Home › Engine / Hybrid System › 1NR-FE ENGINE MECHANICAL › CYLINDER HEAD › from 2016.04
RM30M0E _51 Engine / Hybrid System _053932 1NR-FE ENGINE MECHANICAL _0262435 CYLINDER HEAD A

1NR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).

CAUTION:

Make sure not to burn yourself.



b.
A305672C01
2.844,2.719 2.427,2.927 2.427,2.927 3.24,1.823 true 1.563,1.313 0.917,0.552 0.917,0.552 1.521,0.896 true 2.24,2.958 2.552,3.115 0.313,0.156 10 false *a 0.573,0.458 1.031,0.656 0.458,0.198 10 false SST
*a Wooden Block


Place the cylinder head sub-assembly on wooden blocks.


c.

Using SST and a hammer, tap out the intake valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A198025

Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head sub-assembly.

Standard bush bore diameter:

10.285 to 10.306 mm (0.40493 to 0.40574 in.)


New Guide Bush Selection Chart (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.285 to 10.306 mm (0.40493 to 0.40574 in.)
O/S 0.05 10.335 to 10.356 mm (0.40689 to 0.40771 in.)


If the intake valve guide bush bore diameter of the cylinder head sub-assembly is greater than 10.306 mm (0.40574 in.), machine the bush bore to the diameter of 10.335 to 10.356 mm (0.40689 to 0.40771 in.) to install an O/S 0.05 valve guide bush. If the intake valve guide bush bore diameter of the cylinder head sub-assembly is greater than 10.356 mm (0.40771 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).

CAUTION:

Make sure not to burn yourself.



f.
A305674C01
2.76,2.708 2.365,2.885 2.365,2.885 3.208,1.802 true 1.563,1.323 0.99,0.552 0.99,0.552 1.552,0.938 true 2.208,2.948 2.521,3.104 0.313,0.156 10 false *a 0.625,0.438 1.083,0.635 0.458,0.198 10 false SST
*a Wooden Block


Place the cylinder head sub-assembly on wooden blocks.


g.

Using SST and a hammer, tap a new intake valve guide bush into the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.65 to 9.90 mm (0.380 to 0.390 in.)



h.
A198023C01
0.448,1.573 0.354,0.854 0.354,0.854 1.542,1.208 true 0.135,0.74 0.448,0.896 0.313,0.156 10 false *a
*a Sharp 5.5 mm Reamer


Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard oil clearance between the intake valve guide bush and intake valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.00099 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).

CAUTION:

Make sure not to burn yourself.



b.

Place the cylinder head sub-assembly on wooden blocks.


c.
A305676C01
2.573,2.573 2.073,2.896 2.073,2.896 2.99,1.698 true 1.698,1.469 1.208,0.552 1.208,0.552 1.771,1.021 true 1.938,2.927 2.25,3.083 0.313,0.156 10 false *a 0.875,0.448 1.333,0.646 0.458,0.198 10 false SST
*a Wooden Block


Using SST and a hammer, tap out the exhaust valve guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A198024

Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head sub-assembly.

Standard bush bore diameter:

10.285 to 10.306 mm (0.40493 to 0.40574 in.)


New Guide Bush Selection Chart (STD or O/S 0.05):
Bush Size Bush Bore Diameter
STD 10.285 to 10.306 mm (0.40493 to 0.40574 in.)
O/S 0.05 10.335 to 10.356 mm (0.40689 to 0.40771 in.)


If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is greater than 10.306 mm (0.40574 in.), machine the bush bore to the diameter of 10.335 to 10.356 mm (0.40689 to 0.40771 in.) to install an O/S 0.05 valve guide bush. If the exhaust valve guide bush bore diameter of the cylinder head sub-assembly is greater than 10.356 mm (0.40771 in.), replace the cylinder head sub-assembly.


e.

Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).

CAUTION:

Make sure not to burn yourself.



f.
A305678C01
2.49,2.583 2.094,2.833 2.094,2.833 2.99,1.656 true 1.708,1.427 1.208,0.5 1.208,0.5 1.802,1.031 true 2,2.854 2.313,3.01 0.313,0.156 10 false *a 0.906,0.417 1.365,0.615 0.458,0.198 10 false SST
*a Wooden Block


Place the cylinder head sub-assembly on wooden blocks.


g.

Using SST and a hammer, tap a new exhaust valve guide bush into the specified protrusion height.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.65 to 9.90 mm (0.380 to 0.390 in.)



h.
A198020C01
0.906,1.552 0.438,0.604 0.438,0.604 1.76,1.229 true 0.208,0.469 0.521,0.625 0.313,0.156 10 false *a
*a Sharp 5.5 mm Reamer


Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard oil clearance between the exhaust valve guide bush and exhaust valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00119 to 0.00255 in.)



Hide 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.

Remove the 4 ring pins.


b.

Using a plastic hammer, tap in 4 new ring pins to the specified protrusion height.

A381459C01
4.469,0.865 4.75,1 4.75,1 4.75,1.167 false 1.49,0.365 1.646,0.563 0.156,0.198 10 false B 1.667,0.365 1.823,0.563 0.156,0.198 10 false B 0.802,1.708 0.958,1.906 0.156,0.198 10 false A 3.563,1.885 3.719,2.083 0.156,0.198 10 false A 3.844,0.052 4,0.25 0.156,0.198 10 false A 5,0.052 5.156,0.25 0.156,0.198 10 false B 3.594,0.313 4.833,0.479 1.24,0.167 10 false 11.0 mm (0.433 in.) 4.875,0.323 6.115,0.49 1.24,0.167 10 false 12.0 mm (0.472 in.) 5.688,0.74 6.865,1.146 1.177,0.406 10 false 11.7 to 12.3 mm (0.461 to 0.484 in.) 6.083,1.594 7.073,1.76 0.99,0.167 10 false 6.0 to 8.0 mm 4.26,1.177 5.448,1.542 1.188,0.365 10 false 10.7 to 11.3 mm (0.421 to 0.444 in.)
*a Upper Side - -


Protrusion Height:

6.0 to 8.0 mm (0.237 to 0.314 in.)



Hide 4.REPLACE STUD BOLT

NOTICE:

If any of the stud bolts is deformed or the threads are damaged, replace it.


a.

Using an E8 "TORX" socket wrench, remove the 7 stud bolts.


b.

Using an E8 "TORX" socket wrench, install the 7 stud bolts.

A313201C05
0.333,0.177 0.646,0.333 0.313,0.156 10 false *a 3.604,0.188 3.917,0.344 0.313,0.156 10 false *b 1.76,0.698 2.135,0.938 0.375,0.24 12 false A 2.365,0.698 2.74,0.938 0.375,0.24 12 false A 1.635,2.573 2.01,2.813 0.375,0.24 12 false A 4.5,2.792 4.708,3 0.208,0.208 12 false B 4.833,1.781 5.021,2.01 0.188,0.229 12 false B 5.385,1.781 5.542,1.979 0.156,0.198 12 false B 3.823,0.927 4,1.104 0.177,0.177 12 true B 4.854,0.896 4.99,1.083 0.135,0.188 12 true B 6.146,0.917 6.292,1.094 0.146,0.177 12 true B 2.188,3.26 2.833,3.667 0.646,0.406 10 false 26.0 mm (1.024 in.) 2.958,3.479 3.583,3.927 0.625,0.448 10 false 48.0 mm (1.890 in.) 2.156,4.146 2.833,4.51 0.677,0.365 10 false 13.0 mm (0.512 in.) 5.844,3.719 6.469,4.083 0.625,0.365 10 false 35.0 mm (1.378 in.) 5.042,3.552 5.708,3.917 0.667,0.365 10 false 20.0 mm (0.787 in.) 5.042,4.135 5.667,4.5 0.625,0.365 10 false 13.0 mm (0.512 in.)
*a Intake Side *b Exhaust Side


Torque:
Stud bolt A and B : 9.5 N*m (97 kgf*cm, 84 in.*lbf)