Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › 2016.04–2016.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090850 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG circuit or IG hold circuit in the certification ECU (smart key ECU assembly) is detected.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit in the certification ECU (smart key ECU assembly) is malfunctioning.

·

The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning.


·

AM2 NO. 2 fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Turn the engine switch on (IG).
HINT:

To turn the engine switch on (IG), carry an electrical key transmitter sub-assembly and press the engine switch twice with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 released.



*1: Only detected while a malfunction is present and the engine switch is on (IG).

*2: for Automatic Transaxle and CVT

*3: for Manual Transaxle


HINT:
·

The IG circuit activate the No. 1 ignition relay and No. 2 ignition relay.

·

After the IG circuit turn on, even if the CPU operates incorrectly, the IG hold circuit maintains the power source mode in on (IG).



Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine switch cannot be turned on (IG) (the engine cannot be started). The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2271
Power Source Control
·

IG Relay Monitor (Inside)

·

Latch Circuit


Starting Control
·

Ignition


-

WIRING DIAGRAM

B342620E01
0.073,0.656 0.938,0.896 0.865,0.24 10 false from Battery 1.26,0.844 2.125,1.083 0.865,0.24 10 false AM2 NO. 2 2.49,3.833 2.948,4.073 0.458,0.24 10 false F43 2.479,3.99 4.021,4.396 1.542,0.406 10 false Certification ECU (Smart Key ECU Assembly) 4.583,3.438 5.833,3.667 1.25,0.229 10 false No. 2 Ignition Relay 4.583,3.271 5.042,3.51 0.458,0.24 10 false F77 5.719,3.74 6.969,3.979 1.25,0.24 10 false from AM2 Fuse 6.396,2.521 6.99,2.76 0.594,0.24 10 false to Fuses 6.406,0.938 7,1.177 0.594,0.24 10 false to Fuses 5.729,0.344 6.979,0.583 1.25,0.24 10 false from AM1 Fuse 3.125,1.354 3.5,1.563 0.375,0.208 10 false IG1D 2.688,0.656 3.063,0.865 0.375,0.208 10 false +B 3.552,1.24 3.927,1.448 0.375,0.208 10 false 20 2.698,3.021 3.073,3.229 0.375,0.208 10 false E 2.427,2.938 2.802,3.146 0.375,0.208 10 false 10 2.479,0.542 2.688,0.76 0.208,0.219 10 false 1 4.771,0.833 4.979,1.052 0.208,0.219 10 false 5 5.552,1.26 5.76,1.479 0.208,0.219 10 false 2 4.771,1.25 4.979,1.469 0.208,0.219 10 false 1 4.76,2.427 4.969,2.646 0.208,0.219 10 false 3 4.604,1.688 5.063,1.927 0.458,0.24 10 false F76 4.604,1.854 5.854,2.063 1.25,0.208 10 false No. 1 Ignition Relay 5.563,2.417 5.771,2.635 0.208,0.219 10 false 5 4.771,2.833 4.979,3.052 0.208,0.219 10 false 2 5.563,2.854 5.771,3.073 0.208,0.219 10 false 1 5.542,0.833 5.75,1.052 0.208,0.219 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B342622C01
1.5,0.25 1.917,0.5 0.417,0.25 0.573,1.115 0.333,1.75 true 0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 1.594,0.292 2.052,0.49 0.458,0.198 10 false F43 0.219,1.771 0.677,1.969 0.458,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F43-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B342622C02
1.5,0.25 1.927,0.5 0.427,0.25 2.813,1.146 3.083,1.75 true 0.042,0.042 0.354,0.198 0.313,0.156 10 false *a 1.583,0.271 2.042,0.469 0.458,0.198 10 false F43 3.063,1.792 3.219,1.99 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the certification ECU (smart key ECU assembly) connector.

B342590C02
2.5,0.333 2.917,0.583 0.417,0.25 2.573,1.427 2.083,2.167 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 1.927,2.167 2.333,2.417 0.406,0.25 10 false IG1D 2.583,0.354 3.042,0.552 0.458,0.198 10 false F43
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - Body ground Engine switch on (ACC) → Engine switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)