Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › 2014.03–2017.10
RM30M0E _59 Vehicle Exterior _017125 WIPER / WASHER _0090078 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

a.

Check the resistance.

i.
B347427C02
1.167,0.417 1.5,0.667 0.333,0.25 2.167,0.417 2.5,0.667 0.333,0.25 0.979,1.896 0.333,1.167 true 1.208,1.885 0.656,1.063 true 1.469,1.885 1.063,1.052 true 1.708,1.875 2.125,1.063 true 2.135,1.875 2.604,1.073 true 2.344,1.885 2.99,1.156 true 1.677,2.271 1.458,2.865 true 2.146,2.271 2.385,2.844 true 0,0 0.313,0.156 0.313,0.156 10 false *a 0.469,0.958 0.781,1.115 0.313,0.156 10 false +1 2.625,0.948 2.948,1.104 0.323,0.156 10 false WF 2.958,0.948 3.281,1.135 0.323,0.188 10 true EW 0.844,0.948 1.156,1.104 0.313,0.156 10 false +B 0.167,0.958 0.479,1.115 0.313,0.156 10 true +2 2.135,0.948 2.448,1.104 0.313,0.156 10 false +S 1.271,0.438 1.583,0.635 0.313,0.198 12 false A 2.271,0.448 2.583,0.646 0.313,0.198 12 false B 1.323,2.906 1.667,3.094 0.344,0.188 10 false WR 2.323,2.896 2.646,3.083 0.323,0.188 10 true +1R
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
A-1 (+S) - A-3 (+1) OFF Below 1 Ω
INT
A-2 (+B) - A-3 (+1) MIST
LO
A-2 (+B) - A-4 (+2) HI

Front Washer Switch
Tester Connection Switch Condition Specified Condition
B-2 (EW) - B-3 (WF) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Wiper Switch
Tester Connection Switch Condition Specified Condition
A-5 (WR) - B-2 (EW) OFF 10 kΩ or higher
B-7 (+1R) - B-2 (EW)
B-7 (+1R) - B-2 (EW) ON Below 1 Ω

Rear Washer Switch
Tester Connection Switch Condition Specified Condition
A-5 (WR) - B-2 (EW) OFF 10 kΩ or higher
B-7 (+1R) - B-2 (EW)
A-5 (WR) - B-2 (EW) WASH Below 1 Ω
A-5 (WR) - B-2 (EW) ON + WASH Below 1 Ω
B-7 (+1R) - B-2 (EW)


If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the intermittent operation. (w/o Intermittent Timing Adjustment)

i.

Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector.


ii.

Connect the positive (+) battery lead to terminal 2 (+B) of the A connector and the negative (-) battery lead to terminals 2 (EW) of the B connector and 1 (+S) of the A connector.


iii.

Turn the wiper switch to the INT position.


iv.

Connect the positive (+) battery lead to terminal 1 (+S) of the A connector for 5 seconds.


v.

Connect the negative (-) battery lead to terminal 1 (+S) of the A connector. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) of the A connector and 2 (EW) of the B connector.

OK:

Refer to the illustration below.


E129662E15
0.156,0.5 1.802,0.896 1.646,0.396 10 false Voltage between terminals A-3 (+1) and B-2 (EW) 3.125,0.01 5.604,0.365 2.479,0.354 10 false Connect the negative (-) battery terminal cable to terminal A-1 (+S) 3.208,0.677 3.854,0.854 0.646,0.177 10 false 10 to 14 V 3.896,1.156 4.188,1.333 0.292,0.177 10 false 0 V 3.906,1.458 5.063,1.635 1.156,0.177 10 false 2.3 to 4.3 seconds

If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the intermittent operation. (w/ Intermittent Timing Adjustment)

i.

Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the A connector and negative (-) voltmeter terminal to terminal 2 (EW) of the B connector.


ii.

Connect the positive (+) battery lead to terminal 2 (+B) of the A connector and negative (-) battery lead to terminals 2 (EW) of the B connector and 1 (+S) of the A connector.


iii.

Turn the front wiper switch to the INT position.


iv.

Connect the positive (+) battery lead to terminal 1 (+S) of the A connector for 5 seconds.


v.

Connect the negative (-) battery lead to terminal 1 (+S) of the A connector. Operate the intermittent wiper relay and check the voltage between terminals 3 (+1) of the A connector and 2 (EW) of the B connector.

OK:

Refer to the illustration below.


E258319E04
2.438,0.313 4.802,0.708 2.365,0.396 10 false FAST: Connect the negative (-) battery terminal cable to terminal A-1 (+S) 4.688,0.938 7.125,1.521 2.438,0.583 10 false SLOW: Connect the negative (-) battery terminal cable to terminal A-1 (+S) 0.073,2.167 1.771,2.719 1.698,0.552 10 false Voltage between terminals A-3 (+1) and B-2 (EW) 1.667,1.781 2.615,2.073 0.948,0.292 10 false 11 to 14 V 2.177,2.26 2.75,2.635 0.573,0.375 10 false 0 V 2.344,2.76 3.875,3.063 1.531,0.302 10 false 0.6 to 2.6 seconds 4.583,2.76 6.083,3.083 1.5,0.323 10 false 5.7 to 15.7 seconds

If the result is not as specified, replace the windshield wiper switch assembly.



d.

Check the operation (front washer).

i.

Turn the front wiper switch off.


ii.

Connect the positive (+) battery lead to terminal 2 (+B) of the A connector and negative (-) battery lead to terminal 1 (+S) of the A connector and 2 (EW) of the B connector.


iii.

Connect the positive (+) voltmeter terminal to terminal 3 (+1) of the A connector and negative (-) voltmeter terminal to terminal 2 (EW) of the B connector. Turn the washer switch on and off, and check the voltage between terminals 3 (+1) of the A connector and 2 (EW) of the B connector.

OK:

Refer to the illustration below.


E273971E02
4,1.302 4,1.177 false 4.865,1.302 4.667,1.167 false 3.583,0.385 3.885,0.615 0.302,0.229 10 false ON 3.552,0.552 3.896,0.781 0.344,0.229 10 false OFF 3.25,0.792 3.948,0.969 0.698,0.177 10 false 11 to 14 V 3.573,1.042 3.854,1.208 0.281,0.167 10 false 0 V 4.229,0.083 5.25,0.25 1.021,0.167 10 false Washer Switch 2.542,1.313 4.281,1.51 1.74,0.198 10 false Approximately 0.5 seconds 4.688,1.302 6.427,1.5 1.74,0.198 10 false Approximately 2.2 seconds 0.188,0.333 1.833,0.688 1.646,0.354 10 false Voltage between terminals A-3 (+1) and B-2 (EW)

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

a.

Check the resistance.

i.
B345174C04
0.792,0.25 1.208,0.5 0.417,0.25 1.875,0.25 2.292,0.5 0.417,0.25 2.438,1.875 3,0.917 true 2.198,1.875 2.583,0.917 true 1.948,1.875 1.656,0.917 true 1.708,1.885 1.354,0.885 true 1.313,1.875 0.833,0.875 true 1.083,1.875 0.417,0.854 true 1.51,2.875 1.708,2.271 true 1.104,2.875 1.302,2.271 true 0.052,0.052 0.365,0.25 0.313,0.198 10 true *a 0.177,0.76 0.448,0.99 0.271,0.229 10 false EW 0.594,0.771 0.865,1 0.271,0.229 10 false WF 1.479,0.771 1.75,1 0.271,0.229 10 false +B 1.146,0.771 1.417,1 0.271,0.229 10 false +S 3.031,0.781 3.302,1.01 0.271,0.229 10 false +2 2.594,0.781 2.865,1.01 0.271,0.229 10 false +1 0.958,0.281 1.229,0.51 0.271,0.229 10 false B 2.042,0.281 2.313,0.51 0.271,0.229 10 false A 0.917,2.938 1.188,3.167 0.271,0.229 10 false +1R 1.375,2.927 1.646,3.156 0.271,0.229 10 false WR
*a Component without harness connected
(Windshield Wiper Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
A-4 (+S) - A-2 (+1) OFF Below 1 Ω
INT
A-3 (+B) - A-2 (+1) MIST
LO
A-3 (+B) - A-1 (+2) HI

Front Washer Switch
Tester Connection Switch Condition Specified Condition
B-2 (EW) - B-1 (WF) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Wiper Switch
Tester Connection Switch Condition Specified Condition
A-10 (WR) - B-2 (EW) OFF 10 kΩ or higher
B-4 (+1R) - B-2 (EW)
B-4 (+1R) - B-2 (EW) ON Below 1 Ω

Rear Washer Switch
Tester Connection Switch Condition Specified Condition
A-10 (WR) - B-2 (EW) OFF 10 kΩ or higher
B-4 (+1R) - B-2 (EW)
A-10 (WR) - B-2 (EW) WASH Below 1 Ω
A-10 (WR) - B-2 (EW) ON + WASH Below 1 Ω
B-4 (+1R) - B-2 (EW)


If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the intermittent operation. (w/o Intermittent Timing Adjustment)

i.

Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector.


ii.

Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 2 (EW) of the B connector and 4 (+S) of the A connector.


iii.

Turn the wiper switch to the INT position.


iv.

Connect the positive (+) battery lead to terminal 4 (+S) of the A connector for 5 seconds.


v.

Connect the negative (-) battery lead to terminal 4 (+S) of the A connector. Operate the intermittent wiper relay and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

OK:

Refer to the illustration below.


E129662E09
0.156,0.5 1.802,0.896 1.646,0.396 10 false Voltage between terminals A-2 (+1) and B-2 (EW) 3.125,0.01 5.604,0.365 2.479,0.354 10 false Connect the negative (-) battery terminal cable to terminal A-4 (+S) 3.208,0.677 3.854,0.854 0.646,0.177 10 false 10 to 14 V 3.896,1.156 4.188,1.333 0.292,0.177 10 false 0 V 3.906,1.458 5.063,1.635 1.156,0.177 10 false 2.3 to 4.3 seconds

If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the intermittent operation. (w/ Intermittent Timing Adjustment)

i.

Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector.


ii.

Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminals 2 (EW) of the B connector and 4 (+S) of the A connector.


iii.

Turn the wiper switch to the INT position.


iv.

Connect the positive (+) battery lead to terminal 4 (+S) of the A connector for 5 seconds.


v.

Connect the negative (-) battery lead to terminal 4 (+S) of the A connector. Operate the intermittent wiper relay and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

OK:

Refer to the illustration below.


E258319E05
2.438,0.313 4.802,0.708 2.365,0.396 10 false FAST: Connect the negative (-) battery terminal cable to terminal A-4 (+S) 4.688,0.938 7.125,1.521 2.438,0.583 10 false SLOW: Connect the negative (-) battery terminal cable to terminal A-4 (+S) 0.073,2.167 1.771,2.719 1.698,0.552 10 false Voltage between terminals A-2 (+1) and B-2 (EW) 1.667,1.781 2.615,2.073 0.948,0.292 10 false 11 to 14 V 2.177,2.26 2.75,2.635 0.573,0.375 10 false 0 V 2.344,2.76 3.875,3.063 1.531,0.302 10 false 0.6 to 2.6 seconds 4.583,2.76 6.083,3.083 1.5,0.323 10 false 5.7 to 15.7 seconds

If the result is not as specified, replace the windshield wiper switch assembly.



d.

Check the operation (front washer).

i.

Turn the wiper switch off.


ii.

Connect the positive (+) battery lead to terminal 3 (+B) of the A connector and the negative (-) battery lead to terminal 4 (+S) of the A connector and 2 (EW) of the B connector.


iii.

Connect the positive (+) voltmeter terminal to terminal 2 (+1) of the A connector and the negative (-) voltmeter terminal to terminal 2 (EW) of the B connector. Turn the washer switch on and off, and check the voltage between terminals 2 (+1) of the A connector and 2 (EW) of the B connector.

OK:

Refer to the illustration below.


E273971E01
4,1.302 4,1.177 false 4.865,1.302 4.667,1.167 false 3.583,0.385 3.885,0.615 0.302,0.229 10 false ON 3.552,0.552 3.896,0.781 0.344,0.229 10 false OFF 3.25,0.792 3.948,0.969 0.698,0.177 10 false 10 to 14 V 3.573,1.042 3.854,1.208 0.281,0.167 10 false 0 V 4.229,0.083 5.25,0.25 1.021,0.167 10 false Washer Switch 2.542,1.313 4.281,1.51 1.74,0.198 10 false Approximately 0.5 seconds 4.688,1.302 6.427,1.5 1.74,0.198 10 false Approximately 2.2 seconds 0.188,0.333 1.833,0.688 1.646,0.354 10 false Voltage between terminals A-2 (+1) and B-2 (EW)

If the result is not as specified, replace the windshield wiper switch assembly.