Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PRESSURE SENSOR(for 1NR-FE, 2NR-FE) › from 2016.04
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0259841 AIR CONDITIONING PRESSURE SENSOR(for 1NR-FE, 2NR-FE) G

HEATING / AIR CONDITIONING  AIR CONDITIONING PRESSURE SENSOR(for 1NR-FE, 2NR-FE)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 88719A 1.INSPECT AIR CONDITIONER PRESSURE SENSOR (for Automatic Air Conditioning System)

a.

Check the wire harness.

i.

Disconnect the A43 air conditioner pressure sensor connector.


ii.

Disconnect the F3 air conditioning amplifier assembly connector.


iii.
I109914C13
1.458,0.521 1.958,0.75 0.5,0.229 1.458,2.5 1.958,2.729 0.5,0.229 2.375,4.208 2.229,3.802 true 1.063,4.167 1.5,3.594 true 1.656,4.188 1.656,3.792 true 1.198,2.135 1.531,1.469 true 2.25,2.146 1.917,1.479 true 1.719,2.156 1.719,1.49 true 0.979,0.781 1.292,0.938 0.313,0.156 10 false *a 0.208,2.792 0.521,2.948 0.313,0.156 10 false *b 1.573,0.563 1.885,0.719 0.313,0.156 10 false A43 1.625,2.531 1.938,2.688 0.313,0.156 10 false F3 2.177,4.24 2.594,4.396 0.417,0.156 10 false SG-2 0.875,4.219 1.292,4.375 0.417,0.156 10 false PSW 1.51,4.229 1.927,4.385 0.417,0.156 10 false S5-3 1.104,2.104 1.417,2.26 0.313,0.156 10 false - 2.26,2.115 2.51,2.271 0.25,0.156 10 false + 1.635,2.188 2.052,2.438 0.417,0.25 10 false PR
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)
*b Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-1 (-) - F3-34 (SG-2) Always Below 1 Ω
A43-2 (PR) - F3-9 (PSW) Always Below 1 Ω
A43-3 (+) - F3-30 (S5-3) Always Below 1 Ω
A43-1 (-) - Body ground Always 10 kΩ or higher
A43-2 (PR) - Body ground Always 10 kΩ or higher
A43-3 (+) - Body ground Always 10 kΩ or higher

If the result is not as specified, repair the wire harness.


iv.

Connect the F3 air conditioning amplifier assembly connector.


v.

Turn the ignition switch to ON.


vi.
E208778C09
1.469,0.333 1.969,0.583 0.5,0.25 2.281,1.646 1.917,1.229 true 0,0 0.313,0.156 0.313,0.156 10 false *a 1.604,0.385 2.063,0.583 0.458,0.198 10 false A43 2.292,1.646 2.448,1.844 0.156,0.198 10 false +
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)


Measure the voltage according to the value(s) in the table below.

Tester Connection Condition Specified Condition
A43-3 (+) - Body ground Ignition switch On 4.75 to 5.25 V
A43-3 (+) - Body ground Ignition switch Off Below 1 V

If the result is not as specified, replace the air conditioning amplifier assembly.



b.

Check the air conditioner pressure sensor.

i.

Install a manifold gauge set.


ii.

Connect the A43 air conditioner pressure sensor connector.


iii.

Start the engine.


iv.

Turn the A/C switch on.


v.
E182281C40
1.104,0.083 1.594,0.375 0.49,0.292 1.104,0.094 1.594,0.385 0.49,0.292 1.479,1.021 1.771,1.76 true 0.813,1.75 1.052,1.104 true 1.656,1.813 2.031,2 0.375,0.188 10 false PSW 1.271,0.156 1.573,0.333 0.302,0.177 10 false F3 0.104,0.01 0.323,0.188 0.219,0.177 10 false *a 0.646,1.792 1.021,1.979 0.375,0.188 10 false SG-2
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


Standard Voltage:
Tester Connection Condition Specified Condition
F3-9 (PSW) - F3-34 (SG-2) Refrigerant pressure: (less than 3025 kPa (30.8 kgf/cm2, 439 psi) and more than 176 kPa (1.8 kgf/cm2, 26 psi)) 0.74 to 4.62 V

If the result is not as specified, replace the air conditioner pressure sensor.



Hide 88719A 2.INSPECT AIR CONDITIONER PRESSURE SENSOR (for Manual Air Conditioning System)

a.

Check the wire harness.

i.

Disconnect the A43 air conditioner pressure sensor connector.


ii.

Disconnect the F124 air conditioning amplifier assembly connector.


iii.
I109914C14
1.458,2.5 1.958,2.75 0.5,0.25 1.448,0.479 1.948,0.729 0.5,0.25 1.25,2 1.5,1.469 true 2.167,2 1.917,1.479 true 2.75,4.25 2.396,3.594 true 1.052,4.208 1.5,3.604 true 1.656,4.208 1.656,3.781 true 1.708,2.073 1.708,1.49 true 2.615,4.271 3.094,4.438 0.479,0.167 10 false SG-2 0.167,2.833 0.479,3.031 0.313,0.198 10 false *b 1.573,2.542 2.094,2.802 0.521,0.26 10 false F124 1.573,0.521 1.885,0.719 0.313,0.198 10 false A43 1.177,1.969 1.49,2.167 0.313,0.198 10 false - 2.177,2.01 2.49,2.208 0.313,0.198 10 false + 0.875,4.25 1.354,4.417 0.479,0.167 10 false PSW 1.521,4.25 2,4.417 0.479,0.167 10 false S5-3 0.854,0.74 1.167,0.938 0.313,0.198 10 false *a 1.615,2.115 1.927,2.313 0.313,0.198 10 false PR
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)
*b Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-1 (-) - F124-15 (SG-2) Always Below 1 Ω
A43-2 (PR) - F124-9 (PSW) Always Below 1 Ω
A43-3 (+) - F124-30 (S5-3) Always Below 1 Ω
A43-1 (-) - Body ground Always 10 kΩ or higher
A43-2 (PR) - Body ground Always 10 kΩ or higher
A43-3 (+) - Body ground Always 10 kΩ or higher

If the result is not as specified, repair the wire harness.


iv.

Connect the F124 air conditioning amplifier assembly connector.


v.

Turn the ignition switch to ON.


vi.
E208778C10
1.5,0.219 1.906,0.49 0.406,0.271 2.281,1.646 1.917,1.229 true 0.208,0.125 0.521,0.281 0.313,0.156 10 false *a 1.594,0.271 2.052,0.469 0.458,0.198 10 false A43 2.292,1.646 2.448,1.844 0.156,0.198 10 false +
*a Front view of wire harness connector
(to Air Conditioner Pressure Sensor)


Measure the voltage according to the value(s) in the table below.

Tester Connection Condition Specified Condition
A43-3 (+) - Body ground Ignition switch On 4.75 to 5.25 V
A43-3 (+) - Body ground Ignition switch Off Below 1 V

If the result is not as specified, replace the air conditioning amplifier assembly.



b.

Check the air conditioner pressure sensor.

i.

Install a manifold gauge set.


ii.

Connect the A43 air conditioner pressure sensor connector.


iii.

Start the engine.


iv.

Turn the A/C switch on.


v.
E276833C14
1.01,0.167 1.417,0.396 0.406,0.229 2,1.75 1.479,1 true 0.625,1.781 0.99,1.021 true 1.073,0.188 1.531,0.385 0.458,0.198 10 false F124 1.958,1.802 2.417,2 0.458,0.198 10 false PSW 0.073,0.052 0.385,0.302 0.313,0.25 10 false *a 0.49,1.802 0.948,2 0.458,0.198 10 false SG-2
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


Standard Voltage:
Tester Connection Condition Specified Condition
F124-9 (PSW) - F124-15 (SG-2) Refrigerant pressure: (less than 3025 kPa (30.8 kgf/cm2, 439 psi) and more than 176 kPa (1.8 kgf/cm2, 26 psi)) 0.74 to 4.62 V

If the result is not as specified, replace the air conditioner pressure sensor.