Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.04–2017.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  FAIL-SAFE CHART  


FAIL-SAFE FUNCTION


a.

When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.


b.

The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)

Function Control Master System Related Fail-safe Operation Driver Detectable DTC Detection
(ECU that stored DTC)
Anti-lock Brake System Control
·

Prevents the wheels from locking during sudden stops.


Brake actuator assembly Brake actuator assembly
·

During control: When back-up control (stabilizing the vehicle) is complete, the system changes to normal braking and prohibits control.

·

Not during control: Control cannot be performed.


ABS warning light illuminates.
·

U0073

·

U0124


(Brake actuator assembly)
Vehicle Stability Control/Traction Control
·

Suppresses vehicle instability, such as sliding sideways when cornering and wheel slippage when accelerating from rest.


Brake actuator assembly
·

ECM

·

Spiral cable with sensor sub-assembly

·

Airbag ECU assembly


·

During control: After ending backup control (stabilizing the vehicle), the system changes to normal braking and prohibits control.

·

Not during control: Control cannot start.


·

ABS warning light illuminates.

·

Brake warning light illuminates.

·

Slip indicator light illuminates.


·

U0073

·

U0100

·

U0124

·

U0126


(Brake actuator assembly)
Air Conditioning Control
·

Corrects engine speed, such as for idle up.

·

Controls outlet air temperature, outlet mode change and airflow volume based on engine coolant temperature signal.

·

Corrects engine coolant temperature map and changes compressor lock judgment value.


Air conditioning amplifier assembly ECM
·

Control is performed based on default coolant temperature of 80°C (176°F).

·

Control is performed based on engine model (differs between vehicle models).


- U0100
(Air conditioning amplifier assembly)
Compressor Control
·

Determines whether the compressor is locked using engine speed information.


Air conditioning amplifier assembly ECM Control is performed based on default engine speed of 0 rpm. - U0100
(Air conditioning amplifier assembly)
Ambient Temperature Correction Control
·

Switches air conditioning system operation condition and corrects value of displayed ambient temperature according to vehicle speed signal.


Air conditioning amplifier assembly Combination meter assembly Control is performed based on default vehicle speed of 0 km/h (0 mph).
·

Correction level for displayed ambient temperature declines.

·

Correction level for outlet airflow declines.


U0155
(Air conditioning amplifier assembly)
Smart Function
·

Smart warning buzzer


Certification ECU (Smart key ECU assembly) Combination meter assembly - Smart warning buzzer does not operate. -
Tachometer
·

Displays information on the tachometer.


Combination meter assembly ECM Control is performed based on signal value of 0.
·

The tachometer displays 0 rpm.

·

The drive monitor stops calculating.


U0100
(Combination meter assembly)
Airbag Warning
·

Airbag warning light control.


Combination meter assembly Airbag ECU assembly Control is performed based on signal value of "Active". Airbag warning light illuminates. U0151
(Combination meter assembly)
Engine Coolant Temperature Receiver Gauge Control Combination meter assembly ECM Control is performed based on signal value of 0. Water temperature hot warning light illuminates. -
Engine Start/Stop Switch (Power Source Mode Change)
·

Using start/stop switch signal as trigger, changes power source mode automatically and requests starter operation when conditions are met.


Certification ECU (Smart key ECU assembly) ECM - - U0100
(Certification ECU (Smart key ECU assembly))
Engine Start Control
·

Allows the engine to start by pressing the engine switch once. (Cranking hold)


Certification ECU (Smart key ECU assembly) ECM Cranking is stopped when engine starting is judged based on an engine speed signal received via direct line. - U0100
(Certification ECU (Smart key ECU assembly))
TC DTC Output Service
·

While TC = ON is being received from the ECM, a DTC is output in response to the request from the combination meter assembly.


Combination meter assembly
·

ECM

·

Airbag ECU assembly


If the TC signal is lost during TC service (TC = ON), the TC is determined to be OFF and TC service ends. - -
Collision Detection Signal
·

Notifies the system of a collision in order to perform fuel cut when a vehicle collision occurs.


ECM Airbag ECU assembly - - -
Airbag Warning Light Control
·

Sends airbag warning light illumination information.


Combination meter assembly Airbag ECU assembly - - -
Trigger Signal/Autonomous Transmission
·

Outputs the yaw rate sensor signal.


Airbag ECU assembly Brake actuator assembly The yaw rate sensor information signal is sent at regular intervals every 0.012 seconds. - -
Event Data Recorder (EDR)
·

Records conditions, such as the vehicle speed, the amount the accelerator is depressed, and the shift lever position when the event data recorder recording conditions are met.


Airbag ECU assembly
·

ECM

·

Brake actuator assembly

·

Spiral cable with sensor sub-assembly

·

Combination meter assembly


·

An invalid value is recorded in the EDR.

·

Maintains previous values.


- -
Air Conditioning Coordinated Control
·

Performs idle up according to the compressor load.

·

Performs air conditioning cut control.


ECM Air conditioning amplifier assembly Air conditioning coordinated control does not operate (cannot perform idle up). Air conditioning does not operate. -
Charging Control
·

Performs idle up according to charging requests.


ECM Air conditioning amplifier assembly
·

Idle up according to charging requests is not performed.

·

Charging control is not prohibited.


·

Idle up according to charging requests is not performed.

·

The taillights flicker.

·

The blower airflow volume changes.


-
Eco Driving Indicator
·

Displays information to the driver to encourage Eco-driving.


ECM Combination meter assembly - No information is displayed. -
Integrated Control (VDM)
·

Estimates the driver requested torque based on the accelerator pedal operation and performs torque characteristic control according to driving conditions so that driveability, acceleration performance and acceleration feeling are improved.


ECM
·

Brake actuator assembly

·

Spiral cable with sensor sub-assembly


Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, driveability, acceleration performance and acceleration feeling are not improved. Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, driveability, acceleration performance and acceleration feeling are not improved. -
Steering Angle Sensor
·

Detects the vehicle steering angle.


Spiral cable with sensor sub-assembly Brake actuator assembly The steering angle sensor information signal is sent at regular intervals every 0.12 seconds. - -