.167 10 false GND 1.073,3.073 1.552,3.24 0.479,0.167 10 false IMO 4.313,1.885 4.792,2.052 0.479,0.167 10 false IMO
*A for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor *B for Manual Transaxle without Air Fuel Ratio Sensor
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform B *d Approximately 160 ms
*e Approximately 510 ms - -


Item Content
Terminal No. (Symbol) F82-15 (IMO) - F51-5 (EFII)*1
F81-18 (IMO) - F51-5 (EFII)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor

*2: for Manual Transaxle without Air Fuel Ratio Sensor


OK:

Waveform is output normally (refer to illustration)


Result:
Result Proceed to
Normal waveform A
Waveform B not output, or has abnormal wavelength or shape (for 1NZ-FE) B
Waveform B not output, or has abnormal wavelength or shape (for 2NZ-FE) C




A

7.CHECK ECM (TERMINAL IMI)

B

C

7.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B343146C03
4.25,0.188 4.74,0.5 0.49,0.313 2.01,2.021 2.5,2.333 0.49,0.313 3.292,3.604 3.781,3.917 0.49,0.313 2.917,6.917 3.031,6.865 3.031,6.865 3.167,6.802 true 1.375,3.292 1.979,2.99 true 3.5,4.833 3.573,4.375 true 4.146,1.854 3.938,1.135 true 0.729,0.479 1.042,0.635 0.313,0.156 10 false *A 1.188,2.354 1.5,2.51 0.313,0.156 10 false *B 0.26,0.156 0.573,0.313 0.313,0.156 10 false *a 2.042,3.74 2.354,3.896 0.313,0.156 10 false *b 3.198,5.656 3.51,5.813 0.313,0.156 10 false *c 2.729,6.823 2.927,7.01 0.198,0.188 10 false *d 3.292,6.792 3.583,7 0.292,0.208 10 false *e 4.354,0.26 4.667,0.417 0.313,0.156 10 false F82 2.104,2.094 2.417,2.25 0.313,0.156 10 false F81 3.417,3.677 3.729,3.833 0.313,0.156 10 false F51 0.854,6.708 1.167,6.865 0.313,0.156 10 false GND 3.385,4.875 3.865,5.042 0.479,0.167 10 false EFIO 1.135,3.208 1.615,3.375 0.479,0.167 10 false IMI 4.083,1.885 4.563,2.052 0.479,0.167 10 false IMI
*A for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor *B for Manual Transaxle without Air Fuel Ratio Sensor
*a Component with harness connected
(ECM)
*b Component with harness connected
(Transponder Key ECU Assembly)
*c Waveform C *d Approximately 160 ms
*e Approximately 270 ms - -


Item Content
Terminal No. (Symbol) F82-16 (IMI) - F51-4 (EFIO)*1
F81-19 (IMI) - F51-4 (EFIO)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

*1: for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor

*2: for Manual Transaxle without Air Fuel Ratio Sensor


OK:

Waveform is output normally (refer to illustration)


Result:
Result Proceed to
Normal waveform A
Waveform C not output, or has abnormal wavelength or shape B




A

8.REGISTER ECU COMMUNICATION ID

B

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
8.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Proceed to
OK
NG



OK

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

NG

10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
10.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.REGISTER KEY
11.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

12.REGISTER ECU COMMUNICATION ID
12.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

13.CHECK WHETHER ENGINE STARTS
13.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Result Proceed to
OK A
NG (for 1NZ-FE with Automatic Transaxle) B
NG (for 1NZ-FE with Manual Transaxle) C
NG (for 1NZ-FE with Air Fuel Ratio Sensor) D
NG (for 2NZ-FE with Automatic Transaxle) E
NG (for 2NZ-FE with Manual Transaxle) F



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C

D

E

F

14.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the F51 transponder key ECU assembly connector.


b.

Disconnect the F82*1 or F81*2 ECM connector.

*1: for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor

*2: for Manual Transaxle without Air Fuel Ratio Sensor



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F51-4 (EFIO) - F82-16 (IMI)*1 Always Below 1 Ω
F51-4 (EFIO) - F81-19 (IMI)*2 Always Below 1 Ω
F51-4 (EFIO) - Body ground Always 10 kΩ or higher
F82-16 (IMI) - Body ground*1 Always 10 kΩ or higher
F81-19 (IMI) - Body ground*2 Always 10 kΩ or higher


*1: for Automatic Transaxle or for Manual Transaxle with Air Fuel Ratio Sensor

*2: for Manual Transaxle without Air Fuel Ratio Sensor



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR