Home › Engine / Hybrid System › 1NR-FE STARTING › STARTER › from 2016.04
RM30M0E _51 Engine / Hybrid System _053949 1NR-FE STARTING _0262381 STARTER A

1NR-FE STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A248656C09
1.833,0.938 2.969,0.5 2.969,0.5 1.698,1.354 true 2.042,1.417 2.958,0.51 true 3.01,0.396 3.323,0.552 0.313,0.156 10 false *a
*a Pins without Depressions
V100135

High-temperature Grease


Apply high-temperature grease to the 3 planetary gears and the starter center bearing clutch sub-assembly.

HINT:

Apply a total of approximately 0.5 g of high-temperature grease to the planetary gears, end section, and pins without depressions.



b.
A248654C13
1.292,1.052 0.51,1.573 0.51,1.573 1.177,1.448 true 0.51,1.573 1.51,1.521 true 0.292,1.51 0.5,1.729 0.208,0.219 10 false *a
*a Pins without Depressions


Install the 3 planetary gears to the pins without depressions on the starter center bearing clutch sub-assembly.


c.
A379540

Attach the 3 claws and install the internal gear to the starter center bearing clutch sub-assembly.


d.
A379541C04
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the drive lever contact surfaces.

HINT:

Apply approximately 0.1 g of high-temperature grease to each section.



e.
A379542C04
2.469,1.042 2.802,1.042 false 1.948,0.729 2.333,0.333 2.333,0.333 2.5,0.333 false 2.594,0.229 2.906,0.427 0.313,0.198 10 false *a 2.865,0.938 3.177,1.135 0.313,0.198 10 false *b
*a Depression
*b Protrusion


Align the depression of the starter drive housing with the protrusion of the starter center bearing clutch sub-assembly and install the starter center bearing clutch sub-assembly.


f.

Install the rubber seal to the starter drive housing.


Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A248658C02
0.75,0.844 1.385,0.615 1.385,0.615 0.927,1.667 true 2.333,0.823 3.115,0.292 3.115,0.292 2.833,1.667 true 1.417,0.479 1.729,0.635 0.313,0.156 10 false *a 3.177,0.188 3.406,0.396 0.229,0.208 10 false *b
*a Protrusion
*b Depression


Install the commutator end frame to the starter brush holder assembly as shown in the illustration.

HINT:

If the bolt holes are misaligned, the through bolts cannot be installed.



b.
A248796

Spread the brushes on the starter brush holder assembly, and install the starter armature assembly to the starter brush holder assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A248842C03
1.604,0.99 0.948,0.99 false 0.729,0.906 0.906,1.073 0.177,0.167 10 *a
*a Hammer


While holding down the starter armature assembly and the starter brush holder assembly with the handle of a hammer, install the starter yoke assembly.

HINT:

The starter armature assembly will be attracted by the magnetic field of the starter yoke assembly, so hold the starter armature assembly with the handle of the hammer.



Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.
A379543C04
1.51,0.677 1.583,0.25 1.583,0.25 1.75,0.25 true 0.979,0.75 1.063,0.25 1.063,0.25 1.229,0.25 false 1.323,0.146 1.635,0.344 0.313,0.198 10 false *a 1.813,0.146 2.125,0.344 0.313,0.198 10 false *b
*a Protrusion
*b Cutout


Align the cutout of the starter yoke assembly with the protrusion of the starter center bearing clutch sub-assembly.


b.

Using a 7 mm socket wrench, install the starter yoke assembly with the 3 through bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 28150 5.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A331202C01
1.385,0.573 1.552,0.458 1.552,0.458 1.677,0.458 false 1.313,1.417 1.49,1.417 1.49,1.417 1.677,1.156 false 1.719,0.365 2.052,0.552 0.333,0.188 10 false *a 1.135,1.333 1.448,1.49 0.313,0.156 10 false *b
*a Drive Lever
*b Hook


Catch the hook on the magnet starter switch assembly on the drive lever from the top.


b.
A331212C01
1.094,2.594 1.292,2.594 true 0.917,2.5 1.229,2.656 0.313,0.156 10 false *a
*a Terminal C


Push down the rear of the magnet starter switch assembly and connect it to terminal C.

NOTICE:
·

Connect the magnet starter switch assembly securely to terminal C.

·

Check that the parts are free of foreign matter, oil, or grease.




c.

Using a 7 mm socket wrench, install the magnet starter switch assembly with the 2 bolts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)