Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2016.04–2016.07
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090852 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


B343137E02
3.417,0.25 3.833,0.5 0.417,0.25 3.51,0.292 3.969,0.49 0.458,0.198 10 false F51

a.

Disconnect the F51 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F51-7 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F51-1 (+B) - F51-7 (GND) Input SB - W-B Battery Always 11 to 14 V +B
F51-2 (IG) - F51-7 (GND) Input V - W-B Ignition switch Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the F51 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F51-3 (IND) - F51-7 (GND) Output P - W-B Security indicator signal No key in ignition key cylinder, or 20 seconds elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Ignition switch ON (immobiliser system unset) Below 1 V
F51-6 (D) - F51-7 (GND) Input/Output G - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
F51-5 (EFII) - F51-7 (GND) Output BR - W-B ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
F51-4 (EFIO) - F51-7 (GND) Input G - W-B ECM output signal Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)

If the result is not as specified, the transponder key ECU assembly may be malfunctioning.


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B325134C08
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F51-5 (EFII) - F51-7 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C09
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F51-4 (EFIO) - F51-7 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for Automatic Transaxle or for 1NZ-FE with Manual Transaxle with Air Fuel Ratio Sensor)


A301712E06
1.25,0.25 1.667,0.5 0.417,0.25 2.583,0.25 3,0.5 0.417,0.25 4.083,0.25 4.5,0.5 0.417,0.25 4.083,0.25 4.5,0.5 0.417,0.25 5.333,0.25 5.75,0.5 0.417,0.25 1.333,0.281 1.792,0.479 0.458,0.198 10 false B29 2.667,0.292 3.125,0.49 0.458,0.198 10 false B31 5.427,0.292 5.885,0.49 0.458,0.198 10 false F83 4.167,0.281 4.625,0.479 0.458,0.198 10 false F82

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
B29-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B29-2 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B29-6 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B31-2 (E03) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B29-5 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F83-1 (+B) - B29-1 (E1) Input R - W-B +B power supply Ignition switch ON 11 to 14 V -
F83-2 (+B2) - B29-1 (E1) Input R - W-B +B power supply Ignition switch ON 11 to 14 V -
F83-4 (BATT) - B29-1 (E1) Input G - W-B +B power supply Always 11 to 14 V -
F82-15 (IMO) - B29-1 (E1) Input BR - W-B Transponder key ECU assembly communication input Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
F82-16 (IMI) - B29-1 (E1) Output G - W-B Transponder key ECU assembly communication output Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission

If the result is not as specified, the ECM may be malfunctioning.


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C05
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F82-15 (IMO) - B29-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C10
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F82-16 (IMI) - B29-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1NZ-FE with Manual Transaxle without Air Fuel Ratio Sensor or for 2NZ-FE with Manual Transaxle)


A295438E02
2,0.667 2.417,0.917 0.417,0.25 3.375,0.667 3.792,0.917 0.417,0.25 4.729,0.667 5.146,0.917 0.417,0.25 2.094,0.698 2.552,0.896 0.458,0.198 10 false F81 3.458,0.688 3.917,0.885 0.458,0.198 10 false B30 4.813,0.698 5.271,0.896 0.458,0.198 10 false B32

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
B32-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B30-2 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B32-5 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B30-1 (E03) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B32-6 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F81-10 (+B) - B32-1 (E1) Input R - W-B +B power supply Ignition switch ON 11 to 14 V -
F81-9 (BATT) - B32-1 (E1) Input G - W-B +B power supply Always 11 to 14 V -
F81-18 (IMO) - B32-1 (E1) Input BR - W-B Transponder key ECU assembly communication input Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
F81-19 (IMI) - B32-1 (E1) Output G - W-B Transponder key ECU assembly communication output Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission

If the result is not as specified, the ECM may be malfunctioning.


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C06
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F81-18 (IMO) - B32-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C11
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F81-19 (IMI) - B32-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for CVT)


A371911E12
0.667,0.583 1,0.75 0.333,0.167 2.083,0.583 2.417,0.75 0.333,0.167 3.5,0.583 3.833,0.75 0.333,0.167 4.833,0.583 5.167,0.75 0.333,0.167 6.083,0.583 6.417,0.75 0.333,0.167 0.719,0.583 1.177,0.781 0.458,0.198 10 false B46 2.135,0.583 2.594,0.781 0.458,0.198 10 false B47 3.552,0.583 4.01,0.781 0.458,0.198 10 false B48 4.844,0.583 5.302,0.781 0.458,0.198 10 false F130 6.094,0.583 6.552,0.781 0.458,0.198 10 false F131

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
B46-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B46-4 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B46-1 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B46-2 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F131-1 (+B) - B46-3 (E1) Input R - W-B +B power supply Ignition switch ON 11 to 14 V -
F131-2 (+B2) - B46-3 (E1) Input R - W-B +B power supply Ignition switch ON 11 to 14 V -
F131-3 (BATT) - B46-3 (E1) Input G - W-B +B power supply Always 11 to 14 V -
F130-9 (IMO) - B46-3 (E1) Input BR - W-B Transponder key ECU assembly communication input Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
F130-10 (IMI) - B46-3 (E1) Output G - W-B Transponder key ECU assembly communication output Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission

If the result is not as specified, the ECM may be malfunctioning.


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C05
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F130-9 (IMO) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C10
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F130-10 (IMI) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1NR-FE with Manual Transaxle or for 2NR-FE with Manual Transaxle)


A301712E19
1.25,0.25 1.667,0.5 0.417,0.25 2.583,0.25 3,0.5 0.417,0.25 4.083,0.25 4.5,0.5 0.417,0.25 4.083,0.25 4.5,0.5 0.417,0.25 5.333,0.25 5.75,0.5 0.417,0.25 1.333,0.281 1.792,0.479 0.458,0.198 10 false B46 2.667,0.292 3.125,0.49 0.458,0.198 10 false B47 5.406,0.292 5.865,0.49 0.458,0.198 10 false F131 4.156,0.292 4.615,0.49 0.458,0.198 10 false F130

a.

Measure the resistance, voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
B46-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B46-4 (ME01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B46-1 (E01) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
B46-2 (E02) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F131-1 (+B) - B46-3 (E1) Input R - W-B +B power supply Ignition switch ON 11 to 14 V -
F131-2 (+B2) - B46-3 (E1) Input R - W-B +B power supply Ignition switch ON 11 to 14 V -
F131-3 (BATT) - B46-3 (E1) Input G - W-B +B power supply Always 11 to 14 V -
F130-9 (IMO) - B46-3 (E1) Input BR - W-B Transponder key ECU assembly communication input Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
E/G Start Permission
F130-10 (IMI) - B46-3 (E1) Output G - W-B Transponder key ECU assembly communication output Ignition switch off Below 1 V E/G Start Permission
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
E/G Start Permission

If the result is not as specified, the ECM may be malfunctioning.


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C05
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F130-9 (IMO) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 2 (Reference)

B333259C10
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F130-10 (IMI) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal