Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › 2016.04–2016.10
RM30M0E _55 Steering _017104 STEERING COLUMN _0090111 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the engine switch is turned on (IG) while shaking the steering wheel, in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
·

All items

Click here(Click here)


-

WIRING DIAGRAM

E292927E02
1.49,1.302 1.948,1.5 0.458,0.198 10 false LIN 1.385,1.813 2,2.01 0.615,0.198 10 false SLR+ 1.458,2.365 1.917,2.563 0.458,0.198 10 false SLP 1.615,2.875 1.771,3.073 0.156,0.198 10 false E 0.646,3.5 1.104,3.698 0.458,0.198 10 false F43 0.635,3.646 2.146,4.052 1.51,0.406 10 false Certification ECU (Smart Key ECU Assembly) 0.771,4.448 2.406,4.708 1.635,0.26 10 false : LIN Communication Line 2.573,0.469 3.417,0.708 0.844,0.24 10 false from Battery 4.24,0.656 5.083,0.896 0.844,0.24 10 false STRG LOCK 5.24,0.396 5.396,0.594 0.156,0.198 10 false 7 5.24,1.135 5.396,1.333 0.156,0.198 10 false 5 5.25,1.708 5.406,1.906 0.156,0.198 10 false 3 5.25,2.24 5.406,2.438 0.156,0.198 10 false 4 5.25,2.771 5.406,2.969 0.156,0.198 10 false 1 5.458,0.479 5.615,0.677 0.156,0.198 10 false B 5.438,1.271 5.719,1.458 0.281,0.188 10 false LIN 5.438,1.844 5.719,2.031 0.281,0.188 10 false IGE 5.438,2.344 5.927,2.594 0.49,0.25 10 false SLP1 5.438,2.875 5.927,3.125 0.49,0.25 10 false GND 4.958,3.552 5.417,3.75 0.458,0.198 10 false F15 4.948,3.708 6.729,4.177 1.781,0.469 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 1.844,1.135 2,1.333 0.156,0.198 10 false 5 1.833,1.729 2.125,1.906 0.292,0.177 10 false 17 1.844,2.24 2.771,2.563 0.927,0.323 10 false 22 1.823,2.792 2.75,3.115 0.927,0.323 10 false 10

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Perform either of the following operations to lock/unlock the steering:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.

·

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.

*: for Automatic Transaxle and CVT



·

The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, confirm that the problem does not recur.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).

·

When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. This function prevents the engine from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch.



PROCEDURE

1.CHECK DTC (ALL)
a.

Using the GTS, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART




Result:
Proceed to
OK
NG



OK

2.CHECK ENGINE SWITCH (SWITCH CONDITION)

NG

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK ENGINE SWITCH (SWITCH CONDITION)
a.

Check the power source mode change.

i.

When the key is inside the vehicle and the shift lever is in P*, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

*: for Automatic Transaxle and CVT


OK:

Off → On (ACC) → On (IG) → Off




Result:
Proceed to
OK
NG



OK

3.CHECK SMART WARNING LIGHT

NG

GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) (PROBLEM SYMPTOMS TABLE)

3.CHECK SMART WARNING LIGHT
a.

Turn the engine switch on (IG).


b.

Check that the smart warning light on the combination meter assembly is rapidly blinking green.


Result:
Result Proceed to
Smart warning light is blinking rapidly. A
Smart warning light is not blinking rapidly. B



A

4.CHECK STEERING UNLOCK CONDITION

B

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
4.CHECK STEERING UNLOCK CONDITION
a.

While turning the steering wheel left and right, press the engine switch.


b.

Check that the steering is unlocked.

OK:

The steering is unlocked.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK SYSTEM IS NORMAL)

NG

5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
5.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (L CODE CHECK)

NG

13.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
6.READ VALUE USING GTS (L CODE CHECK)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


HINT:
Reasons for verification failure:
·

The steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

11.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Disconnect the steering lock ECU (steering lock actuator assembly) connector.


b.
C157850C63
0.344,0.896 0.833,1.188 0.49,0.292 1.302,2.417 1.052,1.677 true 2.25,2.417 2.5,1.677 true 0.396,0.302 0.625,0.479 0.229,0.177 10 false *a 0.49,0.969 0.979,1.24 0.49,0.271 10 false F15 0.708,1.573 1.063,1.76 0.354,0.188 10 false GND 2.563,1.573 2.719,1.76 0.156,0.188 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.


Standard Voltage:
Tester Connection Condition Specified Condition
F15-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)
a.
C157850C64
0.344,0.917 0.74,1.229 0.396,0.313 1.281,2.417 1.031,1.729 true 0.375,0.302 0.823,0.604 0.448,0.302 10 false *a 0.438,0.99 0.854,1.354 0.417,0.365 10 false F15 0.698,1.625 1.052,1.813 0.354,0.188 10 false GND
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-1 (GND) - Body ground Always Below 1 Ω



b.

Reconnect the steering lock ECU (steering lock actuator assembly) connector.


c.

Move the shift lever to P* and turn the engine switch off.

*: for Automatic Transaxle and CVT



d.
C241547C44
0.25,0.667 0.594,0.948 0.344,0.281 0.354,2.896 1.729,3.063 1.375,0.167 2.313,2.958 2.719,3.073 0.406,0.115 1.563,4.031 2.521,4.198 0.958,0.167 2.302,1.104 2.823,1.917 true 1.573,2.896 2.896,2.625 2.896,2.625 2.635,2.958 true 2.115,4.198 2.115,4.458 true 1.854,1.104 1.083,1.917 true 0.385,0.115 0.708,0.344 0.323,0.229 10 false *a 2.927,2.521 3.104,2.708 0.177,0.188 10 false *b 2.042,4.469 2.344,4.667 0.302,0.198 10 false *c 0.313,0.729 0.625,0.896 0.313,0.167 10 false F15 0.938,1.948 1.458,2.208 0.521,0.26 10 false IGE 2.708,1.958 3.063,2.125 0.354,0.167 10 false GND 3.052,4.01 3.427,4.177 0.375,0.167 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b Steering lock motor not operating
*c Steering lock motor operating


Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Item Content
Tester Connection F15-3 (IGE) - F15-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Vehicle Condition Steering lock motor not operating → Operating → Not operating


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

·

To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.

·

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.


*: for Automatic Transaxle and CVT





Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-3 (IGE) - F43-17 (SLR+) Always Below 1 Ω
F15-3 (IGE) - Body ground Always 10 kΩ or higher
F43-17 (SLR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Reconnect the steering lock ECU (steering lock actuator assembly) connector.


b.
C157849C30
0.292,0.885 0.74,1.177 0.448,0.292 1.906,1.979 2.813,2.823 true 0.375,0.271 0.667,0.521 0.292,0.25 10 false *a 0.417,0.948 0.792,1.198 0.375,0.25 10 false F15 2.854,2.76 3.156,2.938 0.302,0.177 10 false IGE
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F15-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

11.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.READ VALUE USING GTS (L CODE CHECK)
12.READ VALUE USING GTS (L CODE CHECK)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present:
·

The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

OK is displayed on the GTS.


Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

13.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Measure the resistance and voltage according to the value(s) in the table below.


C157849C32
0.292,0.885 0.74,1.177 0.448,0.292 1.667,1.938 0.938,2.74 true 0.375,0.271 0.667,0.521 0.292,0.25 10 false *a 0.417,0.948 0.792,1.198 0.375,0.25 10 false F15 0.719,2.771 1.167,2.958 0.448,0.188 10 false SLP1
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Standard Voltage:
Tester Connection Condition Specified Condition
F15-4 (SLP1) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



OK

14.CHECK STEERING UNLOCK CONDITION

NG

18.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
14.CHECK STEERING UNLOCK CONDITION
a.

While turning the steering wheel left and right, press the engine switch.


b.

Check that the steering is unlocked.

OK:

The steering is unlocked.



Result:
Proceed to
OK
NG



OK

END (CONNECT CONNECTORS PROPERLY)

NG

15.READ VALUE USING GTS (STEERING LOCK, STEERING UNLOCK)
15.READ VALUE USING GTS (STEERING LOCK, STEERING UNLOCK)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.


Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Lock State of whether steering lock ECU
(steering lock actuator assembly)
has determined steering is locked
Set or Unset Set: Steering locked
Unset: Steering unlocked
If this item displays "Unset", the steering does not lock.
Steering Unlock State of whether steering lock ECU
(steering lock actuator assembly)
determined steering is unlocked
Set or Unset Set: Steering unlocked
Unset: Steering locked
If this item displays "Unset", the steering does not unlock (engine cannot be started).
OK:

"Steering Lock" is "Unset" and "Steering Unlock" is "Set"


Result:
Proceed to
OK
NG



OK

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

16.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



b.

Perform registration.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

17.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
17.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

18.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F15 steering lock ECU (steering lock actuator assembly) connector.


b.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


c.

Check for deformation and corrosion of the connector case and terminals.

OK:

There is no deformation or corrosion of the connector case or terminals.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-4 (SLP1) - F43-22 (SLP) Always Below 1 Ω
F15-4 (SLP1) - Body ground Always 10 kΩ or higher
F43-22 (SLP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

20.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
20.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Entry&Start / Data List.


f.

According to the display on the GTS, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
HINT:
·

The reception state is maintained for 10 seconds.

·

When 10 seconds or more have elapsed after receiving the signal, the item changes to "NG".



OK or NG OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
·

If the unlock signal has not been received, the engine cannot be started.

·

If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.


Body Electrical > Entry&Start > Data List
Tester Display
Unlock Request Receive
50003 125 67
OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)