Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.04
RM30M0E _51 Engine / Hybrid System _052909 CRUISE CONTROL _0256264 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter self-diagnostic mode.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E269391E38
1.281,1.115 1.594,1.313 0.313,0.198 10 false TC 0.906,3.417 1.417,3.677 0.51,0.26 10 false DLC3 0.917,3.26 1.229,3.458 0.313,0.198 10 false F16 6.042,3.281 6.375,3.458 0.333,0.177 10 false F131 5.823,1.104 6.135,1.302 0.313,0.198 10 false TC 5.552,1 5.865,1.198 0.313,0.198 10 false 19 1.563,1.01 1.875,1.208 0.313,0.198 10 false 13 1.615,2.115 1.927,2.313 0.313,0.198 10 false 4 6.042,3.438 6.531,3.635 0.49,0.198 10 false ECM 1.26,2.219 1.573,2.417 0.313,0.198 10 false CG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - ECM)
a.

Disconnect the F131 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F131-19 (TC) - F16-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)
a.
E265513C20
1.5,0.417 1.854,0.635 0.354,0.219 0.917,0.479 1.583,1.063 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.563,0.438 2.021,0.635 0.458,0.198 10 false F16 0.688,0.396 1,0.594 0.313,0.198 10 false CG
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F16-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)
a.
E265513C21
1.5,0.417 1.885,0.646 0.385,0.229 2.406,1.958 1.771,1.625 true 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 1.573,0.448 2.031,0.646 0.458,0.198 10 false F16 2.458,1.885 2.771,2.083 0.313,0.198 10 false TC
*a DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
F16-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU