Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR › 2014.03–2017.10
RM30M0E _59 Vehicle Exterior _017125 WIPER / WASHER _0116750 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
E276774C01
1.313,0.719 1.719,1.25 1.719,1.25 2.135,0.719 true 1.656,1.281 1.969,1.438 0.313,0.156 10 false *a
*a Lip of Rear Wiper Motor Grommet


Apply MP grease to the entire surface of the rear wiper motor grommet lip.

HINT:

Make sure that the hole does not get clogged with MP grease and the grooves on the lip are filled with MP grease.



b.

Install the rear wiper motor grommet.


Hide 85110R 2.INSTALL REAR WIPER MOTOR ASSEMBLY

a.
E276762E05
1.781,2 1.521,1.76 true 2.969,1.073 2.76,0.74 true 0.344,0.594 0.625,0.115 true 1.833,1.938 1.99,2.135 0.156,0.198 10 false A 2.615,0.625 2.771,0.823 0.156,0.198 10 false B 0.677,0 0.833,0.198 0.156,0.198 10 false C

Set the rear wiper motor assembly in place and temporarily tighten the bolt A.


b.

Install the bolt B.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Fully tighten the bolt A.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.

Install the bolt C.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Connect the connector.


Hide 67754G 3.INSTALL BACK DOOR TRIM SPACER

a.

Engage the 3 clips to install the back door trim spacer.


b.

w/ Smart Entry and Start System:

i.

Connect the connector.



Hide 67751 4.INSTALL BACK DOOR TRIM BOARD

Hide 5.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
E286762C01
1.573,1.104 1.104,0.677 true 0.927,0.552 1.24,0.75 0.313,0.198 10 false *a
*a Wiper Arm Serration


When reusing the rear wiper arm and blade assembly:

i.

Clean the wiper arm serrations.

NOTICE:

Do not grind down the wiper arm serrations.




b.
E292959C01
2.094,1.167 2.51,0.75 true 2.552,0.656 2.865,0.813 0.313,0.156 10 false *a
*a Wiper Pivot Serration


When reusing the rear wiper motor assembly:

i.

Clean the wiper pivot serrations with a wire brush.

NOTICE:

Do not grind down the wiper pivot serrations.




c.

Operate the wiper, and then stop the rear wiper motor assembly in the automatic stop position.


d.
E285918C01
2.76,1.146 2.594,0.917 false 2.427,0.802 2.74,0.958 0.313,0.156 10 false *a
*a Ceramic Dot


Align the blade tip with the ceramic dot on the back window glass, as shown in the illustration.


e.

Install the rear wiper arm and blade assembly with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 85292A 6.INSTALL REAR WIPER ARM HEAD CAP

a.

Engage the 2 hinges and 2 claws to install the rear wiper arm head cap.