Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.04
RM30M0E _51 Engine / Hybrid System _053304 2NR-FE ENGINE CONTROL _0258353 SFI SYSTEM U

2NR-FE ENGINE CONTROL  SFI SYSTEM  FAIL-SAFE CHART  


If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.

DTC Code Component Fail-Safe Operation Fail-Safe Deactivation Condition
C1476
C1477
C1478
Brake Booster Pressure Sensor The frequency that the air conditioning system is turned off is increased*1. Pass condition detected
C147A
C147B
Atmospheric Pressure Sensor The frequency that the air conditioning system is turned off is increased*1. Pass condition detected
P0011
P0015
VVT system
·

Idle up (control of combustion worsening).

·

Fuel-cut control is stopped.

·

Engine speed is limited.


Pass condition detected
P0031
P0032
P101D
Air fuel ratio sensor heater The ECM turns off the air fuel ratio sensor heater. Ignition switch off
P0037
P0038
P102D
Heated oxygen sensor heater The ECM turns off the heated oxygen sensor heater. Ignition switch off
P0102
P0103
Mass air flow meter The ECM performs fuel cut on all cylinders when the engine speed 3000 rpm or higher. Pass condition detected
P0112
P0113
Intake air temperature sensor The ECM estimates the intake air temperature to be 20°C (68°F). Pass condition detected
P0115
P0117
P0118
Engine coolant temperature sensor The ECM estimates the engine coolant temperature to be 80°C (176°F). Pass condition detected
P0120
P2121
P0122
P0123
P0220
P0222
P0223
P0604
P0606
P060A
P060B
P060D
P060E
P0657
P2102
P2103
P2111
P2112
P2118
P2119
P2135
Electronic throttle control system The ECM cuts off throttle actuator current and the throttle valve is returned to a 5.5° throttle position by the return spring.
The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to continue at minimal speed*2.
Pass condition detected and then ignition switch turned off
P0300
P0301
P0302
P0303
P0304
*3
·

Fuel injector assembly

·

Electronic throttle control system


When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.

Under a low load and at a low engine speed:

- Fuel cut is performed on the malfunctioning cylinder.

2.

Under a high load and at a high engine speed:

- Throttle valve opening angle control is performed.

- Fuel cut is performed on all cylinders or the malfunctioning cylinder.


Pass condition detected and then ignition switch turned off
P0327
P0328
Knock sensor The ECM sets the ignition timing to maximum retard. Ignition switch off
P0335
P0337
P0338
Crankshaft Position Sensor
·

The ECM limits the engine speed.

·

The ECM sets ignition timing to maximum retard.


Pass condition detected and then ignition switch turned off
P0504 Stop light switch assembly The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction. Pass condition detected and then ignition switch turned off
P0560 System Voltage The alternator command is fixed. Pass condition detected and then ignition switch turned off
P2120
P2121
P2122
P2123
P2125
P2127
P2128
P2138
Accelerator pedal position sensor The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.
If there is a malfunction in either circuit, the ECM limits the engine output.
If there is a malfunction in both circuits, the ECM regards the accelerator pedal as being released.
As a result, the throttle valve is closed and the engine idles.
Pass condition detected and then ignition switch turned off
P2237
P2238
P2239
P2252
P2253
Air fuel ratio sensor
·

Air fuel ratio feedback control is stopped.

·

Current to the air fuel ratio sensor heater is cut.


Pass condition detected and then ignition switch turned off

HINT:
·

*1: w/ Air Conditioning System

·

*2: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.

·

*3: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.