If an error in transponder key ECU assembly occurs, this symptom may occur.
Refer to "System Diagram".
If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| Immobiliser Fuel Cut |
Perform the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser system fuel cut | ON or OFF | - | - |
OFF is displayed after the engine is started
| Result | Proceed to |
|---|---|
| OK (for 1NZ-FE with Automatic Transaxle) | A |
| OK (for 1NZ-FE with Manual Transaxle) | B |
| OK (for 1NZ-FE with Air Fuel Ratio Sensor) | C |
| OK (for 2NZ-FE with Automatic Transaxle) | D |
| OK (for 2NZ-FE with Manual Transaxle) | E |
| OK (for 1NR-FE) | F |
| OK (for 2NR-FE) | G |
| NG | H |
A
B
C
D
E
F
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
G
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
H
Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.
Security indicator light turns OFF
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.
Security indicator light turns OFF
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using another registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the key.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the key.
Key ID code registration is necessary when replacing the key.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NZ-FE with Automatic Transaxle) | B |
| NG (for 1NZ-FE with Manual Transaxle) | C |
| NG (for 1NZ-FE with Air Fuel Ratio Sensor) | D |
| NG (for 2NZ-FE with Automatic Transaxle) | E |
| NG (for 2NZ-FE with Manual Transaxle) | F |
| NG (for 1NR-FE) | G |
| NG (for 2NR-FE) | H |
A
B
C
D
E
F
G
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
H
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING