Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.04–2016.07
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to +B (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Combination meter assembly

·

Airbag ECU assembly*1

·

Brake actuator assembly*2

·

ECM

·

Certification ECU (smart key ECU assembly)*3

·

Air conditioning amplifier assembly*4

·

Spiral cable with sensor sub-assembly*5

·

No. 1 CAN junction connector



*1: w/ Airbag System

*2: w/ ABS

*3: w/ Smart Entry and Start System

*4: for Automatic Air Conditioning System, for Manual Air Conditioning System with 1NR-FE or for Manual Air Conditioning System with 2NR-FE

*5: w/ VSC


WIRING DIAGRAM

E340832E01
0.115,0.083 1.031,0.281 0.917,0.198 10 false V Bus: 0.25,0.5 2.854,0.698 2.604,0.198 10 false x: Suspected Area 3.354,0.177 4.125,0.375 0.771,0.198 10 false 120 Ω 4.552,0.448 5.01,0.646 0.458,0.198 10 false ECM 2.656,0.802 3.271,1 0.615,0.198 10 false CANL 4.063,0.802 4.677,1 0.615,0.198 10 false CANH 2.979,0.99 3.438,1.188 0.458,0.198 10 false F81 2.979,1.167 3.438,1.365 0.458,0.198 10 false F82 2.948,1.344 3.406,1.542 0.458,0.198 10 false F130 3.917,0.99 4.375,1.188 0.458,0.198 10 false F81 3.917,1.167 4.375,1.365 0.458,0.198 10 false F82 3.875,1.344 4.333,1.542 0.458,0.198 10 false F130 2.677,1.344 2.99,1.542 0.313,0.198 10 false 14 2.677,1.167 2.99,1.365 0.313,0.198 10 false 34 2.76,0.99 3.073,1.188 0.313,0.198 10 false 7 4.292,1.01 4.604,1.208 0.313,0.198 10 false 8 4.281,1.188 4.594,1.385 0.313,0.198 10 false 33 4.271,1.354 4.583,1.552 0.313,0.198 10 false 13 3.344,1.344 3.656,1.542 0.313,0.198 10 false *3 3.344,1.167 3.656,1.365 0.313,0.198 10 false *2 3.344,0.99 3.656,1.188 0.313,0.198 10 false *1 3.615,1.344 3.885,1.531 0.271,0.188 10 false *3 3.615,1.167 3.865,1.344 0.25,0.177 10 false *2 3.604,0.99 3.865,1.177 0.26,0.188 10 false *1 4.333,2.156 4.792,2.354 0.458,0.198 10 false F62 4.333,2.323 6.625,2.646 2.292,0.323 10 false No. 1 CAN Junction Connector 2.833,1.75 3.115,1.969 0.281,0.219 10 false W 4.146,1.75 4.448,2 0.302,0.25 10 false BE 2.885,1.958 3.198,2.156 0.313,0.198 10 false 14 4.115,1.938 4.427,2.135 0.313,0.198 10 false 3 4.323,3.24 4.635,3.438 0.313,0.198 10 false 18 4.323,2.885 4.635,3.083 0.313,0.198 10 false 7 4.323,4.698 4.635,4.896 0.313,0.198 10 false 19 4.323,4.344 4.635,4.542 0.313,0.198 10 false 8 4.802,2.833 5.083,3.052 0.281,0.219 10 false L 4.771,3.188 5.052,3.406 0.281,0.219 10 false W 4.792,4.292 5.073,4.51 0.281,0.219 10 false V 4.771,4.646 5.052,4.865 0.281,0.219 10 false W 5.177,2.885 5.49,3.083 0.313,0.198 10 false 40 5.177,3.24 5.49,3.438 0.313,0.198 10 false 18 5.177,4.344 5.49,4.542 0.313,0.198 10 false 11 5.177,4.698 5.49,4.896 0.313,0.198 10 false 12 5.479,2.885 6.094,3.083 0.615,0.198 10 false CANH 5.479,3.24 6.094,3.438 0.615,0.198 10 false CANL 5.104,3.521 5.719,3.719 0.615,0.198 10 false F44 5.104,3.688 6.938,4.052 1.833,0.365 10 false Certification ECU (Smart Key ECU Assembly)*10 5.479,4.344 6.094,4.542 0.615,0.198 10 false TX+ 5.479,4.698 6.094,4.896 0.615,0.198 10 false TX- 4.688,5.146 6.677,5.344 1.99,0.198 10 false F3*12, F124*13 4.698,5.313 7.156,5.719 2.458,0.406 10 false Air Conditioning Amplifier Assembly*11 2.635,2.51 2.948,2.708 0.313,0.198 10 false 15 2.708,2.156 3.021,2.354 0.313,0.198 10 false 4 2.635,3.969 2.948,4.167 0.313,0.198 10 false 13 2.708,3.615 3.021,3.813 0.313,0.198 10 false 2 2.24,2.104 2.521,2.323 0.281,0.219 10 false B 2.219,2.458 2.5,2.677 0.281,0.219 10 false W 2.219,3.917 2.5,4.135 0.281,0.219 10 false W 2.25,3.563 2.531,3.781 0.281,0.219 10 false L 1.25,2.156 1.865,2.354 0.615,0.198 10 false CANH 1.25,2.51 1.865,2.708 0.615,0.198 10 false CANL 1.25,3.969 1.865,4.167 0.615,0.198 10 false CANL 1.25,3.615 1.865,3.813 0.615,0.198 10 false CANH 0.219,2.948 0.833,3.146 0.615,0.198 10 false F21 0.229,3.115 3.438,3.313 3.208,0.198 10 false Airbag ECU Assembly*4 0.188,4.406 2.333,4.729 2.146,0.323 10 false A49*6, A48*7, A47*8, A35*9 0.188,4.573 4.01,4.771 3.823,0.198 10 false Brake Actuator Assembly*5 1.771,2.156 2.083,2.354 0.313,0.198 10 false 13 1.771,2.51 2.083,2.708 0.313,0.198 10 false 22 1.771,3.615 2.083,3.813 0.313,0.198 10 false 25 1.771,3.969 2.083,4.167 0.313,0.198 10 false 14 4.885,8.219 7.156,8.5 2.271,0.281 10 false : CAN Main Bus Line (CANH) 4.885,8.625 7.156,8.906 2.271,0.281 10 false : CAN Main Bus Line (CANL) 4.885,9.031 7.156,9.313 2.271,0.281 10 false : CAN Branch Line (CANH) 4.885,9.427 7.156,9.708 2.271,0.281 10 false : CAN Branch Line (CANL) 0.198,5.354 2.948,5.854 2.75,0.5 10 false *1: for 1NZ-FE with Manual Transaxle without Air Fuel Ratio Sensor or for 2NZ-FE with Manual Transaxle 0.188,6.333 3.021,6.813 2.833,0.479 10 false *2: for Automatic Transaxle or for 1NZ-FE with Manual Transaxle with Air Fuel Ratio Sensor 0.188,7.021 2.219,7.583 2.031,0.563 10 false *3: for 1NR-FE or 2NR-FE 0.198,7.406 2.229,7.969 2.031,0.563 10 false *4: w/ Airbag System 0.208,7.802 2.208,8.115 2,0.313 10 false *5: w/ ABS 0.208,8.219 2.208,8.531 2,0.313 10 false *6: w/ VSC with CVT 0.198,8.646 2.198,8.958 2,0.313 10 false *7: w/ VSC except CVT 3.177,5.646 5.51,5.896 2.333,0.25 10 false *10: w/ Smart Entry and Start System 3.188,6.115 6.469,6.698 3.281,0.583 10 false *11: for Automatic Air Conditioning System, for Manual Air Conditioning System with 1NR-FE or for Manual Air Conditioning System with 2NR-FE 3.208,7.167 5.958,7.417 2.75,0.25 10 false *12: for Automatic Air Conditioning System 3.208,7.625 5.823,7.958 2.615,0.333 10 false *13: for Manual Air Conditioning System 0.198,9.063 2.198,9.375 2,0.313 10 false *8: w/o VSC with CVT 0.208,9.458 2.208,9.771 2,0.313 10 false *9: w/o VSC except CVT

E340834E01
1.229,0.896 1.844,1.094 0.615,0.198 10 false CANH 0.146,0.094 1.25,0.333 1.104,0.24 10 false V Bus: 0.208,0.427 3.333,0.667 3.125,0.24 10 false x: Suspected Area 1.26,1.229 1.875,1.427 0.615,0.198 10 false CANL 1.76,0.885 1.917,1.083 0.156,0.198 10 false 4 1.76,1.25 1.917,1.448 0.156,0.198 10 false 3 2.229,0.802 2.385,1 0.156,0.198 10 false R 2.219,1.177 2.375,1.375 0.156,0.198 10 false W 2.698,0.875 2.854,1.073 0.156,0.198 10 false 9 2.656,1.229 2.969,1.427 0.313,0.198 10 false 20 0.292,1.677 0.75,1.875 0.458,0.198 10 false F116 0.292,1.823 1.823,2.385 1.531,0.563 10 false Spiral Cable with Sensor Sub-assembly*1 2.833,2.719 2.99,2.917 0.156,0.198 10 false W 4.771,1.875 4.927,2.073 0.156,0.198 10 false W 5.885,1.667 6.5,1.865 0.615,0.198 10 false CANH 6,2 6.615,2.198 0.615,0.198 10 false CANL 6.167,2.25 6.625,2.448 0.458,0.198 10 false F16 6.167,2.385 6.781,2.583 0.615,0.198 10 false DLC3 4.75,1.49 5.063,1.688 0.313,0.198 10 false GR 4.302,1.552 4.458,1.75 0.156,0.198 10 false 1 4.271,1.917 4.583,2.115 0.313,0.198 10 false 12 4.094,2.469 4.25,2.667 0.156,0.198 10 false 6 4.083,3 4.396,3.198 0.313,0.198 10 false 32 2.896,2.448 3.208,2.646 0.313,0.198 10 false 17 2.885,2.99 3.198,3.188 0.313,0.198 10 false 31 2.667,3.208 3.281,3.406 0.615,0.198 10 false CANL 4.083,3.208 4.698,3.406 0.615,0.198 10 false CANH 4.125,2.688 4.333,2.917 0.208,0.229 10 false G 5.646,1.573 5.802,1.771 0.156,0.198 10 false 6 5.667,1.938 5.979,2.135 0.313,0.198 10 false 14 4.583,3.417 5.042,3.615 0.458,0.198 10 false F38 4.583,3.583 6.479,3.948 1.896,0.365 10 false Combination Meter Assembly 3.313,3.771 4.083,3.969 0.771,0.198 10 false 120 Ω 4.927,4.219 6.833,4.458 1.906,0.24 10 false : CAN Main Bus Line (CANH) 4.927,4.594 6.833,4.833 1.906,0.24 10 false : CAN Main Bus Line (CANL) 4.927,5.01 7,5.25 2.073,0.24 10 false : CAN Branch Bus Line (CANH) 4.917,5.417 6.99,5.656 2.073,0.24 10 false : CAN Branch Bus Line (CANL) 0.458,5.417 1.99,5.615 1.531,0.198 10 false *1: w/ VSC 4.354,0.635 4.813,0.833 0.458,0.198 10 false F62 4.354,0.792 6.25,1.115 1.896,0.323 10 false No.1 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.74 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C355431C01
5.604,0.333 6.104,0.583 0.5,0.25 2,0.333 2.5,0.583 0.5,0.25 1.76,1.5 1.25,1.083 true 1.885,1.5 1.25,0.833 true 2,1.5 1.25,0.583 true 1.667,1.5 1.25,1.333 true 1.667,1.75 1.25,1.833 true 1.75,1.75 1.25,2.083 true 1.885,1.75 1.25,2.333 true 2,1.75 1.25,2.583 true 2.281,1.5 3.167,0.583 true 2.396,1.5 3.167,0.833 true 2.51,1.5 3.167,1.083 true 2.625,1.5 3.167,1.333 true 2.625,1.75 3.167,1.833 true 2.51,1.75 3.167,2.083 true 2.396,1.75 3.167,2.333 true 2.281,1.75 3.167,2.583 true 6.167,2.25 6.49,1.802 true 4.333,0.083 4.646,0.24 0.313,0.156 10 false *1 0.104,0.063 0.417,0.219 0.313,0.156 10 false *a 2.135,0.375 2.594,0.573 0.458,0.198 10 false F62 5.729,0.375 6.188,0.573 0.458,0.198 10 false F16 0.698,1.26 1.615,1.458 0.917,0.198 10 false CANH*b 0.698,1 1.615,1.198 0.917,0.198 10 false CANH*c 0.698,0.76 1.615,0.958 0.917,0.198 10 false CANH*d 0.698,0.5 1.615,0.698 0.917,0.198 10 false CANH*e 0.698,1.74 1.615,1.938 0.917,0.198 10 false CANL*b 0.698,2 1.615,2.198 0.917,0.198 10 false CANL*c 0.698,2.24 1.615,2.438 0.917,0.198 10 false CANL*d 0.698,2.49 1.615,2.688 0.917,0.198 10 false CANL*e 3.229,1.26 4.146,1.458 0.917,0.198 10 false CANH*i 3.229,1.01 4.146,1.208 0.917,0.198 10 false CANH*h 3.229,0.76 4.146,0.958 0.917,0.198 10 false CANH*g 3.229,0.51 4.146,0.708 0.917,0.198 10 false CANH*f 3.229,1.75 4.146,1.948 0.917,0.198 10 false CANL*i 3.229,2 4.146,2.198 0.917,0.198 10 false CANL*h 3.229,2.24 4.146,2.438 0.917,0.198 10 false CANL*g 3.229,2.49 4.146,2.688 0.917,0.198 10 false CANL*f 5.833,2.146 6.25,2.344 0.417,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to DLC3
*c to Brake Actuator Assembly*1 *d to ECM
*e to Airbag ECU Assembly*2 *f to Combination Meter Assembly
*g to Certification ECU (Smart Key ECU Assembly)*3 *h to Air Conditioning Amplifier Assembly*4
*i to Spiral Cable with Sensor Sub-assembly*5 - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F62-1 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher DLC3
F62-12 (CANL) - F16-16 (BAT)
F62-2 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake actuator assembly*1
F62-13 (CANL) - F16-16 (BAT)
F62-3 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
F62-14 (CANL) - F16-16 (BAT)
F62-4 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag ECU assembly*2
F62-15 (CANL) - F16-16 (BAT)
F62-6 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
F62-17 (CANL) - F16-16 (BAT)
F62-7 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (smart key ECU assembly)*3
F62-18 (CANL) - F16-16 (BAT)
F62-8 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air conditioning amplifier assembly*4
F62-19 (CANL) - F16-16 (BAT)
F62-9 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Spiral cable with sensor sub-assembly*5
F62-20 (CANL) - F16-16 (BAT)


*1: w/ ABS

*2: w/ Airbag System

*3: w/ Smart Entry and Start System

*4: for Automatic Air Conditioning System, for Manual Air Conditioning System with 1NR-FE or for Manual Air Conditioning System with 2NR-FE

*5: w/ VSC



Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B
NG (DLC3 branch line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect the F62 No. 1 CAN junction connector.


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to Terminals of ECU.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU



c.
C152423C14
1.5,0.146 1.99,0.438 0.49,0.292 1.958,0.906 2.271,0.26 true 1.958,1.49 1.583,1.979 true 2.333,1.458 2.635,1.958 true 2.313,0.167 2.729,0.323 0.417,0.156 10 false CANH 1.208,1.896 1.615,2.042 0.406,0.146 10 false CANL 0.156,0.167 0.323,0.313 0.167,0.146 10 false *1 1.646,0.208 1.906,0.365 0.26,0.156 10 false F16 2.698,1.896 3.115,2.052 0.417,0.156 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-6 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F16-14 (CANL) - F16-16 (BAT)


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR