Refer to Service Bulletin for the installation position of the transponder key ECU assembly.
80960
1.INSTALL POWER STEERING MOTOR ASSEMBLY
Do not drop the power steering motor assembly, strike it with tools or subject it to impacts.
If the power steering motor assembly is subjected to an impact, replace it with a new one.
Do not pull the wire harness of the power steering motor assembly.
Do not allow any moisture to come into contact with the power steering motor assembly.
Do not allow any foreign objects to contaminate the steering column assembly and the power steering motor assembly.
|
Grease |
Apply the grease that is supplied with a new steering column assembly or power steering motor assembly to the serrated part of the steering column assembly.
Be sure to use the supplied grease only.
Temporarily install the power steering motor assembly to the steering column assembly with the 2 bolts.
When temporarily installing the 2 bolts to the power steering motor assembly, do not tighten them all the way down.
| *a | Wooden Block |
Secure the steering column assembly in a vise using aluminum plates and wooden blocks.
Do not overtighten the vise.
Using SST, turn the steering main shaft once 180 degrees to the left and then 180 degrees to the right at a speed of 60 rpm, and repeat 2 to 3 times to adjust the axis centering of the power steering motor assembly.
Tighten the 2 bolts.
Using SST, measure the turning torque of the steering main shaft.
1.42 N*m (14 kgf*cm, 13 in.*lbf) or less
Ensure that there is no abnormal resistance during rotation.
If the turning torque is not as specified, readjust the axis centering of the power steering motor assembly.
for 1NR-FE, 2NR-FE:
for LHD:
Install 3 new wire harness clamps to the wire harness as shown in the illustration.
| *1 | Torque Sensor Wire Harness | *2 | Power Steering Motor Wire Harness |
| *3 | Wire Harness Clamp | - | - |
| *a | 270 to 290 mm (10.6 to 11.4 in.) | *b | 150 to 170 mm (5.91 to 6.69 in.) |
| *c | 150 to 170 mm (5.91 to 6.69 in.) | *d | 270 to 290 mm (10.6 to 11.4 in.) |
for RHD:
Install 3 new wire harness clamps to the wire harness as shown in the illustration.
| *1 | Torque Sensor Wire Harness | *2 | Power Steering Motor Wire Harness |
| *3 | Wire Harness Clamp | - | - |
| *a | 260 to 280 mm (10.2 to 11.0 in.) | *b | 130 to 150 mm (5.12 to 5.91 in.) |
| *c | 135 to 155 mm (5.31 to 6.10 in.) | *d | 265 to 285 mm (10.4 to 11.2 in.) |
84450
2.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)
Engage the 2 claws to install the ignition or starter switch assembly to the upper steering column bracket assembly.
85432
3.INSTALL KEY INTERLOCK SOLENOID (except Manual Transaxle without Smart Entry and Start System)
Engage the claw to install the key interlock solenoid to the upper steering column bracket assembly.
Install the screw.
84052
4.INSTALL UNLOCK WARNING SWITCH ASSEMBLY (w/o Smart Entry and Start System)
Engage the 2 claws to install the unlock warning switch assembly.
Slide the unlock warning switch assembly in the direction shown by the arrow in the illustration to install it.
69057A
5.INSTALL IGNITION SWITCH LOCK CYLINDER AND KEY SET (w/o Smart Entry and Start System)
Secure the steering column assembly in a vise using aluminum plates.
Do not overtighten the vise.
Install the ignition switch lock cylinder and key set with a new steering lock set bolt, and then tighten the steering lock set bolt until its head comes off.
45020A
6.INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System)
Secure the steering column assembly in a vise using aluminum plates.
Do not overtighten the vise.
Install the steering lock actuator assembly with a new steering lock set bolt, and then tighten the steering lock set bolt until its head comes off.
45260
7.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
| *a | Alignment Mark |
| *b | Slit |
Align the slit of the No. 2 steering intermediate shaft assembly with the alignment mark of the steering column assembly.
Install the No. 2 steering intermediate shaft assembly to the steering column assembly with the bolt.
45209
8.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY
| *a | Matchmark |
Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering sliding yoke sub-assembly and temporarily install them with the bolt.
89658
9.INSTALL POWER STEERING ECU BRACKET (for 1NZ-FE, 2NZ-FE)
Install the power steering ECU bracket to the steering column assembly with the 2 bolts.
Install a new wiring harness clamp assembly to the steering column assembly.
After installing the wiring harness clamp assembly, cut away any excess band.