In this circuit, the meter CPU receives engine coolant temperature signals from the ECM using the CAN communication system (CAN V Bus). The meter CPU displays engine coolant temperature that is calculated based on the data received from the ECM.
If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores DTCs. Troubleshoot the SFI system.
for 1NZ-FE with Automatic Transaxle
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for 1NZ-FE with Manual Transaxle
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
for 2NZ-FE with Automatic Transaxle
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for 2NZ-FE with Manual Transaxle
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
w/ Air Fuel Ratio Sensor
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DTC CHECK / CLEAR
for 1NR-FE
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
for 2NR-FE
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are not output. | A |
| CAN communication DTCs are output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Lamp Coolant Cool | Water temperature cool indicator light | OFF or ON | - |
| Indicat. Lamp Coolant Hot | Water temperature hot warning light | OFF or ON | - |
| Tester Display |
|---|
| Indicat. Lamp Coolant Cool |
| Tester Display |
|---|
| Indicat. Lamp Coolant Hot |
Value selected during Active Test is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Coolant Temperature | Engine coolant temperature | Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) | 75 to 100°C (167 to 212°F): After warming up | - |
| Tester Display |
|---|
| Coolant Temperature |
Vehicle's coolant temperature and tester value are the same.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if SFI system DTCs are output.
for 1NZ-FE with Automatic Transaxle
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for 1NZ-FE with Manual Transaxle
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
for 2NZ-FE with Automatic Transaxle
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for 2NZ-FE with Manual Transaxle
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
w/ Air Fuel Ratio Sensor
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DTC CHECK / CLEAR
for 1NR-FE
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
for 2NR-FE
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| SFI system DTCs are not output. | A |
| SFI system DTCs are output. (for 1NZ-FE with Automatic Transaxle) | B |
| SFI system DTCs are output. (for 1NZ-FE with Manual Transaxle) | C |
| SFI system DTCs are output. (for 2NZ-FE with Automatic Transaxle) | D |
| SFI system DTCs are output. (for 2NZ-FE with Manual Transaxle) | E |
| SFI system DTCs are output. (w/ Air Fuel Ratio Sensor) | F |
| SFI system DTCs are output. (for 1NR-FE) | G |
| SFI system DTCs are output. (for 2NR-FE) | H |
A
B
C
D
E
F
G
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
H
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING