Home › Engine / Hybrid System › 1NR-FE STARTING › STARTER › from 2016.04
RM30M0E _51 Engine / Hybrid System _053949 1NR-FE STARTING _0262381 STARTER G

1NR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A331207C01
1.323,0.406 1.51,0.406 1.51,0.406 2,0.594 true 2.594,2.365 2.594,1.823 true 2.521,2.385 2.833,2.542 0.313,0.156 10 false *a 1.146,0.333 1.458,0.49 0.313,0.156 10 false *b
*a Terminal 50
*b Body


Connect the battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.



b.
A331208C01
1.188,0.396 1.396,0.396 1.396,0.396 2,0.646 true 2.583,2.313 2.583,1.813 true 2.51,2.323 2.823,2.479 0.313,0.156 10 false *a 1,0.313 1.313,0.469 0.313,0.156 10 false *b
*a Terminal 50
*b Body


Check return operation.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear moves inward.

If the clutch pinion gear does not move inward, replace the magnet starter switch assembly.



c.

Perform a no-load performance test.

i.

Clamp the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter is secured in the vise to prevent it from falling out.



ii.
A331209C01
2.583,1.958 2.583,1.792 true 2.604,1.583 3.146,1.667 3.146,1.667 3.146,1.771 true 1.365,0.406 1.563,0.406 1.563,0.406 1.99,0.604 true 2.5,1.958 2.813,2.115 0.313,0.156 10 false *a 3.073,1.792 3.313,2 0.24,0.208 10 false *b 1.188,0.313 1.5,0.469 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal 30
*c Body


Connect the battery and an ammeter to the starter as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the pinion gear operates.



iii.

Check that the starter rotates smoothly and steadily with the pinion gear moved outward.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for an open circuit.

i.
A247248C09
2.26,1.031 1.115,1.563 1.115,1.563 2.115,1.302 true 0.917,1.479 1.26,1.688 0.344,0.208 10 *a
*a Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



b.

Check the commutator for a short circuit.

i.
A247247C07
2.25,1.177 2.76,1.552 true 1.438,0.917 1.76,1.604 true 2.813,1.49 3.146,1.667 0.333,0.177 10 *a 1.74,1.625 2.052,1.802 0.313,0.177 10 *b
*a Commutator
*b Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Commutator - Coil Core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.

Check the commutator for dirt and burns on the surface.

If the surface is dirty or burnt, restore it with sandpaper (No. 400) or on a lathe.


d.

Check the commutator for runout.

i.
A247250

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the runout.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the starter armature assembly.



e.
A331236C01
0.104,0.49 0.375,0.688 0.271,0.198 10 false *a
*a Diameter


Using a vernier caliper, measure the commutator diameter.

Standard diameter:

25.0 mm (0.984 in.)


Minimum diameter:

24.0 mm (0.945 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A247252C01
3.167,0.969 3.385,1.167 0.219,0.198 10 true *a
*a Undercut Depth


Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A248655

Using a vernier caliper, measure the brush length.

Standard length:

11.6 mm (0.457 in.)


Minimum length:

7.6 mm (0.299 in.)


If the length is less than the minimum, replace the starter brush holder assembly.


Hide 28021 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A247253C01
1.781,2.844 2.042,3.052 0.26,0.208 10 *b 1.802,1.896 2.167,2.146 0.365,0.25 10 *a
*a Free
*b Lock


While holding the starter center bearing clutch sub-assembly, rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If necessary, replace the starter center bearing clutch sub-assembly.


Hide 28150 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A247243C07
2.49,0.604 2.25,0.229 2.25,0.229 2.073,0.229 false 1.885,0.146 2.177,0.344 0.292,0.198 10 false *a
*a Plunger


Push in the plunger and check that it returns quickly to its original position.

If necessary, replace the magnet starter switch assembly.

NOTICE:

To avoid damaging the inside of the magnet starter switch assembly, do not release the plunger quickly.




b.

Check the hold-in coil for an open circuit.

i.
A247245C09
2.5,0.969 2.99,0.594 true 1.542,0.854 1.177,0.448 1.177,0.448 0.906,0.448 true 3.052,0.49 3.344,0.646 0.292,0.156 10 false *a 0.708,0.375 1,0.563 0.292,0.188 10 false *b
*a Terminal 50
*b Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.