Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.04–2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  



FUNCTION OF SRS WARNING LIGHT


a.

Primary check

i.

Turn the ignition switch off. Wait for at least 2 seconds, then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and the diagnosis of the airbag system (including the seat belt pretensioners) is performed.

HINT:

If malfunctions are detected during the primary check, the SRS warning light remains on even after the primary check period of approximately 6 seconds.




b.

Constant check

i.

After the primary check, the airbag ECU assembly constantly monitors the airbag system for malfunctions.

HINT:

If malfunctions are detected during the constant check, the airbag ECU assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period of approximately 6 seconds after the ignition switch is turned to ON.


ii.

When the airbag system is malfunctioning:

·

The SRS warning light remains on even after the primary check period.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the ignition switch from off to ON.


HINT:

The airbag ECU assembly functions to keep the SRS warning light on if the airbag has been deployed.





SRS WARNING LIGHT CHECK


a.
C129423

Turn the ignition switch to ON, and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to ON (constant check).

HINT:

When any of the following symptoms occur, refer to Problem Symptoms Table.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE

·

The SRS warning light comes on occasionally after the primary check period.

·

The SRS warning light comes on, but a DTC is not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.





FUNCTION OF SRS CONNECTORS


a.

The SRS connectors are located as shown in the illustration (w/o VSC)

C281418C01
4.948,0.552 6.479,1.052 1.531,0.5 10 false Airbag ECU Assembly 1.01,1.365 2.365,1.552 1.354,0.188 10 false Front Airbag Sensor 0.333,2.188 3.052,2.385 2.719,0.198 10 false Horn Button Assembly (Driver Side Squib) 0.51,3.844 2.896,4.219 2.385,0.375 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH)*1 0.542,4.667 2.813,5.052 2.271,0.385 10 false Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 5.104,1.146 5.26,1.344 0.156,0.198 10 false 1 5.115,1.438 5.271,1.635 0.156,0.198 10 false 2 6.083,1.146 6.24,1.344 0.156,0.198 10 false 3 6.083,1.438 6.24,1.635 0.156,0.198 10 false 4 3.104,1.229 3.26,1.427 0.156,0.198 10 false 5 3.24,1.938 3.396,2.135 0.156,0.198 10 false 6 3.854,1.51 4.01,1.708 0.156,0.198 10 false 7 4.177,1.51 4.333,1.708 0.156,0.198 10 false 8 3.104,2.052 3.26,2.25 0.156,0.198 10 false 9 3.208,2.771 3.521,2.969 0.313,0.198 10 false 10 4.698,2.073 5.01,2.271 0.313,0.198 10 false 11 4.844,2.75 5.156,2.948 0.313,0.198 10 false 12 3.063,2.885 3.375,3.083 0.313,0.198 10 false 13 3.208,3.604 3.521,3.802 0.313,0.198 10 false 14 3.792,3.177 4.104,3.375 0.313,0.198 10 false 15 4.167,3.167 4.479,3.365 0.313,0.198 10 false 16 3.063,3.719 3.375,3.917 0.313,0.198 10 false 17 3.208,4.427 3.521,4.625 0.313,0.198 10 false 18 3.063,4.542 3.375,4.74 0.313,0.198 10 false 19 3.219,5.26 3.531,5.458 0.313,0.198 10 false 20 3.719,2.188 4.667,2.615 0.948,0.427 10 false Spiral Cable Sub-Assembly 0.198,2.99 3,3.427 2.802,0.438 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib)*1 5.625,1.292 5.781,1.49 0.156,0.198 10 false A 4.917,5.323 6.844,5.583 1.927,0.26 10 false *1: w/ Front Passenger Airbag

Connector Type Application
Terminal Twin-lock Mechanism Connectors 7, 8, 12, 15
Half Connection Prevention Mechanism Connectors 12, 16
Activation Prevention Mechanism Connectors 2, 4, 5, 7, 9, 11, 13, 17, 19
Connector Lock Mechanism (1) Connectors 10, 14, 18, 20
Connector Position Assurance Mechanism Connectors 6
Connector Lock Mechanism (2) Connector A
Improper Connection Prevention Lock Mechanism Connector A


b.

The SRS connectors are located as shown in the illustration (w/ VSC)

C352073E01
4.917,0.417 6.5,0.667 1.583,0.25 10 false Airbag ECU Assembly 0.792,1.385 2.417,1.583 1.625,0.198 10 false Front Airbag Sensor 0.75,2.198 2.167,2.583 1.417,0.385 10 false Horn Button Assembly (Driver Side Squib) 0.333,3 2.531,3.604 2.198,0.604 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 0.333,3.896 2.531,4.333 2.198,0.438 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 0.333,4.688 2.615,5.167 2.281,0.479 10 false Front Seat Outer Belt Assembly LH ( Front Pretensioner Squib LH) 3.375,2.24 4.375,2.656 1,0.417 10 false Spiral Cable Sub-Assembly 4.708,1.104 4.865,1.302 0.156,0.198 10 false 1 4.729,1.427 4.885,1.625 0.156,0.198 10 false 2 5.719,1.104 5.875,1.302 0.156,0.198 10 false 3 5.719,1.438 5.875,1.635 0.156,0.198 10 false 4 5.708,1.281 5.865,1.479 0.156,0.198 10 false A 6.583,1.104 6.74,1.302 0.156,0.198 10 false 3 6.615,1.427 6.771,1.625 0.156,0.198 10 false 4 2.708,1.198 2.865,1.396 0.156,0.198 10 false 5 2.865,1.948 3.021,2.146 0.156,0.198 10 false 6 2.719,2.052 2.875,2.25 0.156,0.198 10 false 9 2.823,2.781 3.135,2.979 0.313,0.198 10 false 10 2.677,2.885 2.99,3.083 0.313,0.198 10 false 13 2.844,3.625 3.156,3.823 0.313,0.198 10 false 14 2.708,3.708 3.021,3.906 0.313,0.198 10 false 17 2.854,4.438 3.167,4.635 0.313,0.198 10 false 18 2.698,4.531 3.01,4.729 0.313,0.198 10 false 19 2.854,5.281 3.167,5.479 0.313,0.198 10 false 20 3.771,3.167 4.083,3.365 0.313,0.198 10 false 15 4.177,3.167 4.49,3.365 0.313,0.198 10 false 16 4.521,2.781 4.833,2.979 0.313,0.198 10 false 12 4.385,2.063 4.698,2.26 0.313,0.198 10 false 11 3.604,1.49 3.76,1.688 0.156,0.198 10 false 7 3.917,1.49 4.073,1.688 0.156,0.198 10 false 8

Connector Type Application
Terminal Twin-lock Mechanism Connectors 7, 8, 12, 15
Half Connection Prevention Mechanism Connectors 12, 16
Activation Prevention Mechanism Connectors 2, 4, 5, 7, 9, 11, 13, 17, 19
Connector Lock Mechanism (1) Connectors 10, 14, 18, 20
Connector Position Assurance Mechanism Connectors 6
Connector Lock Mechanism (2) Connector A
Improper Connection Prevention Lock Mechanism Connector A


c.

Half connection prevention mechanism

C147461C02
1.542,1.417 1.406,1.125 1.406,1.125 1.281,1.125 false 1.823,1.365 1.625,0.833 1.625,0.833 1.49,0.833 false 2.375,1.302 2.042,0.552 2.042,0.552 1.917,0.552 true 2.99,1.177 3.292,0.583 3.292,0.583 3.406,0.583 false 3.24,1.302 3.5,0.896 3.5,0.896 3.615,0.896 true 6.021,1.156 5.75,0.833 5.75,0.833 5.635,0.833 true 1.125,0.458 2.021,0.688 0.896,0.229 10 false Locking Arm 0.979,0.729 1.583,0.948 0.604,0.219 10 false Stopper 0.469,1 1.375,1.229 0.906,0.229 10 false Locking Part 3.448,0.5 3.969,0.729 0.521,0.229 10 false Slider 3.667,0.802 4.188,1.052 0.521,0.25 10 false Spring 5.156,0.74 5.823,0.99 0.667,0.25 10 false Stopper 4.708,1.917 6.156,2.188 1.448,0.271 10 false Rebounded by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected due to the spring force so that no continuity exists.



d.

Activation prevention mechanism

C238382E11
1.583,1.063 1.198,0.917 false 5.26,1.521 5.26,2.042 false 1.844,1.667 1.844,2.083 false 1.656,1.448 1.198,1.448 false 2.646,1.646 2.969,1.646 false 2.354,1.385 3,0.969 3,0.969 2.552,1.458 false 1.771,0.375 2.51,0.708 0.74,0.333 10 When open 0.313,0.833 1.208,1.146 0.896,0.313 10 Male Housing 3.042,0.885 4.115,1.229 1.073,0.344 10 Female Terminal 0.302,1.375 1.198,1.698 0.896,0.323 10 Male Terminal 3.01,1.573 4.073,1.938 1.063,0.365 10 Female Housing 1.26,2.104 2.448,2.448 1.188,0.344 10 Short Spring Plate 5.448,0.375 6.354,0.75 0.906,0.375 10 When shorted 4.375,2.063 6.156,2.635 1.781,0.573 10 Short spring plate contacting the male terminal

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive and negative terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E11
2.521,0.323 2.021,0.198 false 2.635,0.76 2.281,0.885 false 2.469,1.24 2.271,1.323 false 4.938,0.875 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 Groove 5.281,0.604 6.896,0.938 1.615,0.333 10 Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector lock button engages the locking button claw to the groove on the other side connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464C01
0.854,0.198 1.021,0.198 false 0.833,1.104 0.854,0.198 false 1.052,0.479 1.219,0.479 false 0.938,1.198 1.052,0.479 false 0.729,2.292 0.958,2.292 false 0.51,1.802 0.729,2.292 false 5.625,0.781 5.469,0.781 false 5.656,1.094 5.625,0.781 false 1.063,0.125 2.344,0.354 1.281,0.229 10 Female Connector 1.26,0.406 2.198,0.635 0.938,0.229 10 Locking Part 1,2.229 2.167,2.51 1.167,0.281 10 Male Connector 2.958,0.302 4.656,0.552 1.698,0.25 10 Primary Lock Completed 5.073,0.302 6.885,0.563 1.813,0.26 10 Secondary Lock Completed 4.896,0.698 5.521,0.948 0.625,0.25 10 Retainer

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side and secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, they are completely engaged.



g.

Connector lock mechanism (2) (w/o VSC)

E263577C01
0.573,2.094 0.698,2.094 0.698,2.094 1.083,1.458 true 1.719,3.198 2.375,3.625 2.375,3.625 2.531,3.625 true 3.75,3.344 3.906,3.344 3.906,3.344 4.073,2.813 false 4.76,3.521 4.917,3.521 4.917,3.521 5.552,3.313 true 4.323,1.396 4.688,1.854 4.688,1.854 4.823,1.854 false 5.479,2.573 5.594,2.573 5.594,2.573 5.813,2.802 false 5.906,2.677 6,2.281 6,2.281 6.115,2.281 false 0.167,2.01 0.938,2.208 0.771,0.198 10 false Lance 2.594,3.552 3.823,3.75 1.229,0.198 10 false Retainer 3.219,3.24 4.448,3.438 1.229,0.198 10 false Retainer 4.208,3.427 5.438,3.625 1.229,0.198 10 false Retainer 4.865,1.771 5.781,1.969 0.917,0.198 10 false Holder 5.063,2.49 5.979,2.688 0.917,0.198 10 false Holder 6.146,2.198 6.76,2.396 0.615,0.198 10 false Claw


h.

Connector lock mechanism (2) (w/ VSC)

C262358E01
0.667,1.917 0.917,1.917 0.917,1.917 1.167,1.5 false 2.75,3.583 2.333,3.583 2.333,3.583 1.833,3.167 false 4.25,2.833 4.083,3.25 4.083,3.25 3.833,3.25 false 5.594,3.344 4.833,3.5 4.833,3.5 4.667,3.5 false 5.802,2.833 5.667,2.583 5.667,2.583 5.5,2.583 false 5.885,2.729 6,2.417 6,2.417 6.083,2.417 false 4.417,1.5 4.583,1.833 4.583,1.833 4.75,1.833 false 0.26,1.833 0.677,2.031 0.417,0.198 10 Lance 2.802,3.51 3.385,3.677 0.583,0.167 10 Retainer 3.292,3.156 3.875,3.323 0.583,0.167 10 Retainer 4.135,3.406 4.719,3.573 0.583,0.167 10 Retainer 4.792,1.75 5.375,1.917 0.583,0.167 10 Holder 5.083,2.5 5.667,2.667 0.583,0.167 10 Holder 6.125,2.333 6.458,2.5 0.333,0.167 10 Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer to the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



i.

Improper connection prevention lock mechanism (w/o VSC)

E263578E01
5.5,0.667 5.5,0.25 5.5,0.25 5.667,0.25 true 1.167,1.583 1.167,2.417 1.167,2.417 1,2.417 true 5.5,1.083 5.25,1.583 5.25,1.583 5,1.583 true 1.083,1.167 1.083,0.583 1.083,0.583 1.25,0.583 true 5,3 4.5,3 true 1.302,0.49 1.458,0.688 0.156,0.198 10 false A 0.521,2.323 1.021,2.521 0.5,0.198 10 false Unlock Rib 4.25,1.5 5,1.917 0.75,0.417 10 false Temporarily Hold Lock 4.333,0.083 5.073,0.281 0.74,0.198 10 false Top View 5.708,0.177 6.458,0.427 0.75,0.25 10 false Unlock Rib 4.104,2.906 4.5,3.125 0.396,0.219 10 false Lever


j.

Improper connection prevention lock mechanism (w/ VSC)

C265081E01
5.292,0.792 5.292,0.219 5.292,0.219 5.656,0.219 false 5.302,1.146 5.302,1.854 5.302,1.854 4.615,1.854 true 4.958,2.979 4.573,2.979 true 1.24,0.99 1.24,0.323 1.24,0.323 1.552,0.323 true 5.99,0.719 5.99,1.031 5.99,1.031 5.51,1.031 true 1.229,1.354 1.229,2.531 1.229,2.531 0.958,2.531 true 3.948,0.073 4.594,0.344 0.646,0.271 10 Top View 0.271,2.448 1.021,2.74 0.75,0.292 10 Unlock Rib 3.938,1.76 4.625,2.292 0.688,0.531 10 Temporary Hold Lock 4.229,2.896 4.656,3.146 0.427,0.25 10 Lever 5.698,0.146 6.521,0.385 0.823,0.24 10 Unlock Rib 1.594,0.25 1.854,0.5 0.26,0.25 10 A 5.948,0.552 6.146,0.729 0.198,0.177 10 A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag ECU assembly, the unlock rib unlocks the temporarily hold lock, allowing the lever to be pushed in by rotating around the A axis.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the airbag ECU assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm (0.0197 in.)) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C281393E09
1.708,1.625 2.25,2.542 2.25,2.542 2.76,1.625 true 1.698,1.927 2.24,2.552 2.24,2.552 2.75,1.927 true 1.958,1.604 2.25,2.542 2.25,2.542 2.49,1.615 true 2.219,1.615 2.25,2.531 true 4.823,1.635 5.031,2.552 5.031,2.552 5.219,1.635 true 4.823,1.948 5.031,2.573 5.031,2.573 5.219,1.948 true 5.167,3.583 4.875,4.542 4.875,4.542 5.219,3.917 true 2.521,3.583 2.229,4.542 2.229,4.542 2.573,3.917 true 3.177,3.438 3.333,3.188 3.333,3.188 3.635,3.188 false 3.229,3.802 3.563,3.188 false 5.719,3.438 5.875,3.188 5.875,3.188 6.177,3.188 false 5.688,3.781 6.021,3.198 false 1.479,5.938 1.677,6.531 1.677,6.531 1.844,5.938 true 1.573,5.927 1.677,6.531 1.677,6.531 1.729,5.927 true 3.333,8.177 3.333,7.844 true 4.156,5.802 4.313,5.552 4.313,5.552 4.49,5.552 false 6.375,5.802 6.531,5.552 6.531,5.552 6.667,5.552 false 6.542,7.74 6.542,7.365 6.542,7.365 6.688,7.365 false 5.906,8.188 5.906,7.854 true 0.875,7.833 1.146,8.146 1.146,8.146 1.354,7.854 true 1.031,7.844 1.146,8.135 1.146,8.135 1.198,7.844 true 3.458,6.573 3.458,5.74 true 5.615,6.583 5.615,5.75 true 4,7.74 4.156,7.49 4.156,7.49 4.333,7.49 false 2.198,0.302 4.979,0.552 2.781,0.25 10 false Airbag ECU Assembly Connector: 1.875,2.542 2.802,2.802 0.927,0.26 10 false Short Spring 4.708,2.573 5.635,2.833 0.927,0.26 10 false Short Spring 1.865,4.542 2.792,4.802 0.927,0.26 10 false Short Spring 4.573,4.552 5.5,4.813 0.927,0.26 10 false Short Spring 1.344,6.531 2.271,6.792 0.927,0.26 10 false Short Spring 3.104,6.563 4.031,6.823 0.927,0.26 10 false Short Spring 5.281,6.563 6.208,6.823 0.927,0.26 10 false Short Spring 0.813,8.167 1.74,8.427 0.927,0.26 10 false Short Spring 3.052,8.219 3.979,8.479 0.927,0.26 10 false Short Spring 5.552,8.198 6.479,8.458 0.927,0.26 10 false Short Spring 1.885,2.865 2.844,3.135 0.958,0.271 10 false Before Release 3.094,5.198 4.063,5.458 0.969,0.26 10 false Before Release 2.854,7.094 3.854,7.354 1,0.26 10 false Before Release 4.531,2.917 5.448,3.188 0.917,0.271 10 false After Release 5.281,5.188 6.198,5.458 0.917,0.271 10 false After Release 5.385,7.104 6.302,7.375 0.917,0.271 10 false After Release 0.292,4.896 1.99,5.323 1.698,0.427 10 false Spiral Cable Sub-assembly Connector: 0.167,6.938 2.698,7.198 2.531,0.26 10 false No. 2 Instrument Panel Wire Connector: 4.354,7.385 4.802,7.604 0.448,0.219 10 false Paper 6.708,7.271 7.156,7.49 0.448,0.219 10 false Paper 6.708,5.458 7.156,5.677 0.448,0.219 10 false Paper 3.667,3.094 4.115,3.313 0.448,0.219 10 false Paper 4.531,5.479 4.979,5.698 0.448,0.219 10 false Paper 6.229,3.104 6.677,3.323 0.448,0.219 10 false Paper 0.167,0.167 1.635,0.406 1.469,0.24 12 false w/o VSC:

C352079E04
2.427,1.49 2,2.177 2,2.177 1.5,1.51 true 2,2.167 1.958,1.5 true 1.74,1.5 2,2.167 2,2.167 2.208,1.49 true 3.917,1.5 4.083,2.167 4.083,2.167 4.25,1.5 true 5.896,1.813 5.74,2.208 5.74,2.208 5.563,1.823 true 5.167,3.583 4.75,4.417 4.75,4.417 5.167,3.917 true 5.688,3.438 6,3.083 6,3.083 6.333,3.083 false 2.5,3.583 2.083,4.417 2.083,4.417 2.5,3.917 true 5.563,1.531 5.74,2.188 5.74,2.188 5.896,1.531 true 3.917,1.833 4.083,2.167 4.083,2.167 4.25,1.833 true 5.667,3.792 6.167,3.083 false 4.167,5.792 4.333,5.5 4.333,5.5 4.5,5.5 false 3.167,3.448 3.5,3.083 3.5,3.083 3.75,3.083 true 3.156,3.792 3.667,3.083 false 4.333,7.333 4.167,7.333 4.167,7.333 4,7.729 false 6.688,7.25 6.521,7.25 6.521,7.25 6.5,7.75 false 3.417,6.5 3.417,5.75 true 5.625,6.5 5.625,5.75 true 6.333,5.792 6.5,5.5 6.5,5.5 6.667,5.5 false 1.438,5.938 1.667,6.5 1.667,6.5 1.865,5.938 true 5.917,8.167 5.917,7.833 true 3.333,8.167 3.333,7.833 true 0.917,7.833 1.083,8.167 1.083,8.167 1.333,7.833 true 1,7.833 1.083,8.167 1.083,8.167 1.25,7.833 true 2.427,1.781 2,2.198 2,2.198 1.5,1.771 true 1.563,5.948 1.667,6.469 1.667,6.469 1.75,5.948 true 1.646,2.26 3.479,2.458 1.833,0.198 10 false Short Spring 1.667,2.885 3.813,3.083 2.146,0.198 10 false Before Release 5.396,2.281 6.885,2.563 1.49,0.281 10 false Short Spring 3.792,2.25 4.958,2.531 1.167,0.281 10 false Short Spring 6.396,2.979 6.813,3.229 0.417,0.25 10 false Paper 4.406,4.448 6.24,4.646 1.833,0.198 10 false Short Spring 1.708,4.458 3.542,4.656 1.833,0.198 10 false Short Spring 5.25,5.25 6.5,5.5 1.25,0.25 10 false After Release 3.094,5.25 4.167,5.625 1.073,0.375 10 false Before Release 0.417,4.75 2.167,5.167 1.75,0.417 10 false Spiral Cable Sub-assembly Connector: 6.729,5.417 7.156,5.667 0.427,0.25 10 false Paper 6.74,7.167 7.146,7.458 0.406,0.292 10 false Paper 2.979,8.188 4.813,8.385 1.833,0.198 10 false Short Spring 5.573,8.198 6.667,8.448 1.094,0.25 10 false Short Spring 0.771,8.219 2.604,8.417 1.833,0.198 10 false Short Spring 1.25,6.583 3.083,6.781 1.833,0.198 10 false Short Spring 3.073,6.51 4.906,6.708 1.833,0.198 10 false Short Spring 5.271,6.531 7.104,6.729 1.833,0.198 10 false Short Spring 4.396,7.229 4.979,7.427 0.583,0.198 10 false Paper 4.563,5.396 5.333,5.594 0.771,0.198 10 false Paper 0.083,7 2.583,7.25 2.5,0.25 10 false No. 2 Instrument Panel Wire Connector: 2.75,7.052 3.833,7.25 1.083,0.198 10 false Before Release 5.333,7.125 6.417,7.406 1.083,0.281 10 false Before Release 4.5,2.917 5.75,3.167 1.25,0.25 10 false After Release 3.813,2.979 4.229,3.229 0.417,0.25 10 false Paper 2.208,0.302 4.719,0.594 2.51,0.292 10 false Airbag ECU Assembly Connector: 0.167,0.167 1.458,0.406 1.292,0.24 12 false w/ VSC: