If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.
| DTC Code | Component | Fail-Safe Operation | Fail-Safe Deactivation Condition |
|---|---|---|---|
| C1476
C1477 C1478 |
Brake Booster Pressure Sensor | The frequency that the air conditioning system is turned off is increased*1. | Pass condition detected |
| C147A
C147B |
Atmospheric Pressure Sensor (vacuum sensor assembly) | The frequency that the air conditioning system is turned off is increased*1. | Pass condition detected |
| P0011
P0015 |
VVT system | ·
Idle up (control of combustion worsening). ·
Fuel-cut control is stopped. ·
Engine speed is limited. |
Pass condition detected |
| P0031
P0032 P101D |
Air fuel ratio sensor heater | The ECM turns off the air fuel ratio sensor heater. | Ignition switch off |
| P0037
P0038 P102D |
Heated oxygen sensor heater | The ECM turns off the heated oxygen sensor heater. | Ignition switch off |
| P0102
P0103 |
Mass air flow meter | The ECM performs fuel cut on all cylinders when the engine speed 3000 rpm or higher. | Pass condition detected |
| P0112
P0113 |
Intake air temperature sensor | The ECM estimates the intake air temperature to be 20°C (68°F). | Pass condition detected |
| P0115
P0117 P0118 |
Engine coolant temperature sensor | The ECM estimates the engine coolant temperature to be 80°C (176°F). | Pass condition detected |
| P0120
P2121 P0122 P0123 P0220 P0222 P0223 P0604 P0606 P060A P060B P060D P060E P0657 P2102 P2103 P2111 P2112 P2118 P2119 P2135 |
Electronic throttle control system | The ECM cuts off throttle actuator current and the throttle valve is returned to a 5.5° throttle position by the return spring.
The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to continue at minimal speed*2. |
Pass condition detected and then ignition switch turned off |
| P0300
P0301 P0302 P0303 P0304 *3 |
·
Fuel injector assembly ·
Electronic throttle control system |
When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.
Under a low load and at a low engine speed: - Fuel cut is performed on the malfunctioning cylinder. 2.
Under a high load and at a high engine speed: - Throttle valve opening angle control is performed. - Fuel cut is performed on all cylinders or the malfunctioning cylinder. |
Pass condition detected and then ignition switch turned off |
| P0327
P0328 |
Knock sensor | The ECM sets the ignition timing to maximum retard. | Ignition switch off |
| P0335
P0337 P0338 |
Crankshaft Position Sensor | ·
The ECM limits the engine speed. ·
The ECM sets ignition timing to maximum retard. |
Pass condition detected and then ignition switch turned off |
| P0504 | Stop light switch assembly | The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction. | Pass condition detected and then ignition switch turned off |
| P0560 | System Voltage | The alternator command is fixed. | Pass condition detected and then ignition switch turned off |
| P2120
P2121 P2122 P2123 P2125 P2127 P2128 P2138 |
Accelerator pedal position sensor | The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.
If there is a malfunction in either circuit, the ECM limits the engine output. If there is a malfunction in both circuits, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. |
Pass condition detected and then ignition switch turned off |
| P2237
P2238 P2239 P2252 P2253 |
Air fuel ratio sensor | ·
Air fuel ratio feedback control is stopped. ·
Current to the air fuel ratio sensor heater is cut. |
Pass condition detected and then ignition switch turned off |
*1: w/ Air conditioning system
*2: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
*3: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.