Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › DRIVE BELT › 2016.04–2017.10
RM30M0E _51 Engine / Hybrid System _053933 2NR-FE ENGINE MECHANICAL _0262359 DRIVE BELT A

2NR-FE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.
A382558C01
0.583,1.719 0.99,1.51 true 2.635,0.979 2.271,1.094 true 2.313,0.5 2.656,0.333 true 0.542,4.156 1,3.927 true 2.323,2.958 2.719,2.833 true 2.271,3.583 2.698,3.469 true 2.396,4.125 2.76,3.99 false 0.073,0.063 0.521,0.427 0.448,0.365 12 false *A 0.073,2.417 0.479,2.75 0.406,0.333 12 false *B 0.417,1.667 0.729,1.823 0.313,0.156 10 false *1 2.708,0.24 3.021,0.396 0.313,0.156 10 false *2 2.677,0.917 2.99,1.073 0.313,0.156 10 false *3 2.792,3.906 3.104,4.063 0.313,0.156 10 false *4 0.354,4.094 0.667,4.292 0.313,0.198 10 false *1 2.792,2.781 3.104,2.979 0.313,0.198 10 false *2 2.729,3.385 3.042,3.583 0.313,0.198 10 false *3
*A w/o Air Conditioning System
*B w/ Air Conditioning System
*1 Crankshaft Pulley
*2 Generator with Regulator Assembly
*3 Engine Water Pump Assembly
*4 Cooler Compressor Assembly


Install the fan and generator V belt to each pulley.


b.

If it is difficult to install the fan and generator V belt, perform the following procedure:

i.

Install the fan and generator V belt on each pulley except the tensioner pulley as shown in the illustration.


ii.

Release the fan and generator V belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and install the fan and generator V belt on the tensioner pulley.

NOTICE:
·

Install the backside of the fan and generator V belt on the V-ribbed belt tensioner pulley.

·

Check that the fan and generator V belt is properly installed to each pulley.





c.
A383343C01
1.375,1.24 1.292,0.917 true 1.323,1.24 1.635,1.396 0.313,0.156 10 false *a 0.031,2.385 0.344,2.542 0.313,0.156 10 false *b
*a 5 mm Hexagon Wrench
*b Turn


Turn the V-ribbed belt tensioner assembly counterclockwise and remove the 5 mm hexagon wrench.


d.

After installing the fan and generator V belt, check that it fits properly in the ribbed grooves. Confirm that the belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.


Hide 51441C 2.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

a.

Install engine under cover RH to the vehicle with the 2 bolts and 4 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51405A 3.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 4.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)