Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2016.04–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.



CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES


a.

Freeze frame data is stored when the brake system operates. The freeze frame data is updated each time the system operates.


b.

Once freeze frame data is stored when the system operates, it is not cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the system was activated can be stored and displayed.

HINT:
·

When the vehicle is stopped (vehicle speed below 7 km/h (4.3 mph)), turning the ignition switch from off to ON does not cause the value to increase.

·

The value "31" is displayed when the ignition switch was turned to ON more than 31 times.




d.

Check freeze frame data when the system operates

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3 and turn the ignition switch to ON.


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility.


iv.

Select "ABS History".

Chassis > ABS/VSC/TRC > Utility
Tester Display
ABS History
50005 105 8

v.

Check the freeze frame data when the system operates.




CHECK FREEZE FRAME DATA WHEN DTC WAS STORED


a.

Freeze frame data is stored when a DTC is output.


b.

Once freeze frame data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the ignition switch has been turned from off to ON since a DTC was output can be stored and displayed.

HINT:

The value "31" is displayed when the ignition switch was turned to ON more than 31 times.



d.

Check freeze frame data when DTC is output

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3 and turn the ignition switch to ON.


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

iv.

Select a DTC to display the freeze frame data.


v.

Check the freeze frame data for the output DTC.

Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Number of IG ON Number of times ignition switch turned to ON after Freeze Frame Data stored 0 to 31 - -
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Gear Position Gear position information P, N, R, 1st-6th, Fail or Not R Actual gear position -
Shift Lever Position Shift lever position information P, N, R, D/M, 1st-6th/B or Fail Actual shift lever position -
Operated System Operated system status ABS, VSC, TRC, BA, HAB, PBA, PB, HA-CTRL, TSC, Fail, Sys or Non Actual operated system ABS: ABS activated
VSC: VSC activated
TRC: TRC activated
BA: BA activated
HAB: High power assist brake activated*
PBA: PBA activated*
PB: PB activated*
HA-CTRL: Hill-start assist control activated*
TSC: Trailer sway control activated*
Fail: Fail-safe mode activated
Sys: System prohibit activated
Non: No operation activated
Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.30 to 0.80 V Reading increases when brake pedal is depressed
M/C Sensor Grade Master cylinder pressure sensor change Min.: -30 MPa/s, Max.: 225 MPa/s Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with pedal movement speed
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Lateral G Lateral G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and backward G Min.: - 25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle speed grade Min.: -25.10 m/s2, Max.: 24.90 m/s2 Vehicle stopped: 0.00 m/s2 During driving: Changes in proportion with vehicle acceleration/deceleration
Real Engine Torque Real engine torque Min.: -1024.0 Nm, Max.: 1023.0 Nm - -
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%, Max.: 128.0% Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
IG1 Voltage Value IG1 voltage value Min.: 0.00 V, Max.: 20.00 V Ignition switch to ON: 11.00 to 14.00 V -
Inspection Mode Inspection mode Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Steering Angle Sensor Steering angle sensor Min.: - 3276.8°, Max.: 3276.7° Turning left: Increases
Turning right: Decreases
-
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Elapsed Time after Freeze Trigger Elapsed time after freeze trigger Min.: 0 msec, Max.: 500 msec - -

*: Not supported





CLEAR FREEZE FRAME DATA


NOTICE:

Clearing the DTC will also clear the Freeze Frame Data.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTC and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105