Home › Drivetrain › K411 CVT › REVOLUTION SENSOR › from 2016.04
RM30M0E _52 Drivetrain _052750 K411 CVT _0259920 REVOLUTION SENSOR G

K411 CVT  REVOLUTION SENSOR  INSPECTION  


PROCEDURE

Hide 89413B 1.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)

a.

Check the resistance.

i.
C221276C11
0.865,1.25 1.427,1.25 true 2,1.25 2.563,1.25 true 0.177,0.219 0.365,0.406 0.188,0.188 10 false *a 0.5,1.177 0.854,1.354 0.354,0.177 10 false NIN+ 2.615,1.167 2.938,1.323 0.323,0.156 10 false NIN-
*a Component without harness connected
(Transmission Revolution Sensor (NIN))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω


If the result is not as specified, replace the transmission revolution sensor (NIN).



Hide 89413B 2.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

a.

Check the current.

i.

Connect the battery to the transmission revolution sensor (NOUT) as shown in the illustration.


ii.

Wave a magnetic object left and right in front of the transmission revolution sensor (NOUT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

C173707C09
4.865,0.365 6.792,2.438 1.927,2.073 1.667,1.229 1.938,1.031 false 2.49,0.615 2.198,0.833 false 5.292,2.115 5.646,1.583 true 6.365,2.115 6.01,1.583 true 4.938,0.438 5.156,0.656 0.219,0.219 10 false *e 0.625,1.688 0.865,1.896 0.24,0.208 10 false *a 1.542,1.146 1.677,1.344 0.135,0.198 10 false 2 2.531,0.5 2.667,0.698 0.135,0.198 10 false 1 5.094,2.115 5.563,2.323 0.469,0.208 10 false NOTB 6.208,2.125 6.698,2.333 0.49,0.208 10 false NOTO 0.646,0.51 0.854,0.688 0.208,0.177 10 false *b 2.958,2.125 3.156,2.313 0.198,0.188 10 false *d 3.854,1.792 4.073,1.99 0.219,0.198 10 false *c
*a Battery *b Ammeter
*c Magnet *d 5 mm (0.197 in.) or less
*e Component without harness connected
(Transmission Revolution Sensor (NOUT))
- -


NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



iii.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low Signal 4 to 8 mA
High Signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NOUT).



Hide 89413B 3.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

a.

Check the current.

i.

Connect the battery to the transmission revolution sensor (NT) as shown in the illustration.


ii.

Wave a magnetic object left and right in front of the transmission revolution sensor (NT) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

C154686C42
4.802,0.385 6.844,2.448 2.042,2.063 2.906,0.333 3.219,0.188 false 2.229,0.688 2.542,0.542 false 5.292,2.125 5.635,1.583 true 6.333,2.115 6,1.583 true 0.667,0.281 0.906,0.448 0.24,0.167 10 false *b 2.125,0.615 2.25,0.792 0.125,0.177 10 false 2 3.26,0.083 3.385,0.26 0.125,0.177 10 false 1 0.635,1.458 0.823,1.625 0.188,0.167 10 false *a 2.625,2.094 2.813,2.302 0.188,0.208 10 false *d 3.542,1.802 3.729,2.01 0.188,0.208 10 false *c 4.885,0.458 5.073,0.667 0.188,0.208 10 false *e 5.156,2.135 5.615,2.333 0.458,0.198 10 false NTB 6.229,2.135 6.688,2.333 0.458,0.198 10 false NTO
*a Battery *b Ammeter
*c Magnet *d 5 mm (0.197 in.) or less
*e Component without harness connected
(Transmission Revolution Sensor (NT))
- -


NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



iii.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low Signal 4 to 8 mA
High Signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NT).