Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE(for Hatchback) › 2014.03–2017.10
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0118069 NAME PLATE(for Hatchback) A

EXTERIOR PANELS / TRIM  NAME PLATE(for Hatchback)  INSTALLATION  


PROCEDURE

Hide 75443 1.INSTALL NO. 3 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 3 back door name plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 3 back door name plate as shown in the illustration.

B369995
6.094,1.99 6.344,2.063 false 4.469,2.479 4.854,2.135 true 4.281,2.417 4.594,2.573 0.313,0.156 10 false *a 4.813,0.583 5.063,0.781 0.25,0.198 10 false A 5.906,1.906 6.219,2.063 0.313,0.156 10 false *a 6.125,0.594 6.375,0.792 0.25,0.198 10 false B 5.344,2.042 5.594,2.24 0.25,0.198 10 false C 6.75,2.198 7,2.396 0.25,0.198 10 false D
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 49.2 mm (1.94 in.) B 94.0 mm (3.70 in.)
C 97.6 mm (3.84 in.) D 159.4 mm (6.28 in.)


NOTICE:

Install the No. 3 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 3 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 3 back door name plate.



Hide 75444 2.INSTALL NO. 4 LUGGAGE COMPARTMENT DOOR PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 4 luggage compartment door plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

for Type A:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B369991
5.229,2.229 5.417,2.625 false 5.906,4.333 6.125,4.469 false 4.229,4.594 4.646,4.385 true 6.083,0.333 6.24,0.531 0.156,0.198 10 false A 6.729,1.552 6.885,1.75 0.156,0.198 10 false B 5.896,2.438 6.052,2.635 0.156,0.198 10 false C 4.771,3.188 4.927,3.385 0.156,0.198 10 false D 5.938,3.198 6.094,3.396 0.156,0.198 10 false E 6.583,4.594 6.74,4.792 0.156,0.198 10 false G 5.156,4.604 5.313,4.802 0.156,0.198 10 false F 5.063,2.146 5.375,2.344 0.313,0.198 10 false *a 5.75,4.24 6.063,4.438 0.313,0.198 10 false *a 4.063,4.531 4.375,4.729 0.313,0.198 10 false *a
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 42.2 mm (1.66 in.) B 97.9 mm (3.85 in.)
C 82.1 mm (3.23 in.) D 73.4 mm (2.89 in.)
E 72.6 mm (2.86 in.) F 140.4 mm (5.53 in.)
G 131.6 mm (5.18 in.) - -


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




c.

for Type B:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B369992
5.281,2.271 5.438,2.635 false 5.896,4.229 6.125,4.417 false 4.354,4.75 4.74,4.573 true 6.083,0.333 6.24,0.531 0.156,0.198 10 false A 6.729,1.552 6.885,1.75 0.156,0.198 10 false B 5.885,2.417 6.042,2.615 0.156,0.198 10 false C 4.76,3.198 4.917,3.396 0.156,0.198 10 false D 5.917,3.198 6.073,3.396 0.156,0.198 10 false E 5.177,4.573 5.333,4.771 0.156,0.198 10 false F 6.594,4.563 6.75,4.76 0.156,0.198 10 false G 5.115,2.167 5.396,2.385 0.281,0.219 10 false *a 4.188,4.667 4.469,4.885 0.281,0.219 10 false *a 5.719,4.146 6,4.365 0.281,0.219 10 false *a
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 42.6 mm (1.68 in.) B 98.7 mm (3.89 in.)
C 82.2 mm (3.24 in.) D 73.3 mm (2.89 in.)
E 73.0 mm (2.87 in.) F 140.4 mm (5.53 in.)
G 131.8 mm (5.19 in.) - -


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




d.

for Type C:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B369993
6.188,4.26 5.927,4.083 false 5.469,2.615 5.292,2.323 false 4.667,4.417 4.26,4.604 true 5.125,2.229 5.438,2.385 0.313,0.156 10 false *a 5.76,4.031 6.073,4.188 0.313,0.156 10 false *a 4.01,4.594 4.323,4.75 0.313,0.156 10 false *a 6.135,0.344 6.438,0.5 0.302,0.156 10 false A 6.729,1.406 7.031,1.563 0.302,0.156 10 false B 5.906,2.427 6.208,2.583 0.302,0.156 10 false C 4.781,3.219 5.083,3.375 0.302,0.156 10 false D 5.99,3.177 6.292,3.333 0.302,0.156 10 false E 5.188,4.531 5.49,4.688 0.302,0.156 10 false F 6.583,4.458 6.885,4.615 0.302,0.156 10 false G
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 46.1 mm (1.81 in.) B 108.3 mm (4.26 in.)
C 79.3 mm (3.12 in.) D 76.1 mm (3.00 in.)
E 76.3 mm (3.00 in.) F 140.2 mm (5.52 in.)
G 148.4 mm (5.84 in.) - -


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




e.

for Type D:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B370700
6.042,0.531 5.948,0.25 5.948,0.25 6.51,0.542 true 6.042,3.271 5.969,2.979 5.969,2.979 6.51,3.281 true 5.771,0.156 6.083,0.313 0.313,0.156 10 false *a 4.104,1.406 4.323,1.594 0.219,0.188 10 false A 5.781,2.906 6.094,3.063 0.313,0.156 10 false *a 5.875,1.219 6.094,1.406 0.219,0.188 10 false B 6.677,1.198 6.896,1.385 0.219,0.188 10 false C 5.625,2.625 5.844,2.813 0.219,0.188 10 false D 4.115,4.198 4.333,4.385 0.219,0.188 10 false E 5.854,3.979 6.073,4.167 0.219,0.188 10 false F 6.677,3.99 6.896,4.177 0.219,0.188 10 false G 5.615,5.354 5.833,5.542 0.219,0.188 10 false H
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 126.9 mm (5.00 in.) B 51.1 mm (2.01 in.)
C 114.4 mm (4.50 in.) D 93.8 mm (3.69 in.)
E 126.9 mm (4.99 in.) F 51.2 mm (2.02 in.)
G 114.2 mm (4.50 in.) H 93.9 mm (3.70 in.)


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




Hide 75442A 3.INSTALL NO. 2 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 2 back door name plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

for Type A:

i.

Install a new No. 2 back door name plate as shown in the illustration.

B348151
4.292,2.802 4.729,3.083 false 5.385,1.552 5.573,1.167 false 3.979,1.563 4.135,1.76 0.156,0.198 10 false A 6.802,1.615 6.958,1.813 0.156,0.198 10 false C 5.302,0.646 5.458,0.844 0.156,0.198 10 false B 4.563,2.615 4.719,2.813 0.156,0.198 10 false D 4.771,3.104 5.083,3.302 0.313,0.198 10 false *a 5.281,1.583 5.594,1.781 0.313,0.198 10 false *a
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 139.9 mm (5.51 in.) B 231.1 mm (9.10 in.)
C 74.4 mm (2.93 in.) D 35.2 mm (1.39 in.)


NOTICE:

Install the No. 2 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 2 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 back door name plate.




c.

for Type B:

i.

Install a new No. 2 back door name plate as shown in the illustration.

B369994
6.427,0.938 6.146,0.5 6.146,0.5 6.708,0.948 true 5.979,0.406 6.292,0.563 0.313,0.156 10 false *a 5.396,0.708 5.604,0.896 0.208,0.188 10 false B 4,1.76 4.208,1.948 0.208,0.188 10 false A 6.854,1.521 7.063,1.708 0.208,0.188 10 false C 6.26,3.177 6.469,3.365 0.208,0.188 10 false D
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 77.9 mm (3.07 in.) B 218.4 mm (8.60 in.)
C 116.6 mm (4.59 in.) D 25.3 mm (1.00 in.)


NOTICE:

Install the No. 2 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 2 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 back door name plate.




Hide 75441E 4.INSTALL NO. 1 BACK DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body panel or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 1 back door name plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 1 back door name plate as shown in the illustration.

B343962
4.052,0.854 4.625,0.563 4.625,0.563 4.323,0.833 true 4.281,2.542 4.083,2.354 4.083,2.354 4.313,2.229 false 4.667,0.458 4.979,0.615 0.313,0.156 10 false *a 4.323,1.385 4.594,1.594 0.271,0.208 10 false A 4.479,3.083 4.75,3.292 0.271,0.208 10 false B 5.146,3.438 5.417,3.646 0.271,0.208 10 false C 6.677,1.74 6.948,1.948 0.271,0.208 10 false D 3.927,2.281 4.24,2.438 0.313,0.156 10 false *a
*a Radius End Point of Back Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 117.6 mm (4.63 in.) B 9.1 mm (0.358 in.)
C 140.0 mm (5.51 in.) D 108.5 mm (4.27 in.)


NOTICE:

Install the No. 1 back door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 1 back door name plate to 20 to 30°C (68 to 86°F) and install the No. 1 back door name plate.



Hide 75741E 5.INSTALL SYMBOL EMBLEM

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the symbol emblem with any double-sided tape remaining on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B348152
0.406,3.552 0.74,3.552 true 2.583,3.802 2.917,3.802 true 2.969,3.698 3.25,3.938 0.281,0.24 10 false *a 0.229,3.458 0.51,3.698 0.281,0.24 10 false *a
*a Location Pin


Insert the 2 location pins into the vehicle body and install a new symbol emblem.

NOTICE:

Install the symbol emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the symbol emblem to 20 to 30°C (68 to 86°F) and install the symbol emblem.