Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.04
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the yaw rate and acceleration sensor (airbag ECU assembly).

The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1381 Acceleration Sensor Power Supply Voltage Malfunction Vehicle speed is 3 km/h (2 mph) or higher and yaw rate and acceleration sensor power supply malfunction signal is received for 10 seconds or more.
·

Yaw rate and acceleration sensor power source circuit

·

Yaw rate and acceleration sensor (airbag ECU assembly)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor (airbag ECU assembly), perform acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
C233304C21
1.521,0.271 1.969,0.552 0.448,0.281 1.125,1.469 0.563,1.469 true 0.24,1.375 0.49,1.552 0.25,0.177 10 false IG2 0.146,0.073 0.333,0.229 0.188,0.156 10 false *a 1.635,0.323 2,0.531 0.365,0.208 10 false F21
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the yaw rate and acceleration sensor (airbag ECU assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F21-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C233304C22
1.521,0.271 2.01,0.563 0.49,0.292 1.813,1.542 2.125,1.802 true 1.667,1.542 1.375,1.802 true 1.229,1.833 1.427,2.01 0.198,0.177 10 false E1 2.052,1.833 2.25,2.01 0.198,0.177 10 false E2 0.146,0.073 0.333,0.229 0.188,0.156 10 false *a 1.656,0.344 2.021,0.542 0.365,0.198 10 false F21
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-25 (E1) - Body ground Always Below 1 Ω
F21-26 (E2) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)