Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › ROOF DRIP SIDE FINISH MOULDING(for Hatchback) › from 2014.03
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0118072 ROOF DRIP SIDE FINISH MOULDING(for Hatchback) A

EXTERIOR PANELS / TRIM  ROOF DRIP SIDE FINISH MOULDING(for Hatchback)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the LH and RH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 75561 1.INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP

NOTICE:

When installing new No. 1 roof drip side finish moulding clips, remove the double-sided tape remaining where the No. 1 roof drip side finish moulding clips will be installed on the vehicle body and clean the vehicle body with non-residue solvent.


a.
B229383
2.125,0.229 2.396,0.479 false 1.292,0.875 1.635,1.135 true 1.99,0.073 2.302,0.271 0.313,0.198 10 false *a 1.135,0.719 1.448,0.917 0.313,0.198 10 false *b
*a Adhesive
*b 2 to 3 mm bead of adhesive


Apply a 2 to 3 mm (0.0787 to 0.118 in.) bead of adhesive to 2 new No. 1 roof drip side finish moulding clips.

HINT:

Adhesive strength (tensile strength): 13.7 MPa (140.0 kgf/cm2, 1987 psi) or more (when the temperature is 23°C (73°F).)



b.
B348156
0.448,3.438 0.677,3.698 0.229,0.26 10 false E 1.073,3.438 1.302,3.698 0.229,0.26 10 false F 1.99,3.521 2.219,3.781 0.229,0.26 10 false D 2.5,3.385 2.729,3.646 0.229,0.26 10 false D 2.125,0.271 2.354,0.531 0.229,0.26 10 false C 2.656,0.292 2.885,0.552 0.229,0.26 10 false C 0.427,0.25 0.656,0.51 0.229,0.26 10 false A 1.052,0.26 1.281,0.521 0.229,0.26 10 false B

Install the No. 1 roof drip side finish moulding clips to the positions on the roof panel shown in the illustration. Determine the locations and firmly press and install the 2 No. 1 roof drip side finish moulding clips after lightly applying adhesive.

Standard Dimension:
Dimension Measurement
A 3.1 mm (0.122 in.)
B 1.2 to 2.2 mm (0.0473 to 0.0866 in.)
C 4.0 mm (0.157 in.)
D 3.5 mm (0.138 in.)
E 4.7 mm (0.185 in.)
F 1.0 to 2.0 mm (0.0394 to 0.0787 in.)



c.

Install the roof drip side finish moulding when 20 minutes or more have elapsed after pressing and installing the 2 No. 1 roof drip side finish moulding clips.

HINT:
·

Initial hardening time: 20 minutes

·

Complete hardening time: 48 hours




Hide 75552E 2.INSTALL ROOF DRIP SIDE FINISH MOULDING

a.

Engage the 2 clips and install the roof drip side finish moulding.


b.

Remove the protective tape.