Perform "Inspection After Repair" after replacing the piston with pin sub-assembly or piston ring set.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
15708
1.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
Using a 5 mm socket hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies to the cylinder block sub-assembly with the 4 bolts.
13101
2.INSTALL PISTON WITH PIN SUB-ASSEMBLY
If the piston pin has been removed from the piston, replace the piston, piston pin and connecting rod with new ones.
Gradually heat a new connecting rod to 80°C (176°F) or more.
Make sure not to burn yourself.
| *a | Front Mark |
Coat a new piston pin and pin holes of a new piston with engine oil.
Align the front mark of the piston with that of the connecting rod.
Using SST, press in the piston pin.
| *1 | Piston Pin | *2 | Connecting Rod |
| *3 | Piston | - | - |
| *a | Front Mark | *b | Contact |
|
Rear Side | - | - |
Press in the piston pin from the side of the piston with the front mark as shown in the illustration.
With the connecting rod fully inserted into the piston end, press in the piston pin until it is flush with the piston surface.
Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
Perform "Inspection After Repair" after replacing the piston.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
13011
3.INSTALL PISTON RING SET
| *1 | Side Rail (Upper) |
| *2 | Expander Spacer |
| *3 | Side Rail (Lower) |
| *a | Expander Spacer and Side Rail Groove |
Install the expander spacer and 2 side rails by hand, as shown in the illustration.
| *1 | No. 1 Compression Ring |
| *2 | No. 2 Compression Ring |
|
Piston Top |
Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring as shown in the illustration.
Install the No. 2 compression ring with the code mark (T2) facing upward.
| *1 | No. 1 Compression Ring and Expander Spacer |
| *2 | No. 2 Compression Ring |
| *3 | Side Rail (Upper) |
| *4 | Side Rail (Lower) |
|
Engine Front |
Position the piston rings so that the ring ends are as shown in the illustration.
Perform "Inspection After Repair" after replacing the piston ring set.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
11711
4.INSTALL CRANKSHAFT BEARING
Install the 5 crankshaft bearings (upper) to the cylinder block sub-assembly.
| *a | Correct | *b | Incorrect |
|
Engine Front | - | - |
Align the oil holes in the crankshaft bearing with the oil holes in the cylinder block sub-assembly.
Do not apply engine oil to the crankshaft bearings or the contact surfaces.
Install the crankshaft bearing (lower).
Install the 5 crankshaft bearings (lower) to the 5 crankshaft bearing caps.
Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and crankshaft bearing (lower) edge.
0.8 mm (0.0315 in.) or less
Do not apply engine oil to the crankshaft bearings or the contact surfaces.
11791
5.INSTALL UPPER CRANKSHAFT THRUST WASHER
| *a | Oil Grooves |
Install the 2 upper crankshaft thrust washers under the No. 3 journal of the cylinder block sub-assembly with the oil grooves facing outward.
Apply engine oil to the 2 upper crankshaft thrust washers.
13411
6.INSTALL CRANKSHAFT
Apply engine oil to the crankshaft bearings (upper) and install the crankshaft on the cylinder block sub-assembly.
Apply engine oil to the crankshaft bearings (lower).
| *a | Number Mark |
|
Front |
Examine the number marks and install the crankshaft bearing caps on the cylinder block sub-assembly.
Apply a light coat of engine oil to the threads and under the crankshaft bearing cap set bolts.
Temporarily install the 10 crankshaft bearing cap set bolts.
Step 1
Uniformly tighten the 10 crankshaft bearing cap set bolts in the sequence shown in the illustration.
Step 2
| *a | Paint Mark |
|
Engine Front |
Mark the front of the crankshaft bearing cap set bolts with paint.
Further tighten the crankshaft bearing cap set bolts an additional 90° in the sequence shown in the previous illustration.
Check that the paint mark is now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Inspect the crankshaft thrust clearance.
Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION
13041
7.INSTALL CONNECTING ROD BEARING
Install the connecting rod bearing to the connecting rod and connecting rod cap.
Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing (upper) edge.
0.5 mm (0.0197 in.)
Do not apply engine oil to the connecting rod bearings or the contact surfaces.
Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing (lower) edge.
0.5 mm (0.0197 in.)
Do not apply engine oil to the connecting rod bearings or the connecting contact surfaces.
8.INSTALL PISTON WITH PIN SUB-ASSEMBLY WITH CONNECTING ROD SUB-ASSEMBLY
Apply engine oil to the cylinder walls, the pistons, and surfaces of the connecting rod bearings.
| *1 | No. 1 Compression Ring and Expander Spacer |
| *2 | No. 2 Compression Ring |
| *3 | Side Rail (Upper) |
| *4 | Side Rail (Lower) |
|
Engine Front |
Position the piston rings so that the ring ends are as shown in the illustration.
Do not align the ring ends.
| *a | Front Mark |
Using a piston ring compressor, push the correctly numbered piston with pin sub-assembly with connecting rod into the cylinder block sub-assembly with the front mark of the piston facing forward.
When inserting the piston with connecting rod, do not allow it to make contact with the No. 1 oil nozzle sub-assembly.
Match the numbered connecting rod cap with the connecting rod.
| *a | Front Mark |
Check that the front mark of the connecting rod cap is facing in the correct direction.
Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.
Temporarily install the connecting rod bolts.
Step 1
Using SST, alternately tighten the 2 connecting rod bolts of the connecting rod cap.
Step 2
| *a | Paint Mark |
|
Engine Front |
Mark the front of the connecting rod bolts with paint.
Further tighten the connecting rod bolts an additional 90° as shown in the illustration.
Check that the paint mark is now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Inspect the connecting rod thrust clearance.
Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>CYLINDER BLOCK>INSPECTION