Home › Engine / Hybrid System › 1NR-FE ENGINE MECHANICAL › CYLINDER HEAD › from 2016.04
RM30M0E _51 Engine / Hybrid System _053932 1NR-FE ENGINE MECHANICAL _0262435 CYLINDER HEAD A

1NR-FE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

a.
A204168C06
1.51,1.333 1.854,1.729 false 2.354,0.396 3.396,0.573 1.042,0.177 10 false *a 1.917,1.677 2.26,1.833 0.344,0.156 10 false *b
*a Protrusion Height
*b Paint Mark


Using paint, mark the standard position from the edge.

Standard protrusion height:

88.5 to 90.4 mm (3.484 to 3.559 in.)



b.
A204167C07
0.531,1.458 0.792,1.781 false 0.438,0.708 0.75,0.115 true 0.521,0.719 0.656,0.458 true 0.844,1.719 1.25,1.927 0.406,0.208 10 false *a 0.729,0.365 2.885,0.615 2.156,0.25 10 false 1.0 to 3.0 mm (0.0394 to 0.118 in.) 0.833,0.031 2.917,0.26 2.083,0.229 10 false 3.0 to 9.0 mm (0.118 to 0.354 in.)
*a Adhesive


Apply adhesive to the spark plug tube where it will be pressed into the cylinder head sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.
A286219C04
0.958,0.333 1.281,0.479 false 1.646,0.313 1.927,0.188 false 1.438,2.906 1.76,3.229 true 1.25,2.75 1.563,2.948 0.313,0.198 10 false *a 2.219,2.594 2.531,2.792 0.313,0.198 10 false *b 1.948,0.063 2.26,0.26 0.313,0.198 10 false *d 0.771,0.198 1.083,0.396 0.313,0.198 10 false *c
*a Paint Mark
*b Protrusion Height
*c Wooden Block
*d Press


Using a press and wooden block, press in the spark plug tube to the specified protrusion height.

Standard protrusion height:

88.5 to 90.4 mm (3.484 to 3.559 in.)


NOTICE:
·

Do not start the engine within 1 hour after installation.

·

Do not deform the spark plug tube.

·

Be careful not to drip the adhesive.




Hide 13734 2.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head sub-assembly.


Hide 3.INSTALL VALVE STEM OIL SEAL

a.
A146313C17
1.01,1.083 1.302,0.885 false 2.115,0.885 2.406,1.094 false 0.635,0.531 1.677,0.76 1.042,0.229 10 false *a 2.552,0.531 3.021,0.906 0.469,0.375 10 false *b 1.302,0.75 1.656,0.927 0.354,0.177 10 false *c 1.927,0.75 2.333,0.927 0.406,0.177 10 false *d
*a Intake Side
*b Exhaust Side
*c Silver
*d Black


Apply a light coat of engine oil to new valve stem oil seals.

NOTICE:

Pay close attention when installing the intake and exhaust valve stem oil seals. Installing the intake oil seal to the exhaust side or installing the exhaust valve stem oil seal to the intake side may cause installation problems later.


HINT:

The intake valve stem oil seal is silver and exhaust valve stem oil seal is black.



b.
A313204C01
1.5,0.74 1.073,0.25 true 2.792,0.917 2.313,0.229 true 3.167,0.729 2.979,0.229 true 1.552,2.771 1.083,3.115 1.083,3.115 0.635,2.781 true 1,3.146 1.313,3.302 0.313,0.156 10 false *1 0.333,2.385 0.677,2.583 0.344,0.198 10 false *a 1.604,2.365 1.917,2.521 0.313,0.156 10 false *b 0.917,0.083 1.26,0.281 0.344,0.198 10 false SST 2.146,0.094 2.458,0.25 0.313,0.156 10 false *1 2.833,0.063 3.177,0.26 0.344,0.198 10 false SST
*1 Valve Stem Oil Seal
*a Correct
*b Incorrect


Using SST, push in the valve stem oil seals.

SST
09201-41020  

NOTICE:

Make sure to use SST, or the valve stem oil seals may be damaged or improperly seated.



Hide 13711 4.INSTALL INTAKE VALVE

a.
A286223C02
2.635,1.573 2.948,1.771 0.313,0.198 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the intake valve shown in the illustration.


b.

Install the intake valve, outer compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts to their original positions.



c.
A198013C11
0.688,0.417 0.958,0.604 false 1.75,3.198 2.031,2.958 true 0.365,0.281 0.677,0.469 0.313,0.188 10 false SST 1.563,3.125 2.01,3.385 0.448,0.26 10 false *a
*a Wooden Block


Using SST and wooden blocks, compress the outer compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-00010)


d.
A198029

Using a plastic hammer, lightly tap the intake valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the intake valve stem tip.

·

Be careful not to tap the retainer.




Hide 13715 5.INSTALL EXHAUST VALVE

a.
A286224C02
2.635,1.656 2.948,1.854 0.313,0.198 10 *a
*a 30 mm (1.18 in.) or more


Sufficiently apply engine oil to the tip area of the exhaust valve shown in the illustration.


b.

Install the exhaust valve, outer compression spring and valve spring retainer to the cylinder head sub-assembly.

NOTICE:

Install the same parts to their original positions.



c.
A198015C11
1.927,0.698 2.188,0.427 false 1.958,3.115 2.271,2.833 true 2.229,0.292 2.625,0.479 0.396,0.188 10 false SST 1.771,3.052 2.156,3.281 0.385,0.229 10 false *a
*a Wooden Block


Using SST and wooden blocks, compress the outer compression spring and install the 2 valve spring retainer locks.

SST
09202-70020  (09202-00010)


d.
A198030

Using a plastic hammer, lightly tap the exhaust valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the exhaust valve stem tip.

·

Be careful not to tap the retainer.




Hide 13716 6.INSTALL VALVE STEM CAP

a.
A313196

Apply a light coat of engine oil to the valve stem caps.


b.

Install the valve stem caps to the intake valves and exhaust valves.