Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.04–2017.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Spiral cable with sensor sub-assembly branch line or connector

·

Power source circuit of spiral cable with sensor sub-assembly

·

Spiral cable with sensor sub-assembly ground circuit

·

Spiral cable with sensor sub-assembly



WIRING DIAGRAM

E340829E02
2.833,1.438 3.583,0.354 3.583,0.354 3.75,0.354 false 0.115,0.083 1.031,0.281 0.917,0.198 10 false V Bus: 2.094,0.667 2.708,0.865 0.615,0.198 10 false DLC3 0.74,2.344 1.51,2.542 0.771,0.198 10 false 120 Ω 6.104,2.344 6.875,2.542 0.771,0.198 10 false 120 Ω 0.698,2.969 1.313,3.167 0.615,0.198 10 false F130 0.698,3.135 1.313,3.333 0.615,0.198 10 false ECM 5.719,2.958 6.333,3.156 0.615,0.198 10 false F38 5.719,3.125 6.938,3.708 1.219,0.583 10 false Combination Meter Assembly 3.906,3.74 4.521,3.938 0.615,0.198 10 false CANH 4.458,3.74 5.073,3.938 0.615,0.198 10 false CANL 3.938,3.51 4.094,3.708 0.156,0.198 10 false 4 4.49,3.51 4.646,3.708 0.156,0.198 10 false 3 3.49,3.927 3.646,4.125 0.156,0.198 10 false 6 3.49,4.458 3.646,4.656 0.156,0.198 10 false 5 5.156,4.083 5.313,4.281 0.156,0.198 10 false 2 4.719,4.198 5.333,4.396 0.615,0.198 10 false ESS 3.729,4.021 4.344,4.219 0.615,0.198 10 false BAT 3.729,4.552 4.344,4.75 0.615,0.198 10 false IG1 2.958,4.167 3.573,4.365 0.615,0.198 10 false DOME 2.854,4.698 3.573,4.885 0.719,0.188 10 false IG1 NO. 2 1.615,4.01 3.448,4.208 1.833,0.198 10 false from Battery 0.583,4.563 2.417,5.396 1.833,0.833 10 false from Ignition or Starter Switch Assembly*1 or No. 1 Ignition Relay*2 3.594,4.875 4.052,5.073 0.458,0.198 10 false F116 3.594,5.042 5.135,5.448 1.542,0.406 10 false Spiral Cable with Sensor Sub-assembly 5.719,4.448 6.823,4.708 1.104,0.26 10 false Trouble Area 0.5,6.083 6,6.281 5.5,0.198 10 false *1: w/o Smart Entry and Start System 0.5,6.417 6,6.615 5.5,0.198 10 false *2: w/ Smart Entry and Start System 4.313,6.938 7.156,7.219 2.844,0.281 10 false : CAN Branch Line (CANH) 4.313,7.354 7.156,7.635 2.844,0.281 10 false : CAN Branch Line (CANL) 1.167,6.938 4.01,7.219 2.844,0.281 10 false : CAN Main Bus Line (CANH) 1.167,7.354 4.01,7.635 2.844,0.281 10 false : CAN Main Bus Line (CANL) 3.823,0.271 4.281,0.469 0.458,0.198 10 false F62 3.823,0.438 6.135,0.75 2.313,0.313 10 false No. 1 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.74 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C328891C10
1.458,0.833 1.958,1.083 0.5,0.25 1.333,2.5 1.583,2 true 2.083,2.5 1.833,2 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.552,0.875 2.01,1.073 0.458,0.198 10 false F116 1.146,2.531 1.76,2.729 0.615,0.198 10 false CANL 1.917,2.531 2.531,2.729 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)


Disconnect the spiral cable with sensor sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F116-4 (CANH) - F116-3 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C328891C11
1.458,0.833 1.958,1.083 0.5,0.25 1.125,2.5 1.375,2 true 2.469,2.5 2.219,2 true 1.708,2.5 1.958,2 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.563,0.875 2.021,1.073 0.458,0.198 10 false F116 0.99,2.531 1.604,2.729 0.615,0.198 10 false ESS 2.375,2.531 2.99,2.729 0.615,0.198 10 false BAT 1.615,2.531 2.229,2.729 0.615,0.198 10 false IG1
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F116-2 (ESS) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F116-5 (IG1) - Body ground Ignition switch ON 11 to 14 V
F116-6 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)